Solar Simulators
replicate the sun's light.
See Also: Solar Simulation, IEC 60904-9, I-V Tracers, Solar Reference Cells
-
product
Solar Simulators
Abet Technologies offer a wide range of ASTM, IEC, and JIS standards compliant solar simulators ranging from 150W to 3kW with one sun or greater illuminated field sizes from 50 x 50 mm to 35 x 35 cm. The direction of illumination, traditional down pointing, horizontal, or vertical up pointing can be specified at the time of ordering.
-
product
Flash Solar Simulators
Sciencetech manufactures a range of flash solar simulatorsSee the Flash Solar Simulator Overview to compare products across different product lines.
-
product
Sunlite Solar Simulators
- Gen III Optics for High Efficiency Illuminati- Infinitely Adjustable Irradiance, Reproducibly Settable- Class A AM1.5G Spectral Match- ASTM Class A stability- 50×50 mm Class B uniformity- Manual Shutter Included, Electronic - Shutter Optional- Uninterrupted testing with the prealigned lamps- HEPA filtered air cooling
-
product
Solar Simulators
TriSOL CPV
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
product
Highly Collimated Solar Simulators
This solar simulator is based on a Fresnel lens to collimate the light beam from the arc lamp source to infinity, which results in highly collimated illumination of the target spot. A 2.5kW xenon ozone free lamp is used as the light source. The spectral distribution of the xenon light source, along with the use of specially calibrated AirMass filters, closely simulates the sun’s true spectral distribution in various conditions on Earth.
-
product
Modular Solar Array Simulators
MP4300A Series
The output power of solar cells varies with numerous environmental conditions (e.g., temperature, irradiation) and operational conditions (e.g., eclipse, spin). The Keysight MP4300A Series solar array simulator enables you to test all these conditions with high accuracy. It delivers fast current-voltage (I-V) curve changes with a quick recovery time, emulating rapidly changing conditions.
-
product
Module Solar Simulators
QuickSun® 800-Series
800-Series simulators are always tested, certified and results reported exactly as specified in the applicable solar simulator standards and this is being proved by a globally recognized inspection body, SGS Fimko Ltd.
-
product
Large Area Solar Simulators
The LASI Beam Turner assembly allows the output of the LASI to be projected horizontally. It attaches to to the standard LASI downward facing stand that is included in the base LASI system.
-
product
Large Area Pulsed Solar Simulators
Alpha-Omega Power Technologies, LLC.
AOPT introduces the large area pulsed solar simulator capable of generating a CLASS A output over a large area of 3.5 meters by 3.5 meters.
-
product
Fully Reflective Solar Simulators
Sciencetech manufactures four high power versions of class AAA fully reflective solar simulators. Sciencetech''s proprietary fully reflective design uses metal coated mirrors and passes the whole spectrum, no compromise. This is a distinct advantage over refractive based systems that are limited by the properties of the transparent material used.
-
product
Close Match Solar Simulators
We design and manufacture a wide range of world leading solar simulators that meet and surpass the IEC, ASTM and JIS international standards. Our close spectral match solar simulators are used across the globe in world-leading laboratories. Our award winning Unisim solar simulators are used in both research and development work as well as 24/7 production facilities and are regularly cited in the latest photovoltaic research literature.
-
product
Solar Reference Cell
The Solar Reference Cells consist of a 20 mm x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 mm x 70 mm x 16 mm metal enclosure with a protective quartz window and a temperature sensor. Designed for calibrating the irradiance of solar simulators used for testing solar cells and modules.
-
product
DC Power Supply
DC power supplies offer many unique advantages for telecom, automated test system & integration, industrial, battery charge & simulation for hybrid cars and solar panel simulation. These advantages include high power density of 15KW in 3U, precision readback of output current and voltage, output trigger signals as well as the ability to create complex DC transient waveforms to test device behavior for spikes, drops, and other voltage deviations.
-
product
Solar Simulator Testing Kits
Solar Light’s Solar Simulator Testing Kits are designed for scientific and industrial professionals who want everything they need to begin testing all in one comprehensive package.
-
product
Standard & Custom Test Fixtures
Both standard and custom Test Fixtures from OAI enable the user to integrate the solar cell with the I -V tester. Fixture configurations range from from simple hold down devices to temperature-controlled fixtures with front and back side contact. We invite you to contact an OAI Application Engineer for help with your fixture design. With our expert guidance, you can expect maximum performance from your I -V Tester and Solar Simulator.
-
product
Solar Simulator
Excellent reputation for its high degree of throughput, accuracy and stability. Pulsed light is used, ensuring stable measurement. Approximates the spectral distribution of AM 1.5G reference solar radiation. Achieves accurate measurement of various modules. No need to reverse modules, facilitating in-line operation.
