Filter Results By:

Products

Applications

Manufacturers

Meters

sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.

See Also: Sensors, Measurement


Showing recent results 4006 - 4020 of 4471 products found.

  • Long Range Cooled Thermal Sniper Sight

    ThermoSight® HISS-XLR - Teledyne FLIR

    The ThermoSight® HISS-XLR clip-on thermal weapon sight allows snipers to detect and recognize man-size targets in excess of 2,000 meters, an increase in engagement range of more than 25% compared to previous models. Designed to mount on any MIL-STD-1913 rail interface forward of an existing scope, HISS-XLR can interface with a wide range of day scopes and weapon platforms. Long-range optics coupled with an HD display provides crisp imagery, and portrait orientation compensates for bullet drop at extreme ranges.

  • Low Frequency RF Over Fiber

    RF Optic

    RF Optic’s RF over Fiber modules (RFoF) are suitable for telecommunications, satellite, radio telescopes, distribution antennas, broadcasting audio and video, timing synchronization and GPS applications. For example, point-to-point antennas can be connected from several meters to many kilometers away from the control room by fiber cables; Base stations can be connected through fiber to remote sector antennas; Satellite antennas can be connected through fiber cable to remote sites via by RF over Fiber solutions.

  • Low Input Bias Current Amplifiers (<100 pA)

    Analog Devices Inc.

    Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.

  • LTB/LTP

    SecuControl inc.

    The LTB is a test block with a deep rear end and allows easy and safe disconnection of IED's (protective relays, fault recorders, revenue meters, ...) from the system side of the power grid. The LTB typically works together with the LTP test plug which features an integrated leverage mechanism to aid with the insertion into the LTB. The sophisticated mechanical functioning of the LTP contributes to a blindingly easy plug-in process of the test plug. A large number of poles hence can be quickly disconnected with a few simple movements.

  • Maintenance & Test Equipment

    Mors Smitt Group

    The D-dock system consists of a D-dock Test Block which is put between the existing relay socket and the existing D-U plug-in relay. All 14 relay-pins are wired to the Break-Out Box enabling to connect measuring equipment like multimeters, scope meters or data analyzers to log operations during longer period. This makes fault finding easy. The D-dock fits in tightly packed relay panels and small cabinets. It can operate unattended enabling normal passenger operating service.

  • Pen-Type Food Thermometers

    Bestone Industrial Ltd.

    This thermometers look like an extra-large needle with a temperature gauge on the end. It delivers reliable results when you want accurate measurement readings of both internal and ambient temperatures. This electronic temperature meter can also be used in getting food temperatures. The probe can measure temperature that range from -50°C~ 300°C (-58 ~ 572°F). The easy-to-read digital readouts has a large screen that quickly displays temperatures in either Fahrenheit (°F) or Celsius (°C) with just one press

  • Portable Multifunction Calibrator

    M143 - Clarke-Hess Communications Research

    The M143 Multifunction calibrator is a cost saving solution for calibration of electric meters with up to 1000 V and 20 A. It offersa basic accuracy of 0.01% in DC voltage for calibration of 3 and 4 digit multimeters. The resistance function is covered byeight fix resistors in range from 10 to 100 M. The calibrator offers TC temperature sensor simulation. It can be deliveredoptionally as well with RTD temperature sensor simulator. Thanks to its small dimensions and low weight the unit can be usedeasily for field calibration work.

  • Probes

    Hygro-i Series - Tramex Ltd.

    The Tramex Hygro-i ® relative humidity probe is the most advanced, resilient and reusable RH probe on the market today. Used in conjuntion with Tramex CMEX II and MRH III moisture meters, the Hygro-i ® relative humidity probes allow the user to perform in situ and hood type RH testing to comply with ASTM F2170 and British Standards BS 8201, 8203, 5325 for the Flooring Industry, and is ideal for use by Flood & Water Damage Restoration and Indoor Air Quality professionals.

  • Pulsed and CW lasers, 375 – 1700 nm, 1 kHz measurement rate

    871 Series - Bristol Instruments, Inc.

    The 871 Laser Wavelength Meter from Bristol Instruments is the best way to measure the absolute wavelength of both pulsed and CW lasers and OPOs. By combining proven Fizeau etalon technology with automatic calibration, the reliable accuracy needed for the most meaningful experimental results is ensured. What’s more, a sustained measurement rate of 1 kHz enables the wavelength characterization of every single pulse for most lasers. And, the resulting time resolution of 1 ms provides the most detailed analysis of tunable lasers.

  • Push Pull Testers

    IMADA, Incorporated

    Lever-operated manual systems enable rapid push/pull testing up to 220 lbf.Wheel-operated manual systems enable slower, more precise movement with the hand wheel up to 750 lbf.Motorized push/pull testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement up to 1100 lbf.All push/pull testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.

  • Rangefinder

    Opti-Logic Corp.

    All of our Insight Laser Rangefinders are easy to use instruments, designed to be incorporated in a variety of different applications. With a ranging ability from 4-1000 yards (meters) depending on model, each unit allows rapid, accurate range determination of the acquired target with single touch operation in about a second giving you the opportunity to make accurate judgments for all ranging applications. Each unit displays range data using both an internal LED and external LCD simultaneously.

  • RX Family Of 32-bit High Power Efficiency MCUs

    RX600 - Renesas Electronics Corp.

    The RX600 Series has an abundant lineup of high-performance microcontrollers with up to 160MHz CPU operation, This Series offers up to 4MB of embedded Flash and 640KB of embedded SRAM, advanced security, connectivity (Ethernet, USB, CAN) and HMI function. The RX600 Series addresses a broad range of applications for IoT endpoints such as white goods, meters, and other industry and consumer area. The RX600 Series can be considered as the mainstream series of the RX Family. Some of the RX600 Series products are tuned for motor control solutions, too.

  • SAX/PAX

    SecuControl inc.

    SAX is a surface mount terminal / test block combination for interfacing substation devices (protection relays, fault recorders, revenue meters, . . . ) to the voltage and current transformers and to other equipment on the system side of a power grid. PAX is a test plug keyed to a particular configuration of SAX blocks. Once inserted into the corresponding SAX block, the PAX plug isolates the substation devices from the system side equipment while at the same time allowing connection of test equipment for secondary injection tests.

  • Surge / DC Hi-Pot Consoles

    HC Model - PJ Electronics, Inc.

    (Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.

  • Surge Voltage Generator

    SSG 1100 - BAUR Prüf- und Messtechnik GmbH

    Cable fault location with the BAUR SSG 1100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit

Get Help