SCR
Thyristor, Silicon Controlled Rectifier
-
product
SCR CONTROLLED DC POWER SUPPLY
PS Series
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
product
Automated Discrete Semiconductor Tester (ATE)
5000E
Same Proven Technology as all 5000 Series Testers. High Speed Single Test Measure. Capable of Testing Multiple and Mixed Devices. 1KV Standard, 2KV Optional. 1NA to 50A Standard, 100A Optional. 0.1NA Resolution. Complete Self Test. Auto-Calibration. RDSON to 0.1MOHM Resolution. Windows Application Software. Optional Scanner. Optional Wafer Mapping. Optional Curve Trace. MOSFET, IGBT, J-FETTriac, SCR, Sidac, Diac, Quadrac, STS, SBS Transistor, Diode, Opto, Zener Regulator, MOV, Relay. UNDER $23,000.00
-
product
AdBlue & Urea Refractometer
RHA-503ABATC
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
The AdBlue refractometer RHA-503ABATC is a new hand held refractometer developed to address the growing need to check the urea concentration in AdBlue.Escalating urea prices have driven the cost of operating an SCR higher than ever before. Regretfully this has led to a new wave of problems where supplies of diluted AdBlue have found their way in to the market.Often rebranded ‘Automotive urea solution’ to eliminate the risk of prosecution by trading standards (as a mix of less than 31.8% urea cannot be labelled AdBlue). Victims of this weaker concentration may not be able to seek compensation under the Trades Description Act.
-
product
SCR CONTROLLED VARIABLE DC POWER SUPPLY
P5085C
Shown below is an AC to DC power supply with 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced to a PLC system. These units are customized units, built to order.
-
product
Test Bench For Circuit Breaker
SCR ELEKTRONIKS have developed Test Bench for Circuit Breaker to test 2, 5 & 10 at a time. Panel is provided with constant DC current source.
-
product
Test Setup For Air Conditioner
SCR ELEKTRONIKS have developed TESTING SET UP FOR SINGLE PHASE / THREE PHASE MOTOR for carrying out Performance Test, Earth Contact Resistance Test, High Voltage Test, Megger Test and Leakage Current Test. It consists of Voltmeters, Ammeters and Wattmeters for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of Earth Contact Resistance Test, HV test, Megger Test, Leakage Current Test. All tests are provided with tripping cut off concept.
-
product
Impact Test Apparatus
SCR Elektroniks make Impact Test Apparatus is used to test the Electrical Accessories / appliances for their mechanical strength.
-
product
PC Based Comprehensive Test Setup for Luminaires
Our zest for innovation has resulted in continuous upgrades in the existing line of products. Till now we used to manufacture 3 different equipments for Driver, MCPCB and Luminaires Component testing. We at SCR Elektroniks have developed our comprehensive tester to incorporate all the 3 systems in a single bench. Here in this tester one can test all the three DUT in a single bench. Since all the 3 testing procedures have many tests in common, we have incorporated all the tests in a single bench such that testing of Luminaire driver, Luminaire PCB and Final Luminaire set is performed in single test bench. Only these tests are performed over the DUT else other are disabled for them.
-
product
Calibration & Demag.
Model 8515-D
The Model 8515-D is a medium-energy, high voltage, and capacitor discharge type ringing demagnetizer capable of desaturating Ceramic and Rare Earth magnetic materials. The Model 8515-D is easily adapted to a wide range of production and laboratory demagnetizing requirements. A modern solid-state electronic control circuit, coupled with a rugged, heavy-duty discharge SCR and fixture, make this demagnetizer a highly reliable, low maintenance unit. The electronic voltage control circuit prevents the Model 8515-D from being discharged before the preset energy level has been reached, avoiding incomplete magnet desaturation. An easy to read front panel meter monitors the capacitor voltage. The energy storage level can be easily changed in the field. Integral electrical interlock and fail-safe circuitry provide a high degree of operator safety.
-
product
SCR Controller with Regulator
The SCR Controller and the Regulator Board are used in SCR controlled power supplies.CEHCO offers single phase and three phase SCR Controllers with Regulator Boards.
