-
product
(25kN) Fatigue Testing Systems
8872
The 8872 fatigue testing system is ideal for fatigue and static testing of biomedical, advanced materials, and manufactured components. The servohydraulic actuator is conveniently located in the crosshead for easy table mounting. The T-slot base makes it easy to secure orthopaedic specimens, automotive components, and manufacturing assemblies. The adjustable crosshead, actuator-mounted load cell, and corrosion resistant T-slot base with unique drain channel are essential for testing biomedical specimens immersed in a saline bath.
-
product
Shadow Sizing
The Shadow Sizer measures size, shape and velocity of particles using backlighting and image analysis software based on the shadowgraphy technique.The Shadow Sizer can measure a wide range of particles types including bubbles, liquid droplets, solid particles and any object with a well-defined contour.Data is analyzed by DynamicStudio and includes histograms of size distribution, 2.5D spatial distribution plots, cumulative histograms and tables.
-
product
Venturi Flow Measurement Trainer (UITM-22)
Unitech Scales And Measurements Pvt. Ltd
UNITECHS venturi flow measurement trainer comprises of an Venturi meter fitted between the piping. A small FHP pump is used to circulate the water through the piping. Pressure ports brought out from the Venturi meter are connected to a U tube mercury manometer to measure the pressure difference. Collecting tank of capacity 5 liter is provided with graduations to measure water level. Digital timer is fixed to calculate the flow rate. Flow can be controlled using a manual control valve. The complete setup is mounted on a table top model.
-
product
Probe Accessories Kit
PK003
Probe accessories are supplied as kits for the various probe models and can be purchased separately.The table below lists the contents of each kit and the probes with which it is compatible.
-
product
MIL-STD-1553 MCH
M4K1553MCH
The M4K1553MCH interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M4K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time...show more -
product
3D Inspection Service
The reference data may come in the form of a table, with values at specific points or features, a cad model, or 3d scan. 3D inspection services may require datum measurements, where the part to be inspected is located in a fixture that is specifically designed to orient the part by an ordered method. In some cases, the part may have features that are designed specifically to be referenced by datums, if no functional feature of the part provides a clear reference.
-
product
Optical tables
The primary goal of a well designed optical table is to eliminate relative motion between components of test system located on the surface of the optical table because such motion can generate measurement errors.
-
product
Handheld Metal Hardness Tester
TIME®5330
Beijing TIME High Technology Ltd.
Handheld Metal Hardness Tester TIME®5330 is loaded with 4.3 inch LCD screen and a large memory of 2000 groups of data. Built-in conversion table enables you to read HB value directly if D/DC impact devices are installed.
-
product
Air Velocity Meter
400
Measure both pressure and air velocityRead the red figures directly in feet per minute of velocity - from 400 to 10,000 fpm No conversion tables needed for air at standard conditions. Read the black figures in inches of water column air pressure - from 0 to 10" w.c.
-
product
1kV, 25 MHz High Voltage Differential Probe with Auto Zero Disconnect
HVD3102A
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
Magnetic Field Scanner
MAGNET-PHYSIK Dr. Steingroever GmbH
Magnetic field scanners measure the magnetic field around permanent magnets or magnetic systems. The results can be output as a colored 2D, 3D representation or as a table.
-
product
2-Axis Rate and Position Tables
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
product
Force Gauges
Morehouse Instrument Company Inc.
Minimize user error and achieve higher accuracy with Morehouse Digital Force Gauges. These instruments display the applied force value directly and do not need an interpretation table. Morehouse analog Ring Force Gauges can also be upgraded to the new digital system.
-
product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concu...show more -
product
Coherent Synthesizers
Innovative Technical Systems has developed high-performance agile microwave synthesizers with truly phase-coherent frequency switching at any step size. These synthesizers offer frequency coverage from 250 MHz to 18 GHz (ACS-25018) or 850 MHz to 18 GHz (ACS-85018) and frequency resolution under 0.1 Hz. The agile design offers typical switching speeds of less than 300 nsec and programmable amplitude from 0 to +10 dBm from frequency-to-frequency. Spurious performance is typically <-70 dBc. A versatile waveform table design is implemented that allows frequency, amplitude, and output markers to be defined for each step in the table. Waveform table lengths up to 256K are supported.
-
product
VXIbus Module
Universal Switching Corporation
The VXIbus modules offered by Universal Switching Corporation are listed in the table below by "maximum" frequency range order beginning with low frequency (DC) to the highest (40GHz) followed by our soon to be released fiber optic modules. Each module has its own characteristics and features.
