Showing results: 46 - 60 of 69 items found.
-
RS Series -
Cytec Corp.
The RS Series computer controlled switching systems are designed to switch multi-wire groups of signal up to 25 wires. These systems are typically used for signals such as parallel TTL, RS232, RS422, WAN or modems, but can also be used for any group of analog or digital signals having a bandpass up to 30 MHz or a data rate up to 20 Mbps. A modular design concept is used that provides configuration flexibility by allowing display modules, different control modules and switch modules to be combined into a single chassis.LED displays and switch point status feedback are available on most systems. Computer control via IEEE488 (GPIB) and RS232 is standard, while TCP/IP Ethernet LAN, USB and manual controls are optionally available.
-
ICS Electronics
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Eltima Software
With Serial to Ethernet Connector you can share up to 255 serial devices over network turning your computer into a terminal server. With this serial over network solution any device connected to a COM port can be accessed and used from any spot on the globe as if it were physically connected to the local machine. The data sent by serial port device is transmitted over a TCP/IP network. This is achieved thanks to our virtual serial port technology that emulates standard COM ports behavior and Windows OS treats the virtual ports as the real ones. Although the ports are treated as physical you are not limited to the quantity of physical COM ports and can create COM port connections without occupying real serial ports. With Serial to Ethernet Connector you can: share serial port for incoming connections, connect the port to remote host, or share port using UDP connection. Starting from version 7.0 Serial to Ethernet Connector got absolutely new user interface for even easier creation and management of connections with latter conveniently visualized and more.
-
EQUINOX -
M Squared Lasers
Equinox is a single frequency, 532 nm continuous wave laser designed for a range of scientific applications including pumping any Ti:Sapphire laser systems. It is engineered to meet the needs of experimentalists requiring high-performance systems with an emphasis on reliability, stability and ease of use. The laser incorporates pump diodes within the central unit and is fully automated with hands-free operation and control via ethernet, webpage and TCP/IP remote interface. This completely sealed system is inherently stable with low noise levels <0.05 % RMS and ultra-stable output powers with ±0.5 % stability. Equinox has options of high output power up to 18 W. Other major applications include mixing source, pump source for dye lasers and frequency doublers, optical tweezers, and biomedical imaging.
-
iPQMS-C128 -
Eagle Eye Power Solutions
The iPQMS is the premier battery monitoring system in Eagle Eye's IBwatch-Series. It ensures backup power systems are optimally maintained in large-scale environments. The iPQMS is the main processing unit that measures up to 448 jars (or 448 cells) utilizing up to seven Relaying Units (RU). Each RU connects up to 64 jars (or 64 cells) and captures data from these batteries and sends it to the MPU in real-time. The iPQMS can be used over a private network via TCP/IP, or locally with RS-232. Networked systems can utilize SMS/Email alerts during an alarm outbreak. If you do not wish to use our Battery Management Software, Modbus protocol is available for third-party integration. Flexible expanding solutions allow multiple iPQMS units to monitor all your systems in real-time.
-
IPQMS-C64 -
Eagle Eye Power Solutions
The iPQMS is the premier battery monitoring system in Eagle Eye's IBwatch-Series. It ensures backup power systems are optimally maintained in large-scale environments. The iPQMS is the main processing unit that measures up to 448 jars (or 448 cells) utilizing up to seven Relaying Units (RU). Each RU connects up to 64 jars (or 64 cells) and captures data from these batteries and sends it to the MPU in real-time. The iPQMS can be used over a private network via TCP/IP, or locally with RS-232. Networked systems can utilize SMS/Email alerts during an alarm outbreak. If you do not wish to use our Battery Management Software, Modbus protocol is available for third-party integration. Flexible expanding solutions allow multiple iPQMS units to monitor all your systems in real-time.
-
Model T701 -
Teledyne Advanced Pollution Instrumentation
The T701 adds Modbus TCP/IP connectivity to the proven reliability and performance of our zero air systems. This allows remote monitoring of key instrument functions including dewpoint status, scrubber temperature, box temperature, and output pressure. Additionally, this digital access provides the ability to remotely disable the internal pump, allowing longer service intervals and less power consumption. The user can also remotely start instrument warm-up prior to arrival at the site.The T701 is a fully self-contained source of clean, dry air for dilution calibrators. It can also be used to create purge air for permeation tube ovens or burner air for FID analyzers. The T701 includes a dewpoint sensor, an oil and diaphragm-free pump, and scrubbers to remove SO2, NO, NO2, O3, H2S, and NH3. Optional high performance scrubbers are available to remove CO and Hydrocarbons.
-
Paralan Corp.
Built-in Graphical Interface addressable by any web browser through the Gigabit Ethernet port.Easy installation including self-contained initial IP address and the capability to be used in DHCP over TCP/IP environments. Automatically detects every parallel SCSI device connected to the 68-pin SCSI interface upon power up. Field upgradeable to adapt to future expansions of the iSCSI specifications, and compliant with iSCSI and SCSI interface standards. At-a-Glance status LEDs for SCSI Bus Activity, Self Diagnostics, Power, Gigabit Ethernet Link Status and Gigabit Ethernet Activity. Utilizes a dedicated 833 MHz 32-bit processor for maximum iSCSI and SCSI throughput. Embedded Adaptec Ultra160 SCSI controller chip providing state of the art, reliable control of all SCSI devices. The iS500 Series supports LVD/MSE and HVD SCSI.
-
Model T701H -
Teledyne Advanced Pollution Instrumentation
The T701H adds Modbus TCP/IP connectivity to the proven reliability and performance of our high purity zero air system. This allows remote monitoring of key instrument functions including dewpoint status, scrubber temperature, box temperature and output pressure. Additionally, this digital access provides the ability to remotely disable the internal pump, allowing longer service intervals and less power consumption. The user can also remotely start instrument warm-up prior to arrival at the site.The T701H is a fully self-contained source of high purity zero air for dilution calibrators. It is ideal for use with highly sensitive analyzers in ambient background and trace level applications. The T701H includes a dewpoint sensor, an oil and diaphragm-free pump, scrubbers to remove SO2, NO, NO2, O3, H2S and NH3, plus high performance scrubbers to remove CO and Hydrocarbons.
-
781630-05 -
NI
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
781630-07 -
NI
Ethernet GPIB Instrument Control Device - The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
781630-12 -
NI
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
781630-10 -
NI
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
781630-09 -
NI
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
781630-02 -
NI
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