-
product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
High Voltage SCR Controlled Power Supply, P/N 18278PS Power Rating: 350 KW. Input: 480 VAC, 3 PH, 60 Hz Output: 0 to 5000 VDC, 70 Amps max Ripple: 2 % approximately at maximum rated voltage Configuration: 12 pulse externally SCR controlled rectifier system Protection Devices: Input contactors Overload relay shutoff Input surge suppressor Thermal switches Output current limiting resistor (made with 5 Ohm Kanthal heating element) Emergency power shutoff Cooling: Each 6 pulse rectifier assembly is cooled by three 10” fans Interface: 4/20 ma converter interface for output voltage and output current to SCR controller. Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier. Weight: Approx. 5000 lbs. SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack. Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configuration Rectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure. Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
product
Commutator Testing Unit
SCR ELEKTRONIKS have designed “Commutator Testing Setup” to provide Commutator manufacturers and users a simple and speedy method for testing their Commutators. This single station commutator testing set up therefore user can test one commutator at a time. In Automatic mode of testing this set up performs two tests automatically.
-
product
Preheating Test Setup for Hair Straightener
SCR ELEKTRONIKS have developed "60 Stations Preheating Test Setup for Hair Straightener“ for Testing of Hair Straightener. It consists of Adjustable Constant Voltage source, Digital Timer, Digital Voltmeter, Digital Timer for carrying out Heating Test of Hair Straightener. It has got the capacity to check hair straightener that require test current 28 A at different Test Voltages.
-
product
Bench Digital Multimeter, 4.5, USB, 20 A, 750 V, 0.2 Gohm
72-13625
This 72-13625 is a manual range, benchtop digital Multimeter that features 19999 display counts, large LCD screen with backlight, full scale overload protection and a unique design. This instrument can be used to measure AC and DC voltage, AC and DC current, resistance, frequency, capacitance, transistor, hFE, diode (LED), SCR, continuity, etc.
-
product
AC to AC Power Supplies, Output 0 to 25 VAC, 3000 AMPS, 75 KW, P/N 5955C
- AC to AC Power Supply, 84 KVA, 1 PH, 60 Hz, P/N 5955C- Input: 240 VAC, 350 Amps- Output: 0 to 25 VAC, 3000 Amps max- Back to back SCR is used to adjust the output voltage- Start / Stop push button- Power ON Light- Voltmeter and Ammeter are included to monitor output voltage and current- Indoor enclosure: 42″H x 32″W x 22″D- Estimated weight: (TBD)
-
product
Millivolt Drop Tester
The SCR ELEKTRONIKS Millivolt Drop Tester is an industry acclaimed product. MVDT has a specially built constant current source (current generator) up to 400A (depending on model) and a dedicated PLC to store test parameters (in automatic models), perform test procedure, make the millivolt drop & junction resistance measurements and store test results, that can be retrieved later or downloaded to PC. PC based TestWare can display the test results & export those to Office, HTML, Printer or PDF. The manual models consist of the constant current source, digital ammeter and a digital millivolt meter with 3 ranges.
-
product
SCR Controlled DC power Supplies
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single-phase or three phases. With single-phase AC input, the DC output ripple is very high (50%). With three-phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three-phase AC input instead of a single phase.
-
product
SCR CONTROLLER WITH REGULATOR
The SCR Controller and the Regulator Board are used in SCR controlled power supplies.CEHCO offers single phase and three phase SCR Controllers with Regulator Boards.Click the links below for additional details.
-
product
Advanced SCR Power Controller
Thyro-PX Series
50 years of experience are infused in the Thyro-PX® series’ design and functionality. The SCR power controller is available in single-, dual-, and three-phase units, supports voltages from 690 V and 2900 A, and offers superior interface options. Integrate operating modes and parameters seamlessly with the 2.8-inch, LED Thyro-Touch display. And enable efficient system parameters, loading, and storage via an on-board SD-card. Thyro-PX power controller is ideally suited for your transformer and resistive loads for glass, metal, and ceramic manufacturing. It is optimal for heating elements in electric furnaces.
-
product
Endurance Test Panel For Domestic Mixer
SCR ELEKTRONIKS have developed ENDURANCE TEST PANEL FOR MIXER for carrying out endurance test of mixer at final stage. It consists of Voltmeter, Ammeter, Wattmeter & Temperature Indicator for observing the values of different parameters. Output Socket is provided for quick connections and disconnections of the equipment to be tested. User friendly operations make the equipment to be handled easier for any operator.
-
product
Thermal Characterization Testing Services
Thermal Engineering Associates, Inc.
