Showing results: 3826 - 3840 of 5682 items found.
-
METRISO® 3000 -
Wolfgang Warmbier GmbH & Co. KG
Suitable for resistance point-to-point and resistance to ground measurementsIntegrated data logger with USB communication port for data transmission (50.000 test values). The supplied Report Generating Software ETC allows to generate a complete test reportA barcode scanner can be used in order to record measurement points before testing
-
SensorXplorer™ -
Vishay Intertechnology, Inc.
Each sensor board can be used together with the SensorXplorer board.The SensorXplorer boards acts as a USB to I2C interface between Vishay's freely available software modules and the sensor boards. The sensor boards also have test pins for the I2C interface, allowing you to connect them to your own platform.
-
E9903G -
Keysight Technologies
Test efficiency, test system stability, and seamless equipment integration. Keysight’s i3070 Series 6 family provides those improvements built upon a proven technology foundation. With time-tested software, hardware, and programmability, the Series 6 are fully backward compatible with previous systems, and they make highly repeatable measurements.
-
Eaton Corp. Electrical Group
Eaton’s power quality portfolio encompasses a comprehensive offering of power management solutions from a single-source provider. This includes uninterruptible power supplies (UPSs), DC power solutions, surge protective devices, switchgear, power distribution units (PDUs), remote monitoring, meters, software, connectivity, enclosures and services.
-
CLIOQC Model V -
Audiomatica
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Model T200 -
Teledyne Monitor Labs
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor.A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T200 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
AIM GmbH
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
ADLINK Technology Inc.
With the advantages of PC industry innovation and manufacturing, and by natively leveraging PC technologies of PXI, ADLINK adopts the latest technology and improves cost reduction. With a rich history in measurement and automation, as well as in hardware design and software integration, ADLINK provides a broad portfolio of high performance products with higher speed/bandwidth bus interfaces.
-
Model 3150 -
TSI Inc.
The Component Filter Test System (CFTS Model 3150) from TSI, consists of software and a hardware module to provide an off the shelf solutions for all your custom filter testing needs. Pre-configured to work with TSI’s world class detectors and sizers the CFTS provides a platform for numerous filter test applications.
-
NI
PXI GPIB Instrument Control Modules feature IEEE 488 controllers for PXI systems. You can choose an option that supports Gigabit Ethernet transfer speeds. PXI GPIB Instrument Control Modules include a license for the industry standard NI-488.2 driver software enabling reliable connections to third-party instruments with GPIB.
-
Great River Technology, Inc.
The Video and Protocol Analyzer (VPA) verifies compliance of designs against the ARINC 818 standard. The VPA software and interface accurately and efficiently decode and display data and flag errors. Multi Stream is a new standard feature of the VPA, empowering it to tackle ARINC 818 interfaces with multiple embedded streams of high-speed video.
-
ARINC CPCIC-A429/PXI -
Alta Data Technologies LLC
The ARINC CPCIC-A429/PXI Interface Card and AltaAPI Support Software Represent the Latest ARINC 32-bit FPGA Protocol Engine Technology. Encode and Decode almost Any ARINC-429 PHY Level Label/Word Signal. The First Card in the Industry to Offer Advanced Test Functions of Signal Generation and A/D Signal Capture.
-
80-91 -
Testing Machines, Inc.
The Lab Master® Peel Tester for Release and Adhesion testing operates with Windows®-based software, and features the ability to create user-defined test set-up, individual test speed selection, user-definable default areas for analysis, exporting of graphs or data to Microsoft Excel and SPC programs, and enhanced calibration procedures.
-
Updoer Technology
At UpDoer Technology, we're dedicated to providing you with quick and accurate test results. We offer a range of manual testing services to fulfill your needs and keep your projects on schedule and within budget. We follow a test-driven development approach to ensure quality at every moment of the software development cycle.
-
43-76 -
Testing Machines, Inc.
The new 43-76 Pendulum Impact Tester uses a high resolution optical encoder and state-of-the-art data acquisition software to determine the impact resistance of rigid materials like plastic in accordance with a wide variety of ASTM and ISO test standards for Izod, Charpy, Chip Impact, and Un-Notched Cantilever Beam testing.