-
product
Modular Solar Array Simulator Mainframe, 1200W
E4360A
The Keysight 1200W, E4360A Modular Solar Array Simulator is a 2U high, 2-slot mainframe that accepts up to 2 E4360 series modules. Modules are ordered separately. It offers LAN, USB, and GPIB interfaces standard.
-
product
Solar Array Simulator
62000H-S series
The latest programmable solar array simulator power supply 62000H-S Series released by Chroma provide simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000H-S provides an industry leading power density in a small 3U high package. The solar array simulator is highly stable and has a fast transient response design, which are both advantageous to MPPT performance evaluation on PV inverter devices. The 62000H-S Series have many unique advantages including high speed & precision digitizing measurement circuits with a 100kHz A/D, 25kHz D/A controlled I-V curve and a digital filter mechanism. It can simulate an I-V curve accurately and response the mains ripple effect from the PV inverter. In addition, the built-in EN50530/Sandia SAS I-V model in the standalone unit can easily program the Voc, Isc, Vmp, and Imp parameters for I-V curve simulation, without a PC controller.
-
product
Solar Array Simulator
SAS
AMETEK Programmable Power, Inc.
A spacecraft solar array is subjected to large temperature excursions, varying insolation (the amount of sunlight falling on the array), mechanical changes and aging, which substantially effect both its short and long term performance. In order to test the spacecraft's power environment, a cost-effective solution for ground based testing is to utilize a solar array simulator.
-
product
Solar Array Simulator Auto-Ranging Module 0-160V, 0-10A, 1kW
MP4361A
The Keysight MP4361A is a 1000 W solar array simulator DC power module that simulates the output characteristics of a solar array. The MP4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin, etc.).
-
product
6″ (15.25 cm) 1000W Pre-Irradiation Solar Simulator
Model LS1000-6S-009
1000W Pre-Irradiation Solar Simulator Kit specifically designed for the pre-irradiation step during in vitro broad spectrum sunscreen testing. Fully compliant with the most current FDA and ISO requirements. The 6″ (15.25 cm) Class A beam can irradiate up to 9 PMMA plates simultaneously.
-
product
Solar ATE
MS 1534
The Inverterless ATE is an automatic test equipment which is used to test the all functional and various test conditions of Inverterless Solar Unit. This ATE shall be a GO/NOGO Tester for Inverterless Solar Unit. All production units can be tested with this ATE for functional testing and clearance. This ATE reduces the man effort for quality checks and detects the failure units. The Inverterless ATE can check the UUT with minimum user interactions. It shall test and generate test report in PDF format for the conducted tests with necessary data. The ATE operates on 230V AC power. The ATE has In-Built AC-DC converter which provides 12V DC for operate the unit. Also it has additional AC-DC converter to simulate solar power to the Inverterless units. The main objective of the ATE is to test the Inverterless S in all possible test scenarios without external test equipments and less user interactions.
-
product
Solar Array Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
product
Continuous Wave Solar Power Meter
The OAI Continuous Wave Solar Power Meter is an essential analytical tool for measuring the irradiance (in Suns) of Continuous Wave Solar Simulators. OAI’s Solar Power Meters feature unique features not found in other Solar Meters. This versatile meter can display a wide variety of cell characteristics that include: cell type, window type, cell size, and temperature measurement device type. The OAI Continuous Wave Solar Power Meter can sample and display a continuous reading or peak reading. The Power Meter connects via USB port for data collection, and includes desktop software. With this small, portable, battery-powered meter, numerous production solar simulators can be tested and compared in a short amount of time, leading to greater production line consistency and throughput.
-
product
Solar Simulator
Unisim Compact Solar Simulator
The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available). The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
product
Solar Array Simulator DC Power Supply
62000H-S
Chroma Systems Solutions, Inc.
Solar Array Simulator DC Power Supplies by Chroma provide programmable simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000S-H series provides an industry leading power density in a small 3U high package. The Solar Array Simulator is highly stable and has a fast transient response design, which are both advantages to MPPT performance evaluation on PV inverter devices.
-
-
-
product
DC Power Supply
62000H
Chroma Systems Solutions, Inc.
Chroma’s new 62000H Series of programmable DC Power Supplies offer many unique advantages for telecom, automated test system & integration, industrial, battery charge & simulation for hybrid cars and solar panel simulation. These advantages include a high power density of 15KW in 3U, precision readback of output current and voltage, output trigger signals, as well as the ability to create complex DC transients waveforms to test device behavior to spikes, drops, and other voltage deviations. For high power applications, parallel up to 10 units for up to 150kW.
-
product
TriSOL Class AAA 0.25º Collimation Angle Solar Simulators
For high performance space applications, OAI offers a 0.25 Collimation Angle Solar Simulator. It is engineered with the technology built on OAI’s 47 years of experience working with light. Features include 100mmx100mm beam size, long lens housing, AM 1.5 G and AMO spectrum up to 1800 nm or any custom spectrum, and intensity controlled up to 1.25 SUNS. These solar simulators are built with OAI’s precision, quality and reliability.
