Showing results: 31 - 45 of 48 items found.
-
FLIR QL320 -
Teledyne FLIR
The QL320 is a quantitative optical gas imaging (QOGI) system that allows surveyors to measure the leak rates for methane and other hydrocarbons. This eliminates the need for secondary sampling with a toxic vapor analyzer or similar tool. In addition, the QL320 does not require close contact with the gas in order to measure emission rates, making it a safer solution for quantifying difficult-to-measure gas leaks.
-
Seitron
Seitron designs and manufactures detectors for methane, LPG, gasoline vapours and carbon monoxide (CO) for commercial and process industry use. Our detectors provide three communication protocols 4..20mA, Modbus and S-Bus (a proprietary protocol derived from Modbus). You can also choose between two types of housings: polycarbonate for industrial use or ATEX-certified for the installation of detectors in ATEX-classified areas.
-
General Tools & Instruments
A leak of natural gas (methane), propane or butane can cause an explosion in a basement with a sloppily installed unit as easily as it can in a coal mine. General sells these life-saving combustible gas detectors in various shapes and sizes, including pens and wands with a probe. Two models, the NGD268 & PNGD170 Combustible Gas Detectors even work from -40 to 158F, the extreme environment typical of mines and tunnel construction.
-
Model N901 -
Teledyne Advanced Pollution Instrumentation
The Model N901 is a near-continuous hydrocarbon gas analyzer that measures the concentration of Methane (CH4) and Total Hydrocarbons (THC) in air. The concentration of the non-Methane (NMHC) component is calculated by the subtraction of CH4 from THC, with high sensitivity and accuracy. The hydrocarbons are measured using a Flame Ionization Detector (FID), in combination with gas chromatography (GC). The instruments range and performance are tuned specifically for use in ambient air quality monitoring assessments.
-
Extech EZ40 -
Extech Instruments Corporation
The Extech EZ40 EzFlex Combustible Gas Detector has a 16 inch gooseneck for easy access into hard to reach locations. Detector has a high sensitivity and a one hand operation with thumb controlled sensitivity adjustments to eliminate the background gas levels. It has a visible and audible alarm at 10% (LEL) lower explosive limited for methane. This gas detector will help you locate the smallest leaks. Complete with 3 C batteries.
-
PLGA-1000 -
HORIBA, Ltd.
The PLGA-1000 Process Laser Gas Analyzer is designed to measure hydrocarbons and other gases contained in process gases at petrochemical plants. The PLGA-1000 uses proprietary technology to measure low concentrations of acetylene (C2H2) and carbon dioxide (CO2) contained as impurities in high concentration methane (CH4) and ethane (C2H6) which are material gases, continuously at high speed and with high sensitivity . This contributes to improvements in productivity, cost, and quality in the manufacturing process, as well as reducing environmental impact.
-
GSD600 -
Amprobe Test Tools
The Amprobe GSD600 Gas Leak Detector is a fast responding gas leak detector for methane and propane gas. The meter emits a frequency tone when gas is detected. The frequency of the beep coincides with the concentration of the gas. The LEDs display the level of gas present in an area or room. Pinpoint gas leaks for closed piping systems. Use the mute function in quiet work areas and utilize the LED displays. Or a standard earphone jack for hearing the meter in loud environments.
-
PCE Instruments
In the diverse PCE range you will find an oxygen meter for water and gases. We have available an oxygen meter for water for both pure oxygen content and for oxygen concentration. The oxygen meter for water and gases has a water resistant design, interface and internal data memory as well as the classical version for laboratories. The oxygen meter for gases follows the security norms and is used for detection and measurement of methane, hydrogen sulfide, carbon monoxide and oxygen (as well as 50 more gases).
-
VA-5000 (Siloxane) -
HORIBA, Ltd.
VA-5000 Series Siloxane Analyzer continuously measures siloxane concentration in gases with high sensitivity. It is tunable according to the type of cyclic siloxane to be measured. It is also available to measure carbon dioxide and methane at the same time as siloxane. The system can be used for siloxane durability testing of contact parts such as relays and motors, impurity monitoring and fuel quality control in biogas power generation facilities, and many other needs.
-
NevadaNanotech Systems, Inc.
NevadaNano’s Molecular Property Spectrometer™ (MPS™) Flammable Gas sensor is powering the next generation of combustible gas detection. The MPS delivers unprecedented reliability, accuracy, and worker safety by simultaneously detecting over a dozen of the most common combustible gases, including Hydrogen, Methane, Propane, Butane, and many more. We call this TrueLEL™. No other flammable gas sensor can accurately report 0-100% LEL across over a dozen different gases with just one factory calibration, the MPS never requires field calibration.
-
FLIR GF620 -
Teledyne FLIR
The FLIR GF620 is the first high-resolution, handheld camera from FLIR to detect methane and other volatile organic compound (VOC) emissions. With its ground-breaking 640 x 480 resolution IR detector, inspectors can check thousands of components and safely scan for gases from greater distances. It's also the first FLIR OGI camera to offer Quantification mode (Q-Mode) for streamlined set-up of the optional QL320 gas quantification system.
-
PCE Instruments
Here you will find gas analyzers that meet industry standards relating to personal safety and that are mainly used to detect and measure levels of methane, hydrogen sulphide, carbon monoxide, oxygen and 50 other gases. The auto-calibration function allows for easy calibration. Some of them also possess the ability to store values and can later transfer data to a computer. One accessory is the manual aspirator, with this device, you can draw gas directly into the analyzer via a 2 m long tube with which you will be able to measure gas levels without having to be in direct contact to the gas source or to be able to determine the levels of gas in places that are difficult to access.
-
Oxygas 500 -
Teledyne Gas & Flame Detection
The Oxygas 500 compliments the Gascoseeker 500 with a similar performance, measuring % LEL and % volume flammable hydrocarbons, but with the addition of oxygen for either gas/air or gas/nitrogen/air purging. The Oxygas 500 has the following additional features; automated zero during start-up, manually selectable purge mode.The P-500 variant has an additional part per million (ppm) range of methane.The Oxygas 500 is easy to use with very simple training, as the operation of the instrument follows the operation of the purge cycle. The rugged design allows the Oxygas 500 to be used in harsh environments. The instrument is also fully compatible with our range of calibration software and equipment.
-
PCE Instruments
At PCE Instruments you will find a professional quality gas detector / gas detection instrument for everyday use. The gas detector meets the requirements for personal safety and issued mainly for the detection of methane, hydrogen sulphide, carbon monoxide and oxygen levels (along with 50 other possible gases). The auto-calibration function allows for easy recalibration of the gas detector. Depending on the model, the gas detector has the ability to store data and later transfer recorded values to a computer.One accessory is the manual aspirator, with this device you can draw gas directly into the gas detection instrument via a 2m long tube with which you will be able to measure gas levels without having to be in direct contact with the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a fixed installation gas detector in many different models available.
-
PCE Instruments
At PCE Instruments you will find a professional quality gas meters for everyday use. The gas detector meets the requirements for personal safety and issued mainly for the detection of methane, hydrogen sulphide, carbon monoxide and oxygen levels (along with 50 other possible gases). The auto-calibration function allows for easy recalibration of the gas detector. Depending on the model, the gas detector has the ability to store data and later transfer recorded values to a computer.One accessory is the manual aspirator, with this device you can draw gas directly into the gas detection instrument via a 2 m long tube with which you will be able to measure gas levels without having to be in direct contact with the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a fixed installation gas detector in many different models available.
