Filter Results By:

Products

Applications

Manufacturers

Showing results: 2191 - 2205 of 2817 items found.

  • UltraFast Gas Chromatograph

    Falcon - Teledyne Monitor Labs

    The Teledyne-Falcon Gas Chromatograph (CalidusTM) is now manufactured and fully supported by Teledyne which acquired assets of Falcon Analytical Systems & Technologies, LLC in October 2018. Along with Falcon assets, most employees now work for Teledyne, so the transition has been seamless and highly successful. To find sales and support, go to: Worldwide Sales Representatives.The Teledyne Falcon Gas Chromatograph is a fast and superior analyzer perfect for process sampling and field testing to verify consistency of materials and processes. Fence line or exhaust Benzene or VOC monitoring can be performed continuously or on an intermittent (portable) basis. The Teledyne Falcon GC paired with an FID detector will speciate hydrocarbons in a fuel sample for determining fuel quality and heating value. The simplified modular design means that a technician can swap a column or detector and perform maintenance quickly and with minimal training.

  • The Mag Lead

    136 - Electronic Specialties Inc.

    *Mag Lead features a magnetic disconnect near the test probe end. *Just disconnect the test probe and you can “stick” to any metallic ground or test point. *Quit fumbling with alligator clips that fall off - Mag Lead’s powerfull magnet will hold tight! *This is a time saving tool - if you don’t have to walk to your tool box to retrieve your alligator clips, even on just half the occasions, then you’ve saved time. *Very helpful for automotive reference points and troubleshooting. *Can eliminate the need to hold probes while checking or monitoring a signal. *Two high power, low resistance magnets hold the probe to the lead. *Fits almost all Digital Multimeters and can be used with hand-held scopes too. *Get the Mag Lead, it stays put and won’t fall off, like alligator clips do!

  • Instruments

    Lambient Technologies

    Organizations working on new thermosets or new thermoset formulations need an intimate understanding of how these materials cure before they can proceed to the next step in the research, quality control, or production process. What happens when the material is heated? When is the best time to apply pressure to squeeze out voids? How fast does the material react at 120C? 150C? 180C? Most organizations today address this need by curing a sample for an arbitrary amount of time before using inexact, error-prone manual methods, or complex thermal analytical instruments to test cure state. Maybe the sample has reached the end of cure, but maybe not. With traditional methods, it’s difficult to tell for sure. How can organizations determine whether they’re processing materials longer than necessary? Dielectric cure monitoring lets them know for sure.

  • Automatic Voltage Regulator – 1.5kVA To 3kVA

    SVR Pro - Falcon Electric, Inc

    *Convenient Rackmount/Tower Design*UL Listed for 55°C Operation in Harsh Environments*True Sinewave Output*Superior Power Conditioning*Wide Input Voltage Window*Precision Output Voltage Regulation*Superior Brownout, Surge & Transient Protection*Frequency Converter Option*Battery Backup Capability Option*LCD Display with Advanced Monitoring for Easy Remote Management*RS-232C, USB & Optional SNMP/HTTP Agent

  • In Situ Process Management

    KLA-Tencor Corp

    KLA’s comprehensive portfolio of SensArray® products enables in situ monitoring of process tools’ environments. With wired and wireless sensor wafers and reticles, an automation package and data analysis systems, SensArray products provide comprehensive information for a wide range of wafer and reticle processes. Wafer process equipment manufacturers, IC manufacturers and reticle manufacturers use SensArray data to visualize, diagnose and control process conditions.

  • Field-installation Type Residual Chlorine Meter (Four-Wire Transmission, Water flow beads)

    HR-200 - HORIBA, Ltd.

    HR-200 is connected to a residual chlorine sensor (RA-20), which allows the free residual chlorine concentration to be measured with high accuracy. It is sutable for waterworks, pool water sterilization, and desalination systems. The measurement method is a three-pole polarographic method, which enables continuous monitoring of residual chlorine concentrations without using reagents. Stable measurement over a long period was realized by physical polishing cleaning using beads.

