-
product
sbRIO-9236, Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781580-01
Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
product
Quad Op-Amp Loop
QOAL400
The QOAL400 module is a precision instrument capable of measuring all common parameters of an Op Amp, including AC as well as DC parameters. The QOAL400 has four completely independent channels, which allow a quad device to be tested in a minimum amount of time. Each channel has a full set of resources to measure all common parameters.
-
product
SparkFun GPS Dead Reckoning Breakout
NEO-M8U (Qwiic)
The SparkFun NEO-M8U GPS Breakout is a high quality GPS board with equally impressive configuration options. The NEO-M8U takes advantage of u-blox's Untethered Dead Reckoning (UDR) technology. The module provides continuous navigation without needing to make any electrical connection to a vehicle, thus reducing cost of installation for after-market dead reckoning applications.
-
product
NI-6585B , 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
784060-01
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
product
Modbus Analog Output Modules
DAT3020 Series
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
product
SATA Solid State Drive (SSD) Modules; 1TB TLC
FM8
SATA Solid State Drive (SSD) Modules (FM8) is a plug-in SATA drive compatible for use with NAI single board computers and multifunction I/O boards where a direct SATA interface to a processor is supported. The FM8 module has a capacity of 1TB in a triple-level cell (TLC) construct.
-
product
PCIe Gen3 X16 Bus Expansion Via Dual X8 OCuLink
PCI125
The PCI125 is VadaTech’s 4th generation PCIe expansion module based on the PCI-SIG specification. The Module has a Retimer/Conditioner to improve signal integrity for enhancing system performance and reliability across long cables. It removes both random and deterministic jitter from the input signals eliminating inter-symbol interference and resets the output jitter budget. It supports the full 16 lanes.
-
product
PXIe-4310, 16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module
784813-01
16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module—The PXIe-4310 is a channel-to-channel isolated, filtered analog input module for higher voltage measurements. The module offers the ability to select an analog filter per channel to provide extra filtering performance. You also can operate up to four different input ranges per terminal block and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI-DAQmx driver simplifies hardware configuration and measurement.
-
product
Receiver, 9025, 25 Module, with Slide Mounting Kit
310104387
The 9025 is a 25 module receiver compatible with all standard VPC 90 series modules and contacts and includes a locking handle to ensure proper ITA engagement. Includes mounting flanges and instrument bracket. Requires slide kit, not included.
-
product
PXI 12-Slot BRIC Matrix, 374x8 1-Pole (17 sub-cards)
40-562B-321-374X8
The 40-562B-321-374X8 is a high density BRIC12 matrix module with a size of 374x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
VME Module
COM-1553B-3
The COM-1553B board gives the MIL-1553B designer an intelligent and versatile solution to multiplexed serial data bus design requirements. In applications that require the throughput and reliability of 1553B communications, the COM-1553B is a cost-effective system component with unsurpassed performance.
-
product
PXI 4 Slot BRIC 55x16 1-Pole (5 sub-cards)
40-562A-021-55X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass
40-860A-112
The 40/42-860A-112 is a PXI/PXIe single insert/bypass switch with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI 8 Slot BRIC 360x8 2-pole (12 sub-cards)
40-561A-122-360X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
160 Pin DIN 41612 Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 160-pin DIN 41612 connector.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm - SPST
40-294-131
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI-2565, 16-Channel, 7 A, SPST PXI Relay Module
777754-01
16-Channel, 7 A, SPST PXI Relay Module—The PXI‑2565 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It delivers high-current switching of DC power supplies, AC line power, and AC/DC current sources. The PXI‑2565 is fully software programmable and supports multiple instrument synchronization.
-
product
Solar Panel Large Walk-in Chambers
EWSX282
ESPEC's solid construction walk-ins are desirable for testing large loads of PV modules or panels at 85°C/85% as well as humidity-freeze and temperature cycling tests. Hermetically welded seams and stainless-steel interior ensure integrity under extreme conditions required by IEC.The models come in different performance versions, depending on your application. More powerful performance allows you to complete the temperature-cycling test faster, or with a maximum number of modules. There also is a 'damp-heat' only model that saves you capital-cost and energy.
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 510 Ohm
40-294-014
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 40GHz, 50Ω, SMA-2.9, External Termination
40-781A-522
The 40-781A-522 (PXI) and 42-781A-522 (PXIe) are dual SPDT 40GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Built-in Measuring Instruments
PeakTech Prüf- und Messtechnik GmbH
Practical built-in module as voltmeter with freely definable measuring range from 0 to 200mV, 2V, 20V, 200V or 500 V. Current measurements from 0 to 200µA, 2mA, 20mA, 200mA and 2A can be carried out via a shunt. With the snap-in frame, this inexpensive module can be integrated into any front panel of your own construction.
-
product
2-Ch 3.6 GHz or 4-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - 6U VPX
Model 58841
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with two 3.6 GHz, 12-bit A/D- Two-channel mode with four 1.8 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverter)- 10 GB of DDR4 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optiona...show more -
product
Serial (RS-232/422/485) Module for Multi Protocol 4000 Boards
Serial Module for Multi Protocol 4000 BoardsNOTE: The M4KSerial module is now a Legacy product. All new projects should use the M4KSerialPlus module (these modules are not compatible)
-
product
Multichannel Voltage Output D/A Converters
Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the avai...show more -
product
PMC Modules
ARINC 429
Sycos range of ARINC 429 PMC modules offer the user up to 32 channels on a single width PMC module. Each channel can be programmed independently to operate at either high or low speed. Firmware options available for Tx Error Insertion and Rx Error Reporting are available.
-
-
product
PXIe Power Relay Module, 16xSPST, 16 A, With Interlock
42-161A-001-HI
The 40/42-161A-001-HI is a PXI/PXIe 16xSPST power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
product
PXI 8 Slot BRIC 920x4 1-Pole (10 sub-cards)
40-560A-121-920X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
ITA, G12, Front Mount, 12 Module With Protective Cover
410104322
The G12 ITA can be used with all G12 Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 16-Channel, 4-Pole
42-614D-012
The 40-614D-012 (PXI) and 42-614D-012 (PXIe) 2-bank, 16-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
