Showing results: 1696 - 1710 of 2910 items found.
-
Avionics Interface Technologies
Certified “Compatible with LabVIEW” PnP Driver - Includes high level LabVIEW VI’s for controlling AIT MIL-STD-1553 InstrumentsCompatible with LabVIEW Real-Time (Including NI Linux Real-Time) - Includes documented APIs with source code examples for LabVIEW (VI), C, C++, & C#/.NET - Integrates with AIT’s Flight Simulyzer software (share XML bus configurations between API’s and Flight Simulyzer) - Support provided by AITs industry leading applications engineering team
-
Model KM-MPS-50K -
Kusam Electrical Industries Limited
• AC 50kV and DC 50kV measurement with direct reading.• 4000-count LCD.• Input impedance : 400 Mohm• Auto-ranging : AC : 4.000kV / 40.00kV / 50.0kV, DC : 4.000kV / 40.00kV / 50.0kV• KM 50K must be connected with an approved hot stick (Optional).• Check phases are "in-phase" or "out of phase".• Polarity indication : Positive / Negative• Backlight function.• Auto power off.• Power source : 1.5V(AA) alkaline battery × 2.• Low battery indication(Multi-level).
-
MT7553 Series -
Maury Microwave Corporation
Noise Parameters are the non-50Ω extensions of Noise Figure, and are an important modeling and model validation tool to understand how a device-undertest’s performance changes as a function of source impedance. Noise Parameter measurements are typically performedusing a Vector Network Analyzer (VNA) to measure the S-Parameters of the DUT, and a Noise Analyzer (either Noise Figure Analyzer NFA or Spectrum Analyzer SA) to measure the noise power of the DUT. Noise parameters are calculated from a combination of knownsource impedances, S-parameters and noise powers.
-
A600 -
FLC Electronics Inc
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
A400 -
FLC Electronics Inc
The A400 is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of 200. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
A800 -
FLC Electronics Inc
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
F10A -
FLC Electronics Inc
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
F20A -
FLC Electronics Inc
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
DeltaTRAK
The Temperature/Humidity/Dew Point Circular Chart Recorder uses a red pen to track temperature and a blue pen to track humidity, permanently recording these measurements on a 6-inch (165mm) diameter paper chart. Power is supplied to the temperature recorder through a 110V AC 50/60 Hz plug-in adapter for Model 14013 and a 220V AC adapter for Model 14014. External power may be supplied from any 12V DC source such as automotive, marine or other battery.
-
HHB C -
C.Scope International Ltd
*High sensitivity, twin coil induction balance metal detector. *Dimensions 9cm x 28cm x 3.2cm*PP3 type battery power source. Low battery indication. *Long battery life.*Normal operating temperature range -9º to +54ºC.*High impact ABS construction. Comfortable to hold and lightweight.*Audio and visual indication of metal.*Simple, single control operation. No specialist knowledge required.*Earphone socket, for use in noisy work situations.
-
KT-8000 -
KILTER ELECTRONIC CO.,LTD
8000 counts with apheliotropic display, analog bar 40 segmentsAuto power off, full DMM functionAuto data hold ,peak holdFrequency test range up to 999.99999MHz(8 digits)18 kinds of frequencies,1800 waveform output-standard function producerCapacitance test: 1nF ~100μFTemperature test: -50℃~1372℃Decibel test: 20 loading resistance for choose36 hours relative value testPhotoelectricity Isolation RS-232 interfacePower source: 9V 6F22 battery
-
Renesas Electronics Corp.
RV2X6376A Series of directly modulated laser (DML) diodes deliver 25 Gbps x four wavelengths as the light source in 100 Gbps optical transceivers that enable high-speed communications inside 4.9G and 5G LTE base stations, and between data center routers and servers. The RV2X6376A Series are the industry’s first industrial-temperature (-40°C to 95°C) DML diodes that support full 25 Gbps speed (per individual laser) without cooling.
-
FMC216 – HPC -
Sundance Multiprocessor Technology Ltd.
The FMC216 is a sixteen-channel DAC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC216 provides sixteen D/A 16-bit 312.5Msps (2.5Gsps with x8 interpolation) channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC216 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled capable.
-
EM1 -
U. S. Digital
The EM1 is a transmissive optical encoder module designed to be an improved replacement for the Avago HEDS-9000 series encoder module. This module is designed to detect rotary or linear position when used together with a code wheel or linear strip. The EM1 consists of a lensed LED source and a monolithic detector IC enclosed in a small polymer package. The EM1 uses phased array detector technology to provide superior performance and greater tolerances over traditional aperture mask type encoders.
-
ACT2500 Series -
Acumentrics Inc.
Acumentrics continues to provide innovative, rugged, reliable power solutions with the introduction of the ACT2500 Power Conditioner. This durable and versatile power conditioning system contains advanced double on-line conversion to provide power conditioning for electronic devices, meeting the rigorous needs of soldiers operating around the world. The ACT2500 "Vetronics" ready design makes it perfect for combat vehicles including the JLVT, FMTV and HMMWV along with any other application that relies on 28VDC as a source of power.