-
product
Quad Industry Pack Carrier
PCI-4pack
The PCI-4pack module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-4pack is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc.Custom application software can be downloaded to the DSP via the PCI bus. Windows 95 and WinNT drivers are standard.
-
product
3-Channel PXI Function Generator
41-620A-003
The 41-620A is a compact 3-channel function generator provided in a PXI 3U single-slot module and is fully backward compatible with our 41-620-003 module. It is capable of generating sine waves to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. This module can generate arbitrary waveforms loaded into the internal 256k memory, allowing the function generator to emulate many waveform types, including the typical waveforms of automotive and aerospace sensors.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-155
The 40-297A-155 (PXI) and the 42-297A-155 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 43.8 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Single SP6T MUX 40GHz 50Ω SMA-2.9
40-784-041
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
NI CAN Single Termination, High-Speed/FD Cable, 2m
192017-02
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
product
SMARC
ROM-5780
Advantech ROM-5780 SMARC 2.1 Computer-on-Module is powered by Rockchip RK3399 SOC which includes dual-core Arm Cortex-A72 and quad-core Arm Cortex-A53 processors and Arm Mali-T860MP4 3D graphics engine. It provides rich display interface: HDMI 4K@60Hz, eDP and LVDS to meet different requirement. It also features USB3.0, PCIe 2.0, SATA, Gigabit Ethernet, MIPI-CSI for embedded applications. It is the ideal solution for POS, vending, infotainment, Medical.
-
product
PXI/PXIe Microwave Multiplexer, Single SP8T, 18 GHz, 50 Ω, SMA, Failsafe
42-788-021
The 40-788-021 (PXI) and 42-788-021 (PXIe) are single failsafe SP8T 18 GHz unterminated microwave multiplexers. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T configurations with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
product
PXI/PXIe 15W Programmable Resistor Module
42-254-011
The 40-254-011 (PXI) and 42-254-011 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 61Ω with 0.25Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
Measurement
Multichannel Strain Gauge Meter
The Software Multichannel strain gauge meter is used for performing all types of strain gauge measurements using strain gauge sensors (for instance, force and torque sensors, bridge and semi-bridge circuits based on resistive strain sensors), strain measurement data acquisition modules ZET 017-T and digital strain gauge sensors of ZETSENSOR series. The program enables simultaneous processing of up to 128 measuring channels using strain gauge station and up to 500 measuring channels in the case if digital sensors are used.
-
product
3U VPX High Speed Video/Data Processing Card
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
product
NI-9203, 200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
783731-01
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module - The NI‑9203 is intended for high-performance control and monitoring applications. It features programmable input ranges and variable connectivity options. To protect against signal transients, the NI‑9203 … includes a channel‑to‑earth ground double‑isolation barrier (250 Vrms isolation) for safety and noise immunity.
-
product
PXI Single 4 Channel Mux Fibre Optic LC
40-850-414
The 40-850-414 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
AIM Interface Modules
AIM’s innovative, unique and successful ‘Common Core’ hardware design set new standards for onboard intelligence and performance when introduced to the market in 1998. Since then, further generations and evolutions of the Common Core approach have been introduced, offering improved performance, higher channel density, lower power consumption, the migration to smaller form factors as well as the support of new avionics bus and network communication standards.
-
product
Chassis - up to Sixteen 8x1 Modules, Thirty Two 4x1 Modules or Any Combination or Configuration of 8x1's, 4x1's, 2x1's and 2x2 Modules
CXAR/128-MF
These Chassis controls up to sixteen 8x1 modules, thirty two 4x1 modules or any combination or configuration of 8x1's, 4x1's, 2x1's and 2x2 modules. LEDs on the front panel show switch and power status. Add Switch Modules, CP8 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
-
product
IP / Ethernet Testers
Anritsu's powerful Ethernet/IP network data analyzers incorporate the dual functionality of wire speed performance analysis and network monitoring in the same instrument. Multiple protocols can be decoded and displayed for captured Ethernet, SONET, or SDH frames at full wire speed up to 100 Gbps, augmented by an optional Decode Module and Expert Analysis Module.