-
product
Cable Testers
DMX ADAPTER
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
product
6GHz RF Signal Generator
TGR6000
0MHz to 6000MHz frequency range10Hz setability, ±1ppm frequency stabilityLocking to external frequency standard-110dBm to +7dBm amplitude, 0.1dB stepsFast stepping sweep with dwell times down to 10msList sweep of up to 1000 points of amplitude vs frequencyUser compensation tables for specific test set-upsStorage for 12 generator set-ups and 16 sweep listsCompact half-rack 2U casing uses minimum bench spaceFull remote control through RS232, USB, LAN and GPIBSignificantly lower cost than other 6GHz generators
-
product
Automotive Solutions
Over the years, we have acquired profound, specific expertise in a number of areas, especially with respect to RF assembly and antenna technology testing. To give an example, we have acted as general contractor for implementing a number of rotary indexing tables for testing and labelling antenna amplifiers. The implementation as a rotary table has a number of advantages, since all mounting and test processes, as well as the handling of defective parts, are interlocked and concatenated, thereby effectively eliminating possible error sources during these process steps.
-
product
Laboratory Equipment
Coffee Cupping Table
Take a traditional approach to tasting with our specially designed four- to six-person cupping table.
-
product
Auto Electrical Test Bench
ELAK Auto Electrical Test Bench is a table model and has been designed to cater to the needs of Auto Electricians, Garages, Services Centers, Transport Corporations, Educational Institutions and other bulk users of Auto Electrical Equipments, for complete testing of Alternator, Regulator and their associated parts. It also has a built-in D.C. Power Supply to check Free-run of Starter Motors.
-
product
Downstream And Others
A gas chromatograph is used for impurity analysis of intermediate or final products in various chemical fields. The table below shows our System GC lineup. Access detailed application information by clicking on.
-
product
CoreAFM - the best value research AFM
CoreAFM
The fusion of a modern flexure-guided scanner, XYZ sample stage, camera, active vibration isolation table, and acoustic shielding in a single all-in-one unit results in a complete AFM system with an unparalleled compact footprint. The system comes with a fully digital 24-bit controller developed specifically for the CoreAFM scanhead. All the essential functions of modern AFM are integral components of the CoreAFM system; all you need to do to take the CoreAFM into operation is connect the contro...show more -
product
CORROSION GAUGE
MMX-7
The MMX-7 has all features of the MX & MMX gauges with some additional features and advantages. Selectable Large Digits and B-Scan display options. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and selectable low, medium or high gain options. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVX/PVXview or Java-based PC software makes this thing a complete kit and then some! 2-year limited warranty.
-
product
Optical Tables with Broadband Damping
5100 Series
The 5100 Series features 3/16″ thick ferromagnetic stainless steel top and bottom skins, precision honeycomb construction, our patented SPILLPRUF spill management system, and broadband damping for excellent vibration absorption.Table lengths up to 20′Widths to 6′Thicknesses to 36″We love custom tables! Choose welded splice plates for extra long, wide, and “L”, “T”, or “U” shaped tables. Let us know your unique requirements and we will make it happen!All our optical tables may be paired with Active-Air or Passive-Air vibration isolators, or modular rigid supports, sold separately.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
UHF/RFID Power Divider Combiner 3-Way, TNC Female, 350-1000 MHz, 30 Watts
PD2931
INSTOCK Wireless Components, Inc
PD2931 is a RoHS compliant, 3 way, wideband, 50 ohm, RF power divider, power combiner furnished with TNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 3 way power divider input rating tables for additional details.
-
product
Compact Testers
Adaptronic wiring testers of the compact class are available as low voltage testers and also as high voltage testers, as KT version with display and keyboard and as NT version with the grafical user interface NT Control. With max. 5120 test points (NT 600) adaptronic wiring testers of the compact class are predestined for voluminous testing jobs and large products to be tested. Whether with adapter cables, test tables, test consoles or adapter consoles - the wiring testers of the compact class can also be used everywhere.
-
product
DC Blocking L-Band Splitter Combiner
PD5920
INSTOCK Wireless Components, Inc
PD5920 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other port blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS c...show more -
product
Refractometer Calibration Oils
Calibration Oils are one of the most commonly used materials for calibrating refractometers as they have good traceability, particularly to NIST. Having a high temperature co-efficient, Calibration Oils are best used where strict temperature control is adopted either by Peltier or external waterbath between 10 and 75 °C as well as with refractometers operating at ambient by making use of supplied tables or an RI/°C Temperature Calculator as long as the prism temperature is reliably known.