- Pickering Interfaces Inc.
product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 31.5Ω
40-252-110
The 40-252-110 is a programmable resistor module with 2 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
EHV Circuit Breaker Analyzer
DigiTMR S2
The Vanguard DIGITMR S2 is an inexpensive, easy to use digital circuit breaker analyzer. The DIGITMR S2 can be operated stand-alone or can be computer-controlled. It can fully analyze a circuit-breaker’s performance by testing the contact time, stroke, velocity, over-travel, and contact wipe. Contact and motion analysis can be performed for all breaker contact operations (Open, Close, Open – Close, Close – Open, and Open – Close – Open). Timing results are recorded and displayed on the 240 x 128 pixels back-lit LCD screen and can also be printed on the built-in 4.5″ wide thermal printer.
-
product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays ...show more -
product
PXI RTD Simulator Module 12-Channel PT1000
40-262-202
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 31.5Ω
40-252-010
The 40-252-010 is a programmable resistor module with 4 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 62.1Ω
40-251-011
The 40-251-011 is a programmable resistor module with 8 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
PXI Precision Programmable Resistor Modules
Pickering's PXI precision programmable resistor modules feature high setting resolution with excellent stability and accuracy through the use of innovative switching networks and software correction techniques. This also means all resistance values can be set - there are no missing values due to switch resistance or resistor tolerance. These modules are ideal for sensor emulation applications that require very fine adjustment and also have the capability of being set as open or short circuit to simulate faults in cabling systems. The range includes modules specifically designed for RTD and strain gauge simulation.
-
product
Trailer Light Testers
Pro-Check 725
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifie...show more -
product
C/I Tracers
Circuit Seeker Kit
*Advanced patented non-directional sensing technology*Superior sensitivity and functionality providing for accurate tracing & locating*Ergonomic receiver with information-rich full-color graphical LCD*Graphics and audible signal provide quick and easy way to understand tracing feedback*Traces concealed wiring, locates junction boxes, and finds breakers for live or open circuits
-
product
PXI RTD Simulator Module, 8 Channel, PT1000
40-263-403
The 40-263-403 is an 8-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
High Insulation Digital Clamp Tester
HCL-5000KN+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A~500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.
-
product
PXI Millivolt Thermocouple Simulators
Series 41-760
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channelseach channel providing a low-voltage output across two connector pins capable of providing 20mV with 0.7V resolution, 50mV with 1.7V resolution and 100mV with 3.3V resolution, covering most thermocouple types. These thermocouple simulators use two wire outputs with a remote output reference sense to ensure the modules deliver accurate low-level voltages, even if the system has common mode voltages present. In addition, each simulation channel is also able to provide an open circuit setting to simulate faulty wiring connections to a sensor.
-
product
Voltage Tester Pen
Shenzhen UYIGAO Electronic Technology Co., Ltd
A non-contact voltage tester is the safest way to make sure the power is off without touching any wires. Before you open an electrical box, you should: - cut off power to the outlet at the main electrical panel - confirm you turned off the right circuit This is where the non-contact voltage tester comes in handy.
-
product
50 Channel Linear Vibration Motor Aging Unit
BK2021
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
product
0.1Hz-5MHz Functional Generator
MFG-3005
*Frequency range: 0.1Hz~5MHz*Output waveforms: Sine ,triangle, square, positive and negative pulse, positive and negative ramp*Output impedance: 50Ω±10%*Output Amplitude: Not less than 20Vp-p(open circuit)*DC voltage: 0~±10V continuously adjustable*Symmetry range: 90:10—10:90*Rising edge of square: Less than 100ns
-
product
PXI RTD Simulator Module, 16 Channel, PT500
40-263-202
The 40-263-202 is a 16-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
Cable Continuity Detectors
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Cable Continuity Detector can test the open circuit, short circuit, crossover and continutiy for RJ11/RJ45/BNC/USB cable, and the test result is displayed by the visible LED light status.
-
product
Cable Fault Locator
FaultCaster
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
product
Linear Regulated Power Supplies (to 150 watts)
Gold Box "Infinity"
*Highly Configurable, with a seemingly Infinite number of Options*Any slot voltage from 1.5v to 150v is available*Remote Sensing*Open Sense protection*Isolated output*Short circuit and overload protection with enhanced surge capabilities*No minimum load required*Internal EMI Filtering*Pluggable connectors*Can be mounted on two surfaces in any orientation
-
product
PXI 16 x SPDT Reed Relays
40-110-021
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
product
Relays
Mitsubishi Electric Automation, Inc
Mitsubishi Electric offers AC and DC controlled Contactor Relays with multiple open and closed contacts configurations that can be used in a variety of applications; alarms and sensors, signal switching, detecting and controlling faults that occur in electrical circuits.
-
product
Standard Mechanical Calibration Kit, DC To 9 GHz, Type-N, 50 Ohm
85032F
The Keysight 85032F calibration kit contains precision 50 ohm type-N standards used to calibrate Keysight network analyzers. Standards include fixed terminations, open circuits, and short circuits in both genders. This kit is specified from dc to 9 GHz.
-
product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16 (female)
85038F
The Keysight 85038F calibration kit contains only female calibration devices (open circuit, short circuit and termination) and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
product
PXI RTD Simulator Module, 20 Channel, PT100
40-263-101
The 40-263-101 is a 20-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TV
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used for measurement of DCcurrent etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
product
PXI RTD Simulator Module, 24 Channel, PT1000
40-263-003
The 40-263-003 is a 24-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
Cable Length Meter
CLM1
The Cable Length Meter CLM1 will allow the accurate measurement of severed or open/short-circuit CCTV coaxial cable. For use with RG59 (75Ω) and RG58 (50Ω) or equivalent coaxial cable, this meter provides a direct readout in metres of the length of an unterminated run of coaxial cable with a resolution of 2-3 metres. A single range of 2.5 to 400 metres on a 4 digit LCD display is provided with automatic indication of open circuit and short circuit conductors. By this means, the location of a short circuit or open circuit in cable runs of up to 800 metres may be found.
-
product
ELM Electronic Load Module
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.