Showing results: 856 - 870 of 1109 items found.
-
CP-07 -
KILTER ELECTRONIC CO.,LTD
Can connect with Oscilloscope. AC/DC current Measurement. 400mA ,2us, 4A,2us test range. Bandwidth: DC~500kHz(-3db)Rise time:1.5μsNoise level: ≤4mA(with average mode) or ≤20mA(DC~500KHz)Jaw size: 5mm max. Auto zero at power on. Relative zero correction.
-
D9010AGGC -
Keysight Technologies
The D9010AGGC compliance test software license provides the capability to offload the measurements from the compliance test software running on an oscilloscope to one or multiple virtual machines or measurement servers. This allows you to perform continuous data acquisition and computation of tests result in parallel, reducing the overall test time.
-
CP 305 -
GMC-I-PROSyS
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
BW-AED-500 -
B&W Engineering Corp.
The input can range from 40Hz to 160KHz from sensors with similar ranges. The output can be delivered to a speaker, oscilloscope and an LED for threshold detections ranging from 0-Infinite. The power supply features regulated +5VDC, -5VDC, +12VDC, +15VDC, -15VDC and +/- unregulated 20VDC. Voltage input of 110VAC @ 60Hz or 220VAC @ 50Hz.
-
5002 -
Clarke-Hess Communications Research
The Model 5002 Phase Verification Bridge set comprises passive devices that are used in conjunction with Model 5500-2 Phase Standard and an output null indicator such as a true rms voltmeter, an oscilloscope or a wave analyzer to verify that the Phase Standard is continuing to operate within its specified phase accuracy limits.
-
Series HyperLOG ® 70 X -
Aaronia AG
Compatible with any Spectrum Analyzer or Oscilloscope. Incl. High-End Preamplifier. Ultra high gain (44dBi). The HyperLOG X LogPer antenna series can be used to locate extremely weak signals, thanks to the integrated preamplifier. The antenna offers excellent directional characteristics which can be optimized using the optional Laser and Compass.
-
DP150/DP200pro -
Powertek LLC
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
DPOJET -
Tektronix, Inc.
DPOJET is the premiere eye diagram, jitter and timing analysis package available for real-time oscilloscopes.Operating in the Tektronix DPO7000, DPO70000 and DSA70000 Series oscilloscopes. Jitter and Timing Analysis for Clocks and Data Signals. Real-Time Eye Diagram (RT-Eye™) Analysis*1. TekWizard™ Interface for One-Button and Guided Jitter Summaries.
-
WaveNode
Optional RFView output port on any WaveNode sensor (except SHF-series) allows the operator to sample coax R.F. on an oscilloscope. Connect a cable from the RFView port to your oscilloscope/spectrum analyzer for real-time RF monitoring. The output level is +13 dbm @ 1500 Watts , optimized for IMPure operation with SDR radios.
-
I3C -
Tektronix, Inc.
Tektronix I3C Software runs on Tektronix DPO/MSO5000, DPO7000 and DPO/DSA/MSO70000 oscilloscope series. I3C Software uses the hardware based real-time I3C protocol aware trigger, protocol analysis of long acquisition record length up to 125MB to provide superior I3C Protocol Analysis result at the press of button.
-
34A -
Picoprobe
Engineered to meet the stringent demands of advanced high frequency circuit designers. This high impedance probe combines full DC capability, rise/fall times of 120 ps, and a nominal loading input impedance of 10 megohm shunted by 0.1 pf. Signal attenuation is 20:1 with a 50 ohm oscilloscope input.
-
SW00MIPI -
Keysight Technologies
The MIPI Validation License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation licenses for MIPI with coverage across the MIPI technologies M-PHY, D-PHY and C-PHY. Together with the subscription model, this enables the support and coverage continuity as the MIPI technology progresses through revisions.
-
SW00DDRV -
Keysight Technologies
The DDR Validation License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation licenses for DDR with coverage across the DDR technology starting from DDR3. Together with the subscription model, this enables the support and coverage continuity as the DDR technology progresses through generations.
-
Yokogawa Test & Measurement Corp.
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.
-
Yokogawa Test & Measurement Corp.
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.