  • Breakout Box

    T1000-15 - Tesuto Systems

    T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of  30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.

  • Electrosurgery Analyzers

    Fluke Biomedical

    Electrosurgery Analyzer is the ESU tester you can depend on for complete preventive maintenance and electrosurgical device safety to completely test these critical functions:* Measures current, voltage and power output.* Tests RF leakage from output to ensure no hazardous currents are present.* Performs Return Electrode Monitoring (REM) tests.* Measures crest factor.* Performs automatic power distribution curve at a wide range of test loads.

  • Route Based Vibration Data Collector

    Crystal instruments

    The Crystal Instruments CoCo series are portable devices for vibration monitoring and predictive maintenance applications. The system consists of a CoCo analyzer and the Engineering Data Management (EDM) software. The CoCo is used to make field measurements and the EDM software in Vibration Data Collector (VDC) Mode is used to setup the CoCo hardware and define routes before field measurements, and to download data from the CoCo to analyze and archive afterwards.

  • Power Line Transducers

    Meco Instruments Pvt. Ltd.,

    Current Transducers measure AC Current and converts it to an industry standard output signal which is directly proportional to the measured input. These Transducers provide an output which is load independent and isolated from the input. The output can be connected to Controllers, Data-Loggers, PLC''''s, Analog / Digital Indicators, Recorders for display, analysis or control. They are ideal for SCADA, Energy Management, Telemetering for Remote, Local as well as Central Monitoring Systems.

  • Frequency Monitor with Filter

    SD037 - Synectic Electronics

    Synectics’s SD037 dynamically monitors mains frequency.  The filter  enables high speed, high accuracy, frequency monitoring even with high levels of harmonic noise.   The SD037 is highly prized in demand side energy management and the associated battery storage technologies. The unit monitors the frequency of a mains voltage signal and reports the value, on demand, via an RS232, RS485 using either simple ASCII commands or Modbus protocol.

  • 3U CompactPCI® Subsystem with 13-slot Backplane, 2 + 1 CompactPCI® Redundant Power Modules

    cPCIS-2633 Series - ADLINK Technology Inc.

    *3U CompactPCI® backplane with 12 peripheral cand slots and one system slot*2 + 1 hot swappable 500 W + 250 W CompactPCI® Power supply (supports three 250 W PSUs)*Temperature, voltage, and fan monitoring LEDs*Supports current sharing on +5V, +3.3V, and +12V*PICMG® 2.11 47-pin power interfaceHot-swappable cooling fans & filter

  • Customer Acceptance Test Panel

    TA-65 - Tech-Aid Products

    DGS-65 Customer Acceptance Panel for both testing and trouble- shooting. We have added an option to the panel that allows you to select an analog slaving meter or the LED monitor lights as shown in the maintenance manual Fig. 5-14. The addition of the meter provides the technician with a more visible means to monitor the slaving "trend". The 50 pin DG connector is broken out on the panel to assist in monitoring or isolating unit signals.

  • Automatic Engine Balancing Technology

    AutoBalance™ System - Windrock, Inc.

    Continuously adjusts fuel flow to each power cylinder to maintain balanced operationMinimize emissions and fuel consumption over a wide range of operating loadsReduce mechanical wear and maintenance costsReduce personnel costs and risk by eliminating manual engine balancingSupports engines with up to 20 power cylindersOn-Guard Diagnostic software for monitoring, analysis, reporting and trendingSupports automated air manifold pressure control for minimum emissions at varying loads

  • ARINC BusTools Software Analyzer

    Abaco Systems Inc

    BusTools-ARINC is the only solution for Bus Analysis, Simulation, Maintenance and Data Logging of ARINC 429, 575, 561/6-wire, 717 and CSDB databus protocols. Simultaneously control, log and display data from a single Windows-based program on USB, PCI, CompactPCI, PCI Express, ExpressCard, PC/AT, PC/104 and PCMCIA platforms. BusTools-ARINC provides comprehensive monitoring, data logging and simulation for 100% bus loading activity.

Get Help