Showing results: 2341 - 2355 of 2906 items found.
-
34946A -
Keysight Technologies
The Keysight 34946A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as two independent 1x2 (SPDT) terminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
U8030 Series -
Keysight Technologies
The Keysight U8030 Series variable DC power supply has a total output of 375 W—making this solution an ideal power source in the design and manufacturing of electronic devices. The U8030 Series power supplies feature an output sequencing capability for semiautomated tests. These power supplies enable you to generate output sequences with minimal programming skills. This solution features excellent load regulation and clean output noise for continued stability.
-
11667A -
Keysight Technologies
The Keysight 11667A power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 18 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
289 SVD -
Standard Electric Works Co., Ltd
● Bright LED visual indication● Audible indication● Mute function● AC voltage detection: 100Vac ~ 69kVac● Frequency range: 50/60Hz● Easy-to-prove method● Self-test function● Power source: 1.5V(AA) alkaline battery × 3● Non-contact detection by proximity● Personal sensor, easy to wear and convenient to use● Can be attached with hot sticks by optional accessory● Lightweight, robust and compact● Easy access to batteries Comply with EN 61326-1
-
4338 mO -
Standard Electric Works Co., Ltd
● Protection class: IP65 (Lid closed)● 4-Wire method for mΩ.● It's about 100mA at 1100.0mΩ range.● It's about 10mA at 11000mΩ range.● Measures down to 100µΩ (0.1mΩ).● Maximum resolution of 100µΩ.● Large LCD (68×34mm).● Relative mode. ● Data hold function.● MAX/MIN function.● Power source: 1.5V "C" battery × 8● Long battery life and stable power. ● Low battery indication.
-
FMC165 -
Abaco Systems Inc
The FMC165 provides two 14-bit analog-to-digital (A/D) channels supporting RF sampling at 2.6 GSPS and one 14-bit digital-to-analog (D/A) channel with sampling rates up to 5.2 GSPS (2.6 GSPS direct RF synthesis). The converters are clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users.
-
Extech 412400 -
Extech Instruments Corporation
The Extech 412400 Multifunction Process Calibrator sources and measures thermocouples (J, K, and T), mA, mV, and V devices. The 24 V loop supply drives current loads up to 1000 ohms. It has memory for 5 user-settable output values of each type for fast calibrations. Single and continuous step function for voltage and current. Comes complete with six AA batteries and a calibration cable with spade lug terminals.
-
Environment Associates Inc.
Products with moving parts, electromechanical components, filtering systems and electronics are all susceptible to fine and large particle dust that can contaminate a product. These contaminates can cause premature failures and loss of function.Today’s test plans for phones, computers, vehicles, enclosures and aircraft include sand and dust testing to determine if this stress source would cause functional deterioration.Our services include military and automotive dust testing for both blowing and agitated dust and sand.
-
Edinburgh Instruments Ltd
AGILE features a broadband spectral output from <400 nm to >2000 nm and pulse repetition rates from 10 kHz to 1 MHz, making it the ideal light source for the majority of fluorescence lifetime applications. Using the Time-Correlated Single Photon Counting (TCSPC) technique, fluorescence lifetimes from a few picoseconds to microseconds can be accurately resolved. It is also compatible with Multi-Channel Scaling (MCS) mode for lifetimes up to 10 μs.
-
G5.SAS -
Regatron AG
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
Model：OLT-20 -
ShinewayTech
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
HMI/SCADA -
Wonderware
Centrally develop, manage, upgrade, scale and maintain all automation control, data and visualization systems under one user friendly, integrated and powerful environment. unifying and arming control operators, maintenance personnel, IT professionals, plant managers and business executives with one common standardized source of real-time highly contextualized information and with collaboration and analysis tools to better understand the business, make better decisions, and drive the company to its fullest potential.
-
Element 1 Power Systems Inc.
The fuel cell will change our lives as much as the computer it powers and the internal combustion engine it replaces. The future of power and transportation will change dramatically when fuel cells become the main producers of clean energy. The car will no longer be an environmental burden, and the electrical grid will be subdivided to the neighborhood and building level. The quality and reliability of this alternative energy source will be superior to the current grid design. Fuel cells and hydrogen technology will make all of this possible, and with little or no pollution.
-
ELE International
Aggregates are one of the most important construction materials, used as a composite material in concrete and asphalt, and as a base material in foundations, roads, and railways. The high hydraulic conductivity of aggregates also makes them ideal for drainage applications and as filter media. With so many different applications, ELE’s range of aggregate testing equipment performs a vital role in checking performance characteristics against specifications, quality control, new source assessment and the prediction of in-service behaviour.
-
NF Corp.
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
