Showing results: 5536 - 5550 of 6630 items found.
-
LX-30A+ -
Shenzhen Lian Xin Technology Co., Ltd.
Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .．·used to test single – ends ,double –ends ,three-ends power supply cords.．·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,．·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products， and alarmed with voice prompt and light,
-
ADSE 715 RS -
ATEQ Aviation
The ADSE 715 is a complete high performance single pressure Ps stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air data computers ) and sensors. The high precision embedded sensors enable the ADSE 715 to be used as a pressure standard. The user interface running on a PC connected through USB link is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
-
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
Rexus PST-3 -
Rexus Corp.
ATX PSU each output connectors checkTests 20-pin and 24-pin power suppliesTests SATA powerTests Pentium 4 power connectorTests PCI-Express power connectorsTests Xeon power connectorsTests Floppy drive connectorsTests standard 4-pin power supply connectorsAccurate voltage indicator +/-V(+12V1/+5V/+3.3V/5VSB/+12V2/-12V)ATX P.G value display.Lower or higher P.G values alarmLower voltage detected alarm.Over voltage alarm.No voltage detected alarm.Dimension : H * L *D : 64mm * 150mm * 18mm
-
LS600 -
Lisun Electronics Inc.
• The standard LS600 has 1 Group which has 8 channels. That means LS600 can test 8 LEDs separately at one time. (Optional: it expand to 8 Groups which can test 64 LEDs separately at one time) • Aging Functions: Constant Current, Impact Pulse, On/Off Mode • Output current: 1~1000mA (Special Order Available) • Output voltage: 5V(Special Order Available) • Output frequency: 1~3000Hz, Duty Ratio: 1%-99% • Range of on-off circle: 0~9999h/59m/59s
-
Extech CG304-REF -
Extech Instruments Corporation
The Extech CG304 Coating Thickness Tester offers a non-destructive way of measuring the thickness of ferrous and non-ferrous substrates with automatic recognition of the material being measured. Memory stores 2500 readings. The unique Bluetooth® interface feature wirelessly transmits data to your PC for further analysis, and it enables you to generate a documented report. Includes a special LCD with backlight feature and contrast for easy viewing in various lighting conditions. Complete with two AAA batteries, software, hard case, steel and aluminum substrates, and standard films for calibration.
-
Extech CG304 -
Extech Instruments Corporation
The Extech CG304 Coating Thickness Tester offers a non-destructive way of measuring the thickness of ferrous and non-ferrous substrates with automatic recognition of the material being measured. Memory stores 2500 readings. The unique Bluetooth interface feature wirelessly transmits data to your PC for further analysis and enables you to generate a documented report. Special LCD with backlight feature and contrast for easy viewing in various lighting conditions. Complete with two AAA batteries, software, hard case, steel and aluminum substrates, and standard films for calibration.
-
SCR ELEKTRONIKS
The product is designed to carry out Arc Ignition Test as per IS/IEC 60947-1 Clause 8.2.1.1.2 (material used for electrical products). The adjustable current source is 230V AC @ 33A. The load is adjusted to get 32.5A at 0.5 power factor. Included on control unit are Digital Voltmeter, Digital Ammeter, Digital Power Factor Meter and Micro Controller based programmable Sequence Timer with LCD display for display & setting. The arrangement is made to mount the test piece with electrodes as per the specification given in the standard.
-
CMW270 -
Rohde & Schwarz GmbH & Co. KG
The R&S®CMW270 is the ideal test solution for integrated wireless communications solutions as used in laptops, netbooks, game consoles, data cards, wireless headsets and other products of the IoT market. Within the R&S®CMW500 - Production Test product family, the R&S®CMW270 offers functionality tailored to the above applications. The tester provides network emulation (signaling mode) for WLAN and Bluetooth® as well as generator and analyzer functionality for standards such as WLAN, Bluetooth®, GNSS and broadcast technologies.
-
7A -
Picoprobe
An unterminated version, can be used for capacitance and resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
-
193942-02 -
NI
9-Pin, Male SAE J1962 OBD-II Type A to 9-Pin, Female D-SUB - The OBDII9M-DB9F CAN Cable, sometimes referred to as the CAN OBD-II Cable, connects any NI high-speed CAN interface to an OBD-II compliant vehicle that has high-speed CAN on its diagnostic link connector in the passenger compartment. This high-quality injection-molded cable connects the CAN wires from the SAE J1962 connector to the standard CiA-DS-102 D-SUB connector wiring used by NI CAN interfaces. This cable is available with a high-speed CAN physical layer and no termination.
-
M9120A -
Keysight Technologies
The M9120A high-density matrix offers higher voltage switching of multiple channels in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This 2-wire switch matrix provides the durable armature switches allowing multiple channels to be connected at one time, up to 60W per channel. The 4-wire wide bus can be used to route signals between test instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
N7900 Series -
Keysight Technologies
The Keysight Advanced Power System (APS) N7900 Series is a full-featured supply designed for automated test equipment (ATE) applications that benefit from high-speed dynamic sourcing and measurement. The highly integrated N7900 enables you to accelerate your test-system throughput with industry-leading speed and precision measurements. The APS N7900 has all the capabilities of the N6900 but also includes dynamic output power, dynamic measurements, and higher accuracy. While standard on the N7900, high accuracy, dynamic sourcing, and power are available as separate options on the N6900.
-
81491A -
Keysight Technologies
Keysight's 81491A Reference Transmitter is designed to offer excellent eye quality for NRZ and PAM4 signals at baud-rates up to 32Gbaud and can serve as universal E/O converter. It comes in Multimode (MM) and Single-Mode (SM) flavors and includes internal lasers at 850nm (MM) or 1310&1550nm (SM). External optical input for usage with tunable laser sources is available for SM option. It is fully integrated into Keysight’s Optical Receiver Stress Test solutions to address test requirements of IEEE 802.3 10,40,100 and 400GBASE optical standards.
-
M9101A -
Keysight Technologies
The M9101A, a high-density, 64-channel PXI multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time or, if needed multiple channels can connect simultaneously. Ideal for routing multiple analog signals to a measurement device in automated test environment (ATE) or data acquisition systems. Each channel switches a high and a low for 2-wire switching up to 100Vrms, with up to 10W of power. Connection options include the durable connector block or the standard cable connections.
