-
product
Manual Oscillators
MOS-01, -01A
The MOS-01 manual oscillator module is used as a quality, general-purpose sinewave oscillator and digital readout monitoring system in the MAC-01, -02, or -03 AC Power Sources/Frequency Converters. The unit has guaranteed operating range of 20 HZ to 20 KHZ which is covered in three one-decade scales. The LCD digital metering system is switch-selectable to readout either frequency, voltage or current. A toggle switch selects the input for the attached AC Power Source/Frequency Converter to origin...show more -
product
High Flexible Inline AXI Platform
AXI X# Series
The X#-platform series is an inline automated X-ray system which covers a wide range of AXI applications. It is a flexible platform with very versatile fields of use depending on the application requirements. The inspectable applications range from component level inspection for wire bonds, large SMT boards, high-power electronic modules up to fully assembled modules.
-
product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 58620
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Two DUC (digital upconverters)- Four 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
PXI High Density Multiplexer, 1-Bank, 160-Channel, 1-Pole
40-615A-011
The 40-615A-011 is a 1-bank, 160-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
PXIe-6386, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785926-01
PXIe, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6386 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6386 is ideal for a variety of applications, such as IF digitizati...show more -
product
PXI Microwave Transfer Switch, Dual, 26.5GHz, 50Ω, SMA
40-782B-532
The 40-782B-532 (PXI) and 42-782B-532 (PXIe) dual transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 26.5GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
3U VPX Flash Storage Module
Curtiss-Wright Defense Solutions
The 3U VPX (VITA 46 and 48.2) Flash Storage Module (FSM) provides high-performance, high-capacity, solid-state SATA storage with AES-256 bit encryption using an Application Specific Integrated Circuit (ASIC) that is FIPS-140-2 validated (Certification #1472). The 1" pitch conduction-cooled solid state storage device utilizes high reliability SLC NAND flash designed for the most demanding application.
-
product
PXI Very High Density Mux 49 Ch 4 Pole
40-670A-022-49/4
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
Grain Inspector
iS-G1
The iS-G1 is a full line speed optical module for the inspection of crystal grains.Using our new grain imaging technology, the iS-G1 is able to inspect as cut wafers at full inline speed with no need to stop the conveyor belt. Automated algorithms analyze the grains and report metrics.
-
product
COM Express Boards
COM Express is a highly integrated Computer On Module. It can be considered as a component (integrated circuit) in more complex designs.
-
product
PXI 12-Slot BRIC Matrix, 484x4 2-Pole (11 sub-cards)
40-562B-322-484X4
The 40-562B-322-484X4 is a high density BRIC12 matrix module with a size of 484x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Dual DC Electronic Load
3330F Series（40W~250W）
3330F Series Dual DC Electronic Load is a two load unit in one module. Each 3330F Series module has its own control and display panel, CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be remote controlled via RS232、Ethernet、USB and GPIB interface.
-
product
PXI Programmable Resistor Module
PXI Programmable Resistor Modules are wellsuited for simulating environmental conditions in hardwareintheloop(HIL) validation. The software included provides a simple user interface that accepts inputs in units of temperature or resistance, and configures the resistance across each channel. Each module uses a 37pin DSUB connector on the front panel, as well as a 2x2 MicroFit connector for easy connection to a PXI Digital Multimeter(DMM).
-
product
37-Pin D-Type Male Right Angled PCB
40-963-037-RM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Intelligent 16 Bit Data Acquisition
CPCI-AD16
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
-
product
Conduction Cooled XMC Interface Board with PCI Express Host Interface, Supporting up to 4 PX Modules, 2 RTx 5 Channel Modules, 1 Discrete & 1 Serial Module
EXC-8000ccXMC
The EXC-8000ccXMC is part of Excalibur’s 8000 family of multiprotocol boards. This conduction cooled XMC interface board has a PCI Express host interface and supports up to 4 Px modules, 2 RTx 5 channel modules, 1 Discrete and 1 Serial module. Due to the constraints of the XMC specification the modules are integrated onto the board itself rather than as physically separate modules.The EXC-8000ccXMC supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from modules that support DMA, with much less CPU overhead than when not using DMA.