Thermal Characterization - TEA offers this service to customers having need for precise thermal parameter values for product data sheets, purchase specifications, specific application configurations, and/or device comparisons. This service is offered for a wide range of Discrete Devices (i.e., Bipolar Junction Transistors, MOSFETs, IGBTs, Diodes, SCRs, Triacs) and Integrated Circuits (i.e., digital, linear and mixed-signal devices).
-
product
Primary Current Injection Test Trolley
SCR ELEKTRONIKS have developed primary and secondary Current injection test trolley for Switchgear manufacturers for testing of ACB , MCB , MCCB. It is low Voltage high Current source with control circuitry, digital read out for test current and trip time measurement. We can select different links of CT range as per the required test Current.
-
product
4 Station Endurance Test Setup for Thermostat of Iron
SCR ELEKTRONIKS have developed 4 STATIONS ENDURANCE TEST SETUP FOR THERMOSTAT OF IRONwhich is used for carrying out endurance test for thermostat of iron for the required amount of time It is very useful and handy in line testing on Mass production line as well as type Testing. It consists of Voltmeter, Wattmeter, Programmable Logic Controller( PLC ). The equipment continuously monitors faults like Contact weld and Contact Open. The other important feature is we can operate the panel in Auto Mode or Manual mode. User friendly operations make the equipment to be handled easier for any operator. This manual contains information about operating instructions and maintenance of the equipment.
-
product
MCB Temperature Rise and Power Loss Test Bench
The SCR Elektroniks 3 station MCB Temperature Rise and Power Loss Test Bench is economically designed to verify temperature rise and measure power loss as per clause 9.8 of IEC 60898 with the circuit designed to follow test procedure as per Cl 9.8.2. The temperature rise is measured in accordance with Cl 9.8.3 and 9.8.4 while power loss is measured and verified as per Table 15 of Cl 9.8.5.
-
product
Secondary Current Injection Test Trolley
SCR ELEKTRONIKS have developed SECONDARY CURRENT INJECTION TEST TROLLEY for Switchgear items, CT manufacturer and where three phase current application is called for. It is low Voltage, 3 phase Current source with control circuitry, digital read out for test current and trip time measurement. We can select different CT ranges for each phase independently and adjust the current as per the required test Current.
-
product
Temperature Rise Test Panel
2000A
SCR ELEKTRONIKS have developed “TEMPERATURE RISE TEST BENCH FOR MEDIUM VOLTAGE SWITCH BOARDS” to measure rise in temperature at various points as mentioned in standard at junctions. The set-up consists of a True RMS Constant Current Source (to maintain the Current within + / - 1 % of set value with Digital Indication), PC based control system, Temperature data logging on PC, Servo-Controller and other indications. Digital voltmeter Primary Voltage) indicates the position of auto transformer (variac).
-
product
Fluid Property Sensors
TE Connectivity (TE) offers distinct fluid property sensor technologies to measure fluids. Our tuning fork technology is coupled with efficient software algorithms for accurate measurement of viscosity, density, and dielectric constant. Dedicated applications for our DEF sensors include oils quality sensors (engine, hydraulic, transmission), fluid monitoring, and others. Our urea quality SCR sensors, based on Ultrasonic Technology (UST), perform an analysis of the Diesel Exhaust Fluid (DEF) fluid to provide urea concentration and secure mis-filling protection to the Selective Catalytic Reduction systems. Our highly reliable reed switch technology is combined with temperature measurement for DEF level sensing.
-
product
Cord Swiveling Test Set Up For Hair Dryer & Hair Straightner
SCR Elektroniks make CORD SWIVELING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis,20 Revolutions clockwise & 20 Revolutions anti-clockwise.
-
product
MCB Instantaneous Trip Test Bench
The SCR Elektroniks MCB Instantaneous Trip Test Bench is designed for Testing of MCB to carry out “Test of Instantaneous Tripping and of correct opening of the Contacts” as per IEC: 60898-1:2002 Clause 9.10.2 at rated voltage. This test is carried out with power factor between 0.95 and 1 with the sequence operation being O-t-CO-t-CO-t-CO with timings as specified in 9.12.11.1.
-
product
SCR Diode Testers
SCRs and Diodes are used in the power sections of various power systems. A SCR Diode Tester is an important piece of equipment to determine if a SCR or a diode is defective in a power circuit. It is difficult and time-consuming to troubleshoot SCRs and Diodes with a digital meter.
