Filter Results By:

Products

Applications

Manufacturers

Meters

sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.

See Also: Sensors, Measurement


Showing product results. 4621 - 4635 of 5025 products found.

  • Socket Tester with RCD Tripping

    Shanghai Beihan Electronics Co., Ltd.

    *Mains wiring polarity check.*ELCB/RCD testing.*Measuring ear for line current.*Measuring ear for leakage current.*Helps calculate insulation resistance.*Helps calculate power consumption.*Helps fault finding of standing earth fault.*Fused main adapter.*Appliance testing (with the ad of a clamp meter).

  • Carbon Pile Load Tester 500 AMP

    6034 - Associated Equipment Corp.

    • Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported

  • Reverse Test Probe

    I-Stop - Trilithic Inc.

    The I-Stop Reverse Test Probe is a test accessory designed for use with most signal level meters and with the Trilithic 9580 Return Maintenance System. Screw the probe into a distribution tap's unused KS port and a spring-loaded "stinger" connects a 20 dB resistive test point circuit to the hardline.

  • Loss Test Set, Return Loss Test Set

    LTS1315, LTS1315R - KD Optics Ltd.

    The KD Optics LTS1315 is a combined mains / battery powered laser source and power meter designed to make attenuation testing in the field easy, reliable and most importantly, consistent. The LTS1315R incorporates return loss measurement (RLM) capability with the ability to switch very easily between dBrel and return loss.

  • Optical Light Source

    STC-OLS201 series - Shanghai Stone Communication tech Co., Ltd

    a simple and cost-effective fiber optic tester,it is usually used together with fiber optic power meter to measure the optical loss on fiber cables. STC-OLS201 series light source provide multiple wavelength output, the wavelengths can be required on customer specific requirements (the Max wavelength is 5, such as 850/1300/1310/1490/1550nm).

  • Restoration Contractor's Kit

    Extech MO280-RK - Extech Instruments Corporation

    The Extech MO280-RK Restoration Contractor's Kit is a complete solution for the restoration contractor. This kit uses pins and pinless meters to better diagnose the amount of moisture content in a certain material. The thermal hygrometer provides a fast and accurate reading of ambient room conditions and GPP calculations. This kit is a supplied in a rugged hard carrying case. Kit includes the MO280 Pinless Moisture Meter which displays 0 to 99% moisture from a selection of 10 different wood types. The measurement surface depth is 0.75 of an inch with virtually no surface damage. MO220 Wood Moisture Meter comes with integral pins and a remote pin probe that displays up to 99.9% of the moisture level with 8 different wood types with calibrations for approximately 170 wood species. Kit also includes the RH490 Precision Hygro-Thermometer which has a 2% RH accuracy and a fast 30 second RH response time. Measures humidity, temperature, dew point, wet bulb, GPP and g/kg. The Extech MO280-RK Restoration Contractor's Kit also includes the RHT10 Humidity and Temperature USB Datalogger that records up to 16,000 readings each of RH and temperature. The USB interface and software is included in the kit.

  • Automatic Relay Test Set

    DRTS 66 - Altanova Group

    DRTS 66 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 6 Current and 6 Voltage generators simultaneously available.

  • Automatic Relay Test Set

    DRTS 34 - Altanova Group

    DRTS 34 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 4 Voltage generators simultaneously available.

  • Automatic Relay Test Set

    DRTS 33 - Altanova Group

    DRTS 33 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 3 Voltage generators simultaneously available.

  • Automatic Relay Test Set

    DRTS 64 - Altanova Group

    DRTS 64 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 6 Current and 4 Voltage generators simultaneously available.

  • Dual Temperature

    Fieldpiece Instruments, Inc

    The Fieldpiece Dual-Temperature Accessory, model ATH4, measures two temperatures simultaneously using the included k-type, wrap tab beaded thermocouples. The technology inside the ATH4 provides superior temperature compensation in rapidly changing environments commonly found while performing field service. Use the ATH4 to find Delta T and just about any temperature split you want to measure. Displays T1, T2 and T1-T2 on your Fieldpiece meter, handle or data logger. It is included with the HVAC Guide® System Analyzer to get target superheat and for the Target Evaporator Exit Temperature test. Fieldpiece offers a wide variety of k-type thermocouples for various HVAC specific applications. Use pipe clamp T/Cs with the ATH4 to check for blocked filters.

  • Garmin LIDAR-Lite V4 LED

    Distance Measurement Sensor (Qwiic) - SparkFun Electronics

    The LIDAR-Lite v4 Qwiic from GARMIN is a high-performance, wireless optical distance measurement sensor that doesn't require any soldering to get started. This is the ideal solution for drone, robot, IoT, or unmanned vehicle operations when space is tight and power is limited. This sensor has up to a 10 meter range, 1cm resolution, and requires 85mA during data acquisition. The user can read and write to the LIDAR-Lite v4 using the I2C protocol; this is where the addition of the SparkFun Qwiic system really shines. The LIDAR sensor requires 5V to operate but runs on 3V3 logic. With a 5V boost circuit and an easy-to-use Qwiic connector you can power the sensor and get distance measurements over Qwiic all with a single piece of hardware.

  • Instrument Grade Data Sensor

    WISER 8000 - TECAT Performance Systems, LLC

    The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 has a long range data transmission of >1,000 meters with up to +/- 0.025% FSR sensitivity for remote measurements. After initial setup using the WISER software interface, the system can be wired directly to your DAQ system, for seamless data collection.

  • Linear regulated power supply with thyristor pre-regulation

    NTN - FuG Elektronik GmbH

    High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units

  • OTDRs and Fault Locator

    AFL

    AFL optical time domain reflectometers (OTDRs) and fault locators are used to certify new fiber installations and locate faults in deployed fiber optic networks. OTDRs and fault locators are available for both multimode and single-mode networks, including FTTx PONs. OTDRs scan fiber optic networks from one end of the fiber, displaying a trace and reporting detected events such as splices, connectors, micro- or macro-bends and fiber end. Fiber length is reported along with location, loss and reflectance of detected events. Several OTDRs are available with an integrated visual fault locator (VFL), optical light source (OLS), and/or optical power meter (OPM). OTDR results can be saved and uploaded to PC for further analysis and/or archiving.

Get Help