Showing results: 4726 - 4740 of 6631 items found.
-
SEN-30103-J1 -
Playing With Fusion Inc
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
SEN-30103-K0 -
Playing With Fusion Inc
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
SEN-30103-K1 -
Playing With Fusion Inc
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
GIFT Server -
Genmark Automation
The Genmark Integration Framework and Technology (GIFT) development kit is a set of software components, tools and techniques used for rapid development of equipment automation applications. It offers off-the-shelf factory host-computer interface, which are compliant with all related SEMI standards. The product features advanced user interface, broad range of supported automation hardware and presets for many 300mm semiconductor factories.
-
CSF-400 -
Power True Systems Corp.
Measuring frequency. Accuracy: +/- 0.05%. 4 Digital display: 9999 Input Max. 400Hz/600 V, 30KHz/12V. Aux. Power AC 115/230V +/-15%, 50/60Hz. Isolation Aux. Power 12Vdc, 24Vdc, 48Vdc, 110Vdc available in option. Easy-to-wire, screw type terminal. Outside dimensions is DIN standard (96mm x 48mm) High stability & low cost.
-
National RF, Inc
The National RF line of attenuators are compact, affordable attenuators which are ideal for insertion between a direction finding antenna and a receiver/transceiver, to aid in the DF process. In addition, they may be used in the laboratory for a low-power, in-line attenuation purposes. The affordable price is achieved by utilizing standard 5% tolerance resistors and commercial hardware. For laboratory purposes, an attenuation versus frequency curve (to 500mMHz) is provided.
-
ELTRA GmbH
An ELTRA thermogravimetric analyzer is the ideal alternative to standard laboratory ovens and muffle furnaces for thermogravimetric analysis. Thanks to a programmable furnace that is connected to an integrated balance, heating and weighing are combined in one instrument. This saves time-consuming manual work and allows for high sample throughput. In addition, a thermogravimetric analyzer can determine typical parameters such as moisture, ash and volatiles in one single analysis run.
-
CS2-CT -
Chuan Sheng Electronics Co., Ltd.
The CS2-CT provides high speed and multifunction, counting, control and communication (Modbus RTU mode) of Pulse from flow meter or encoder, proximity switch, photo switch for length control.There are 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue,and RS485 port available. They are also support N, R, C mode for totalizer control.
-
Zetec, Inc.
Zetec scanning systems provide accurate and efficient scanning of surfaces. Our scanners are aided by our software for control of the scan to cover the inspection area and to acquire the scan data. Whether you’re inspecting with eddy current or ultrasound, you can take advantage of one of our standard scanning solutions, or have us customize a scanning solution to fit your specific needs.
-
AC-LB-Series -
Eagle Eye Power Solutions
Eagle Eye AC Load Banks are commonly used for testing generator sets, UPS units, aircraft power inverters and other government and military AC power sources. The Eagle Eye AC LB-Series is the smallest in the industry and offers unmatched durability in even the harshest testing environments. Eagle Eye offers several standard models as well as custom AC Load Banks.
-
T1000-9 -
Tesuto Systems
T1000-9 breakout box is our most compact breakout box, using dual 9 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 18 test points plus a ground jack. All test points use standard size 4mm banana jacks. Ideal for continuity testing, isolation testing or signal capture and monitoring.
-
Insight Product Company
Insight Product Company offers terahertz lasers at frequencies from 0.89 to 2.52 THz. Output power is from 1 mW to 15 mW. Diameter of the output wave beam is ~ 40 mm. Typical sizes is 1.2x0.3x0.4 m. Transformer from quasi-optical output to the standard wave guides can be provided. The energy pumping is provided either by DC discharge or HF discharge.
-
AS-LM01-CME-A -
Active Silicon
The LM01 COM Express Embedded System is the core processing “engine” in the USB3 Vision Processing Unit but is available as an unhoused OEM unit, available with a variety of interfaces through the use of its PCIe/104 expansion capability. Using high performance Intel i7 and similar processors and with all the usual standard PC interfaces available, this unit is readily adapted for many embedded system applications.
-
Communications & Power Industries
CPI SMP Division provides a complete line of high-powered continuous wave (CW) and pulsed instrumentation amplifiers for EMC testing, available in octave and multi-octave bandwidths from 1.0 GHz to 95.0 GHz and power levels exceeding 2.0 kW to meet the new military and automotive standards. CPI is the only supplier that manufactures both the traveling wave tube (TWT) and the TWT amplifier.
-
WECO SMART AMI -
Radian Research, Inc.
Radian Research raises the standard once again to provide a new, innovative solution to Electric Utilities for their meter testing and evaluation needs. RADIAN’s fully customizable WECO SMART AMI Meter Farms utilize the XBee IOT Ecosystem to provide wireless remote control of core functionality at every WECO SMART AMI Meter Farm row independently for unprecedented convenience and versatility.