-
product
Standard Voltage 37 Pin D-Type Connectors for Pickering
The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.
-
product
GMCT RF Connectors For Pickering Products
The connectors below are suitable to use with Pickering cards and modules that utilize a GMCT RF connector.
-
product
Removable Storage Unit
PXI-DM-U.2
The PXI-DM-U.2 PXI Express Storage Unit provides up to 15.36 TB of removable NVME solid state storage (SSD) in a single PXI Express slot. The storage module addresses the requirements of users who need to remove and replace PXI Express storage for security, archival or other reasons.
-
product
Circuit Module, Riser for ISMB, PCIex4 to 3PCIex1 A101-3, RoHS
AIMB-R4301-03A2E
- Connecting Interface: PCIe x4- Expansion Slots: 3 PCIex1
-
product
COM Express Type 6 Prototyping Kit based on Intel® 12th Gen Core™ i5-12600HE
COM Express Type 6 Alder Lake-P
The cExpress-BT is a COM ExpressR COM.0 R2.1 Type 6 module supporting the Intel Atom® processor E3800 Series and Intel® Celeron® N2900/J1900 processor SoC (codename: Bay Trail). The cExpress-BT is specifically designed for customers who need high-level processing and graphics performance with low power consumption in a long product life solution.
-
product
Embedded MXM GPU Module with NVIDIA® Quadro® Embedded RTX3000
EGX-MXM-RTX3000
The EGX-MXM-RTX3000 module features advanced NVIDIA® Turing™ GPU technology in MXM 3.1 Type B form factor. It’s compact, slim and reliable design makes it suitable for mission critical environment. With Quadro® Turing™ TU106 processing cores, EGX-MXM-RTX3000 supports 4 DP1.4 displays offering a flexible and easy solution for medical and gaming applications.
-
product
sbRIO-9881, Non-Enclosed, 1-Port C Series CANopen Interface Module
785966-01
The sbRIO‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The sbRIO‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The sbRIO‑9881 is compatible with only CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
product
Squid PCI Express Carrier Boards™ for MiniPCI Express Modules
Amfeltec Squid PCI Express Carrier Boards™ for MiniPCI Express Modules
-
product
Analog & Digital Audio Analyzer
FX100
The FX100 is a unique professional audio analyzer that adapts to your application. The instrument offers comprehensive measurements including Passed/Failed tests in under 1 second. You may customize the system for two or four parallel channel operation, speaker impedance testing and digital audio measurements. Switcher modules provide additional outputs and inputs.
-
product
0.3Hz-6MHz Amplitude Display Functional Generator
MFG-8306
Features:*Max. frequency up to 15MHz*Single-chip function generating module provides high stability and low distortion waveforms*5 digit frequency display, 3 digit amplitude display.*Built-in frequency meter for testing external signal up to 20MHz*Linear and Logarithmic sweep function.*AM/FM function optional(Models with suffix “A”)*5W Power Output function optional(Models with suffix “W”)
-
product
Signal/Micro Power/Micro Coax, Module, ITA, i2 MX, TriPaddle, 9/9 Position
510144004
Signal/Micro Power/Micro Coax, Module, ITA, i2 MX, TriPaddle, 9/9 Position.
-
product
Additional hardware for our test systems
REINHARDT System- und Messelectronic GmbH
Our test systems are made up of modules which can be added to the needs of our customers.
-
product
Amplifier Module
LNAM-LPA
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
product
Xeon D-15xx SoC Processor AMC
AMC754
The AMC754 is a Processor AMC in a single module, mid-size, based on the Intel® 5th generation Xeon 4-core, 8-core or 16-core Processors (Broadwell). The efficient SoC design has low power consumption and integrated PCH technology. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 62.1Ω
40-251-111
The 40-251-111 is a programmable resistor module with 4 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.