Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
-
product
Oxygen Sensor
KS60145
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
- RS-422 to Fiber Optic Converter
Model 272A
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
DN2.222-02
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
product
Signal Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded with Round Posts (610 138 115)
510151107
Used together with QP ITA module p/n 510109316 for PCB mounting. NOTE: Mounting screws for this module are included with module part # 510109316. Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
product
6 GHz ProBus2 Differential Probe with Dx10-SI Solder-In Tip
D610-A-PB2
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SOSA Aligned 3U VPX
Model 5553
- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- 10 GigE Interface- 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 49, VITA 46, VITA 48, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8256 3U VPX SOSA Aligned Development Chassis- Model 6003 unique ...show more -
product
4 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Mixed Signal Oscilloscope
WavePro 404HD-MS
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s.Up to 5 Gpts of acquisition memory enables detailed viewing of long events.15.6" 1900 x 1080 Full HD capacitive touchscreen.New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector.MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms.Zone Trigger – Simple Triggering for Complex Signals.
-
product
250 MHz Passive Probe for HDO4000, 10:1, 10 MOhm
PP017-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscillosco...show more -
product
Analog Distribution Amplifier
DA 1:54
The DA 1:54 Analog Distribution Amplifier is designed to make it simple to distribute analog signals generated by Spectrum products to multiple locations and to overcome long cable runs. The DA 1:54 consists of three separate amplifier sections that are factory- configured to operate independently or ganged together, depending upon requirements.
-
product
Quad Core KeyStone™ DSP + UltraScale™ FPGA Module
SMT6657-KU35
Sundance Multiprocessor Technology Ltd.
The SMT6657 DSP+FPGA module is a reliable and flexible platform for digital signal processing applications requiring high-performance integer and floating-point computation.It is applicable to both symmetric multiprocessing applications in which the computational load is shared by the two DSPs and asymmetric applications where one of the DSPs is responsible for hard real-time processing and the other acts as a supervisor, handling all non-deterministic communication and optionally running under control of an operating system.
-
product
Signal Isolators
Signal IsolatorsDatexel manufacture a large range of Signal Isolators. The DAT511 is a loop powered isolator with 3000 V galvanic isolation between the input and output. It is a 2 wire device so there is no external wiring. The DAT511H is similar but is Hart compatible. The DAT4035 is a universal input signal (Thermocouples, RTD's, mV, Volts, mA, resistance and potentiometers) conditioner with 2000 V isolation between the input and output and it is PC programmable. It is a 2 wire loop powered device. The DAT4135 is similar but it is a 4 wire device so it has the ability to boost the output or provide a voltage output.
-
product
Party Line Intercom Conversion
COMMS Series
The stand-alone COMMS 300 and the OG-COMMS openGear® units provide a means to interface between two channels of 2-wire party-line intercom audio and two channels of 4-Wire analog line-level signals. The unit is capable of performing auto nulling for each channel with the push of a button. In addition, each of the 4-Wire input and output channel levels are monitored and displayed on easy to understand front panel VU meters.
-
product
PXI-5441, 43 MHz Bandwidth, 16-Bit, Onboard Signal Processing PXI Waveform Generator
779058-03
43 MHz Bandwidth, 16-Bit, Onboard Signal Processing PXI Waveform Generator —The PXI‑5441 is a 43 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms, standard functions including sine, square, triangle, and ramp, as well as signals that require onboard signal processing. Some of these signal processing operations include FIR and CIC interpolation filters, digtal prefilter gain, numerically-controlled oscillator, and I/Q mixing for quadrature digital upcoversion. The PXI‑5441 also features advanced synchronization and data streaming capabilities.
-
product
Automation
50 Hz Adaptive Filter
One of the main causes of the reduction of accuracy in low frequency signal parameters measurements is the influence of artificial and natural electromagnetic interferences on measuring channels of measuring tools (MT). Under laboratory, production and natural conditions, the main interference is 50 Hz network interference. To eliminate this interference, ZETLAB software package uses a program providing a 50 Hz band-stop filter.
