Showing results: 1816 - 1830 of 8181 items found.
-
LT-880 -
Scitec Instruments Ltd
The LT-880 Laser Tachometer is a non-contact instrument designed to sense the presence or absence of a reflective surface in its optical beam. A TTL signal is asserted whenever a reflective surface is placed within its field of view. The signal may be used with a counter or spectrum analyser to sense linear translation, rpm or transient vibrations.
-
AE700 -
Deviser Instruments
AE700 is a DWDM Channel Analyzer for the installation and maintenance of DWDM systems. The handheld unit is able to measure wavelengths in the c-band, which is from 1530 to 1565 nm. The AE700 also supports optical signal to ratio (OSNR) which is essential for verifying signal quality. The measurements can be displayed in both graphical or list formats.
-
Premier Electrosystems
Premier Electrosystems deals in a wide range of voltage and current sensing devices. A Current/ Voltage sensor is a device that detects electric current/ voltage in a circuit and generates proportional signal. The generated signal can be then used to display the measured current in an ammeter, or can be stored for further analysis in a data acquisition system, or can be used for the purpose of control.
-
ZET 440 -
ZETLAB Company
Charge amplifier ZET 440 for piezoelectric detectors is intended for:*amplification and conversion of output signals of primary piezoelectric transducers with charge output;*amplification and conversion of output signals of primary transducers with the IEPE type in-built electronics to voltage;*gain ratios: 1, 10, 100;*LPF: 0.1, 1, 10 Hz
-
783730-01 -
NI
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
779372-01 -
NI
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
779013-01 -
NI
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
MICRONIX
Recently, a lot of equipment have taken the high frequency or microwave technology according to the advancement and the spread of the telecommunication equipment. As a result, the handheld spectrum analyzer to analyze the signal by the frequency domain is necessaries now. The handheld spectrum analyzer is roughly classified into a heterodyne method and a Fourier transform method. The heterodyne method is also called the swept frequency method and makes it possible to measure up to tens of GHz though only for the steady signal. On the other hand, the Fourier transform method is also called the real time method and can handle an unsteady signal though the low measuring frequency range up to tens of MHz. As for our spectrum analyzer or signal analyzer, the MSA300/400 series adopts the swept frequency method, and the MSA500 series adopts both the swept frequency method and the Fourier transform method.
-
HA4600/IF -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
CG118 -
EMC Instruments Corporation
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
CPCI-SyncClock32 -
Brandywine Communications
The CPCI-SyncClock32 from Brandywine Communications provides precision time with zero latency to the host computer over the CPCI bus in the 3u form factor. An on-board microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, GPS or Have Quick.
-
Model 63-2SA -
Telebyte, Inc.
FEATURES: Full Duplex Signals; DTE/DCE Switch; TD and RD Indicators; DC to 115.2 KBPS. The Model 63-2SA provides a hardware conversion for full duplex signals between RS-232 and RS-422 I/O ports. Since the RS-232 port may look like a computer or a modem, the converter is equipped with a DTE/DCE selector switch.
-
Yokogawa Test & Measurement Corp.
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.
-
Yokogawa Test & Measurement Corp.
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.
-
Model 78663 -
Pentek, Inc.
Model 78663 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This fourchannel, high-speed A/D converter with1100 GSM DDCs (digital downconverters) accepts IF signals from an RF tuner. It is ideal for capturing all transmit and receive signals in both upper and lower GSM bands.