Showing results: 976 - 990 of 4131 items found.
-
8800 Series -
Venable Instruments
The analyzer utilizes a digital “Sync” signal to provide synchronization between analog and digital hardware. The Model 8800 performs simultaneous analysis on both analog input channels and digital target processor, reliably capturing all data. Versatile by design, the Model 8800 digital interface can be disabled, via software, to use the analyzer in a standard 2-channel, analog-only configuration.
-
Models CLK4 & CLK6 -
Laurel Electronics, Inc
4-digit model (CLK4) with HH:MM display, or 6-digit model (CLK6) with HH:MM:SS display. Large-digit displays with a digit height of 2.2" (57 mm), 4.0" (102 mm), 5.7" (144 mm), 7.9" (200 mm), or 11.0" (280 mm) for long viewing distances. Optional relays and data I/O. Choice of display brightness and cases for indoor or outdoor mounting.
-
Traction Wheel Assembly -
Electro-Sensors, Inc.
The complete and ready-to-install system converts linear travel/speeds to square-wave pulses/frequencies. • Square-wave frequency output, NPN open-collector • 5-28 VDC powered • 1 to 1,270 pulses per revolution (PPR - specify when ordering) • Optional bi-directional (quadrature) output models • 3 models: black neoprene rubber, smooth polyurethane, and diamond knurled aluminum tread
-
Vektrex Electronic Systems
The Vektrex SpikeSafe DC Current Sources provide reliable drive for LED/laser diode reliability, IESNA LM-80 test, and other current-driven test applications. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, precise current, and high power density — typically 6.4kW-8kW.
-
370 -
Lake Shore Cryotronics, Inc.
The Model 370 AC Resistance Bridge is designed for precise, accurate, low noise, low excitation power AC resistance measurements. Its primary application is the measurement of resistive materials in cryogenic environments from 20 mK to 1 K. Fully integrated, the Model 370 includes features to reduce and control noise at every step of the resistance measurement process
-
TE2504 -
Ajinkya Electronic Systems
Ampere Hour Meter Module- Model TE 2504 is basically managed for ready setup or the usage can be seen in where the current requirement are low. This one is used which is ready to be applied in the stand alone panel and advanced from all the former models, IM2501, IM2502 and IM2503. These are basically panel mount instruments which are required to rectified in the rectifier or in an independent panel.
-
480 -
Lake Shore Cryotronics, Inc.
An advanced tool designed primarily for use in industrial and measurement systems settings, the Model 480 Fluxmeter measures total flux from which B, flux density, and/or H, magnetic field strength, can be determined. The Model 480 is valuable for magnetizing, manual and automated magnet testing and sorting, and as the main component in BH loop or hysteresis measurement system applications.
-
4014 -
Red Phase Instruments Australia Pty Ltd.
The Model 4014 integrates four ammeters for the direct and simultaneous reading of C.T. secondaries up to 10A during the setting up or checking of protection systems while they are in service with normal 50/60Hz primary currents flowing. The two terminals of each channel of the Model 4014 are connected in series with the C.T. secondary with all other equipment in the loop or directly across the C.T. secondary.
-
40-491-001 -
Pickering Interfaces Ltd.
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
40-490-002 -
Pickering Interfaces Ltd.
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
40-491-002 -
Pickering Interfaces Ltd.
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
9554-( ) -
Solar Electronics Company
Utilizing the high voltage power source in the Model 9354-1 Universal Transient Generator, four individual modules can be connected to provide tuning of damped sine waves from 10 KHz to 50 MHz. A fifth module is available which, when used in conjunction with the Model 9354-1, provides 20% frequency steps from 30 MHz to 100 MHz
-
3077A -
TSI Inc.
Aerosol Neutralizer 3077A has five times the activity of the Model 3077. The 3077A is offered for general-purpose applications involving highly charged aerosols and low flow rates. It is supplied with our Model 3034 Scanning Mobility Particle Sizer™ (SMPS) spectrometer.Features and Benefits Radioactivity of 370 MBq Maximum flow rate of 5 L/min Kr-85 source
-
E36313A -
Keysight Technologies
The 160-Watt E36313A is a clean reliable bench power supply for general purpose applications. It combines convenient benchtop capabilities with flexible system features in a compact intuitive package. This is one of three models in this product family. The E36312A (80 W)offers the same feature set with reduced power and the E36311A (80 W) is the most economic model with reduced feature set.
-
Pacer Instruments
The model T-506 Digital Thermometer kit is a high performance, reliable, portable, easy to use unit for a low reasonable cost.