-
product
Handheld Radio Frequency Counter
FC1002
A practical frequency counter Frequency range: 1 MHz - 3 GHz Weight: 210g Case: 80 mm * 68 mm * 31 mm stamped aluminum with black anodized finish Battery: Internal 4 * AA 600 mAH NiCd pack 10 digit liquid Crystal Display Low power consumption (Average 6 hour battery life) Hold switch to lock display Low battery indicator Ultra sensitive synchronous detector 16 section bargraph to show RF signal strength High speed 300 MHz direct counter with 0.1 Hz resolution 4 selectable gate speeds
-
product
VTAC Insert
The configurable VTAC high speed data insert features a data transfer rate of more than 12.5 Gbps per differential pair. Gold-plated, self-aligning contacts are specifically designed to reduce crosstalk to increase signal integrity during HSD transfers while maximizing cycle life.Each VTAC insert has a cycle life of over 150,000 without signal degradation.
-
product
PXI Triple 4 To 1 RF Multiplexer, 8GHz 50 Ohm SMA, Terminated
40-882A-003
The 40-881A-003 is a triple 50Ω 4 to 1 RF multiplexer with 8GHZ bandwidth.The 40-881A range of multiplexers have automatic termination of unused signals and are available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules.
-
product
C-Band Mini-Tester
Model 38-4
Kratos Defense & Security Solutions, Inc.
The C-Band Mini-Tester (Model 38-4) is a handheld battery powered unit that provides go/no-go testing for compatible C-Band transponders. The Tester verifies proper transponder operation by interrogating a transponder installed in and powered by a platform. It is capable of testing compatible transponders at distances of up to 350 feet. Indicator lights verify the transmission of signals and the received reply.
-
product
USB Preamplifier, 100 MHz to 26.5 GHz
U7227C
The U7227C, 100 MHz to 26.5 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
product
LXI High Density 256x4 2-Pole 2A Matrix With BIRST
60-556-024
High density double pole matrix capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
product
GPS Antenna Signal Splitter 3 Way, N Type, Passive, L1 & L2, 50 Ohm
GPS300
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsRoHS Compliant Splitter Construction
-
product
PXI Quad 4 to 1 Mux 1GHz 75Ohm 1.0/2.3
40-749-731
The 40-749 is a quad 4 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-749 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals
-
product
Hydrostatic Level Sensor
2250
The Signet 2250 Hydrostatic Level Sensor for level and depth control has a one-piece injection-molded PVDF body and ceramic diaphragm for superior compatibility in corrosive liquids. Utilizing hydrostatic pressure, the 2250 Level Sensor disregards false level signals from steam vapors, foam or any other debris on the liquid surface. Two pressure ranges allow for optimal resolution matched to your sensing needs. Solid state circuitry eliminates drift (no internal potentiometers).
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24AWG Single Conductor Shielded, Single Ended
7-121974000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, 24AWG Single Conductor Shielded, Single Ended.
-
product
1203c Broadband RF Distribution
Precise Time and Frequency, Inc.
The ptf 1203C Broadband RF Distribution amplifier provides high performance frequency references for laboratory or system use.The ptf 1203C uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
product
PXI-6224, 32 AI (16-Bit, 250 kS/s), 48 DIO, PXI Hybrid, Multifunction I/O Module
779114-01
32 AI (16-Bit, 250 kS/s), 48 DIO, PXI Multifunction I/O Module—The PXI‑6224 offers analog input, correlated digital I/O, two 32‑bit counter/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 18GHz, 50Ω, SMA, Terminated, Remote Mount
40-785C-523-TE
The 40-785C-523-TE (PXI) and 42-785C-523-TE (PXIe) are triple SP6T 18GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
MXA Signal Analyzer, Multi-touch, 10 Hz to 50 GHz
N9020B
Quickly adapt to evolving test requirements of wireless devices Shorten test times with hardware-accelerated power measurements, rapid display updates and marker peak searches and fast sweeps Simplify testing with one-button measurements from X-Series applications Capture elusive or transient signals with full-band real-time spectrum analysis
-
product
TMR Magnetic Pattern Recognition Sensors
MultiDimension Technology Co.,Ltd.
A type of 6 channels magnetic pattern recognition sensor built-in the signal conditioner and SPI interface Consists of TMR magneto-resistance sensor, high-quality magnet, high-strength plastic base and durable non-magnetic stainless steel cover; Are used for detecting the paper bills, bank notes and security documents with magnetic anti-counterfeiting consists.