-
product
16 Channel, 1 Form A 15A Relay Switch
DP-cPCI-4545
The DP-cPCI-4545 is a 16 channel relay switch module. It is constructed using 1 Form ‘A’ relays. It provides 500V DC isolation between channels.
-
product
PXI 2A Multiplexer, 2-Bank, 16-Channel 4-Pole
40-614-012
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Sensor Conditioning Data Recorder
DTX-6017SSC/HV
The DTX-6017SSC/HV series of data acquisition systems provide wideband, low noise sensor signal conditioning with embedded filtering, digitization and data recording direct to 4GB of SDRAM locate on each DTX-6192 module. System level recording rates are no longer limited by chassis throughput, bus bandwidths or long term disk storage speeds. A comprehensive user GUI running on the embedded Windows OS can be used locally with the addition of a user keyboard, mouse and video terminal, or run remotely via the integrated Ethernet connection.
-
product
Imaging Luminance Meter
CX1000
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
CX-1000 imaging brightness meter is used to measure the brightness, brightness distribution and uniformity of LED modules, lamps, lamps, displays, street brightness and other light sources.
-
product
24-Bit Precision Load Cell Input Card
PCI-9524
The PCI-9524 is a robust, multi-purpose module designed for turnkey material test systems (MTS). Equipped with four strain gauge-based transducer input channels, four general purpose analog input channels, and a 3-axis motion controller, the PCI-9524 delivers a complete hardware solution for MTS manufacturers. The PCI-9524 easily integrates physical quantity measurement and implements strategy of close-loop control in a single module package. For transducer measurement, the PCI-9524 supports sensitivity from 1.0 mV/V to 4.0 mV/V and provides a 1/200000 accuracy of measurement of full scale. These features make the PCI-9524 suitable for precise measurement in large-scale transducers.
-
product
PXI Attenuator Modules
Programmable RF Attenuators – accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices.Solid State Programmable RF Attenuators – available in triple or hex formats with bandwidths between 10MHz and 6GHz.High Voltage Attenuators – provide a convenient way of attenuating high voltage low frequency signals to levels that can be captured by other PXI devices without risk of damaging them.
-
product
Front Panel Interfacing Kit: M9018A And M9019A
Y1270A
The Y1270A Front Panel Interfacing Kit for M9018A and M9019A PXIe chassis provides a rugged interface to the front panel connectors of modules installed in the chassis. The frame is provided with a semi-transparent cover which provides additional protection for front panel cables and connectors.
-
product
Receiver, 9025 VXI, 25 Module, C-Size Interlocking
310104127
This 25 module VXI Receiver allows use of 12 pre-wired interconnect adapters. It hinges down for direct access to the instruments and is equipped with a locking handle to ensure all contacts are engaged. A standard integrated microswitch shuts off power when the ITA disengages from the receiver.
-
product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
product
PXI/PXIe Microwave Relay, Triple SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Failsafe
42-780B-753
The 40-780B-753 (PXI) and 42-780B-753 (PXIe) are triple failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
PXI BRIC8 2Resource Distributor, 4Bus Matrix
40-569-124
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
product
Ophir Power Amplifiers
Ophir RF power amplifiers are rugged and reliable. They are available as complete rack mounted units incorporating power supply, fans and heatsinks, or as compact modules requiring a DC supply. Fans and/or heatsinks can be included if required.
-
product
ITA, G6, 6 Module, Oversized Backshell
410104732
This oversized backshell for the G6 ITA features an adjustable cable exit that can accommodate cable bundles up to 2.50". To accommodate cable exit size variations, excess shield material may be snapped off via a perforated design.This backshell also allows for an increased bend radius which is necessary for many wiring configurations including high speed due to larger wire sizes.Compatible with p/n's 310104318, 310104336, and 310104344 and the G6 ITA is backwards compatible with the G6X Receiver (310104481).
-
product
sbRIO-9225, Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780588-01
Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The sbRIO‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three sbRIO‑9225 channels. Non-enclosed modules are designed for OEM applications.
