Showing results: 4381 - 4395 of 4774 items found.
-
Extech 871515 -
Extech Instruments Corporation
The Extech 871515 is a Type-K general purpose temperature probe that can accurately measure temperatures from -40°C to 700°C (-40°F to 1292°F). The probe is 100 mm (4 in) long, 3.2 mm (0.126 in) in diameter, and is attached to a 1 m (39 in) cable with Type-K mini connector, so it is compatible with any meter that supports Type-K inputs. The Extech 871515 comes with a 6-month warranty.
-
Extech 407744 -
Extech Instruments Corporation
This 1kHz, 94dB professional sound calibrator for 0.5" or 1.0" microphones calibrates and verifies sound level meter operation. Battery test position with battery status LED indicates if battery is good. Durable die-cast aluminum housing generates a 1kHz sine wave at 94dB to an accuracy of 5% (frequency) and ±0.5dB (94dB). Meets IEC standard 60942 1997-11. Complete with two 9V batteries, carrying case, and screwdriver.
-
Extech 392050 -
Extech Instruments Corporation
The 392050 is a Penetration Stem Dial Thermometer that has a temperature range of-58 to 302 Degrees F (-50 to 150°C) and an accuracy of +/-2 Degrees F. Ideal for use in liquids, semi-solids, and solids. It features a 5-Inch stainless steel shaft with a 2-Inch dial, an On/Off switch, and Auto power off after an hour. Meter includes 1.5V battery button and protective plastic sheath with pocket clip.
-
Extech CA3018 -
Extech Instruments Corporation
The Extech CA3018 is a 3000A AC flex clamp-on adaptor for multimeters and clamp on meters with standard sized banana plugs. The CA3018 is an 45.7 cm (18 in) flexible clamp capable of measuring AC Currents up to 3000 A. Complete with built-in flex clamp cable, 2 m (6.6 ft) lead with banana plugs, and two AAA batteries. UL listed with a CAT IV 600 V safety rating.
-
Extech CA3010 -
Extech Instruments Corporation
The Extech CA3010 is a 3000 A AC Flex Clamp-on Adaptor for multimeters and clamp on meters with standard sized banana plugs. The CA3010 is a 25.4 cm (10 in) flexible clamp capable of measuring AC currents up to 3000 A. Complete with built-in flex clamp cable, 2 m (6.6ft) lead with banana plugs, and two AAA batteries. UL listed with a CAT IV 600 V safety rating.
-
FRANKONIA GmbH
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
Siborg Systems Inc
LCR-Reader-MPA combines tweezer probes with a powerful LCR/ESR-meter that is able to determine the type of component and best test parameters before measuring with a 0.1% basic accuracy. The device will display the main impedance value, any secondary values such as ESR, Q or D, component type and test parameters used instantly on a bright backlit LCD display. The 1 oz. device is very portable and ideal for fieldwork.
-
1044A -
The Eastern Specialty Company
Due to overwhelming demand, TESCO is pleased to re-introduce the 1044A 20 Amp Current Transformer Burden Test Set. This light weight, hand held unit is a simple and inexpensive means whereby a current transformer installation may be quickly checked for many sources of trouble. The 1044A provides utilities a less expensive and more traditional option for checking larger services for potential meter circuit related issues.
-
6410 DM -
Standard Electric Works Co., Ltd
● 3000 counts with a maximum display of 2999.● Angled display design helps the user to identify the reading of value easier.● Auto scanning function for AC/DC voltage, and current.● Auto ranging.● Range change function.● Continuity check.● Diode & Capacitance measurement.● Data hold function.● Low battery indication.● Over range indication.● Fuse protection.● Special hook design used to hang the meter for ease of use.
-
E9320 Series -
Keysight Technologies
- Operates with the EPM-P series and P-Series power meters- 300 kHz, 1.5 MHz and 5 MHz video (modulation) bandwidths- Provides peak and average power measurements- Calibration factors stored in EEPROM- Fast measurement speed over the GPIB (up to 1,000 readings per second)- Two frequency ranges: 50 MHz to 6 GHz, and 50 MHz to 18 GHz- Wide dynamic range sensors
-
LA-1 HC -
Walter G. Legge Company Inc.
LA-1 HC Floor Conductivity Tester Hand Crank is an easy-to-use meter developed for accurately testing the conductivity of floors and equipment. The LA- 1 must be used regularly to monitor proper conductivity with NFPA code # 99. Regular use of the LA-1 will establish and maintain procedures for the proper maintenance of conductive floors, eliminate fire hazards, and provide a static free environment. A hand crank AC type generator provides a rectified DC test potential. Additionally, there are no brushes to wear out. The LA-1 has an easy-to-read scale that is selectively expanded electronically to assure accurate readings over the entire range of the instrument and the scale has a length of 3.75. This is 42% longer than typical competitive testers. The LA-1 uses 500V DC to test the resistance (in ohms) between two points. (NFPA Code #99) The meter comes ready-to-use (tin foil must be applied to bottom of weights). Simply follow the instructions for use and instantly obtain an accurate measurement. Choose electric or hand powered model.
-
Energy Gear -
Ducati energia S. p. A.
Datalogger web gateway for energy monitoring. with data reading from energy meters, pulse counters and different sensors , data logging on internal memory , data transmission to web cloud or to local server or PC. Communication via intranet, internet or 3G cellular line.It’s intended for the energy management of industrial plants, office branches, companies with wide geographical distribution, unattended facilities of production plants or services, Energy Service Company
-
AJIT Electronics Co.
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
Perten AM5200 -
Calibre
The AM5200 is a bench top moisture meter providing moisture and specific weight measurements in just 10 seconds. The high frequency technology penetrates deep into samples, providing more accurate analysis, regardless of temperature or crop type. This particular machine draws upon Perten’s extensive research and development with over 1,000 different types of grain moisture testing equipment, to offer unmatched analysis in terms of accuracy, repeatability and reliability.
-
R4K-36 Series -
MATSUSADA Precision Inc.
R4K-36 series is the most compact power supply among the family of ultra compact bench-top DC supply, RK series. In addition to its impressive compact size, 4-digit voltage and current meters make circuit testing easier. With capability of digital interface, it is also ideal for production line of electrical components and for quality inspection. R4K-36 is an innovative power supply, and more than just an ordinary DC regulated supply.
