Filter Results By:

Products

Applications

Manufacturers

Measurement

an acertained value.

See Also: Metrology, Instrumentation, Sensors, Meters, Stability


Showing results: 9676 - 9690 of 10608 items found.

  • Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester

    PC401 - Andor Design Corp.

    MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.

  • Triaxal Seismograph

    BC 1313 TRIAXIAL SEISMOGRAPH - ZETLAB Company

    BC 1313 piezoelectric seismographs are intended to convert vibration parameters to a proportional electrical signal. Measurements are carried out for 3 mutually perpendicular axes X, Y, and Z at a time. BC 1313 seismographs are seismic accelerometers, the parameter measured – vibration acceleration. For BC 1313 seismic transducers, the system is provided for sensing element electrical stimulation using an actuator to determine conversion ratio true value during periodic recalibration without dismantling. Power check system is also allowed for in BC 1313 seismographs.

  • Partial Discharge Testing Equipment

    3i - Scope T&M Pvt, Ltd.

    The portable multipurpose 3i device (Intellectual Insulation Indicator) is for eff ective high-voltage equipment insulation monitoring on-line. The 3i device measures and analyses partial discharges (PD). For eff ective PD measurement and noise rejection, there are two types of sensors used in the device: the acoustic sensor and the TEV sensor. Both the sensors are built into the device case, and so do not need any connection cables. The device is supplied in a strong metal case; at the faceplate there are the colored screen and two buttons: power button and function button.

  • Portable Dissolved Oxygen Meter

    Extech DO700 - Extech Instruments Corporation

    The 9-in-1 DO700 Kit measures DO concentration/saturation, pH, mV, Temperature, Conductivity, TDS, Salinity, and Resistivity. It features automatic salinity compensation and manual barometric pressure compensation for DO measurements. In addition, it has automatic one button calibration of 4, 7 and 10 pH with a choice of three-point calibration for better accuracy and it provides automatic temperature compensation. Complete with DO probe, pH/mV/Temp electrode, polymer Conductivity cell, pH and Conductivity calibration solutions, batteries and hard carrying case.

  • High Voltage Ammeter

    Ampstik®+ - SensorLink

    Use the Ampstik+ to safely take accurate current measurements when performing high voltage live-line load checks for balancing, switching, or breaking load. This high voltage ammeter measures in every electric utility setting with a linear current sensor to accurately measure .5A to 5000A, while in voltage environments up to 500kV. The opening of the amp sensor is electronically closed, while external currents are electronically rejected. This design enables the user to measure an individual conductor within close proximity to adjacent conductors without interference errors.

  • Non-Contacting Multiturn

    Bourns

    A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator. Rotary position sensors can be used in applications where a user needs to control a variable output such as a frequency, speed or volume control. Typical applications include test and measurement equipment, consumer electronics, small engines, robotics, and medical equipment.

  • Single-Functional Testers

    MI 3121 - Metrel d.d.

    The MI 3121 SMARTEC Insulation / Continuity is a tester for dead testing of electrical installations. With both an analogue and digital representation of the results, the instrument ensures accurate measurements up to 2000 Ω on continuity and up to 30 GΩ on insulation function. Configurable limits enable a PASS / FAIL evaluation of test results, which is accompanied with the bright red and green indicator lights for comfortable use even in the dark conditions. The MI 3121 is equipped with a built-in charger and has a magnetic holder in order to free up hands for testing.

  • Spot Thermal Cameras

    IRC - Martindale Electric Co. Ltd

    The combination of real time thermal imaging with spot infrared temperature measurement, packaged in a rugged pistol design, make it the ideal tool for electricians and maintenance teams needing fast on-site diagnostics. The cameras show hot and cold spots at a glance and accurately measure spot temperatures of hot and hard to reach surfaces. The advanced thermal images, displayed on the 4.5cm colour display, combine colour temperature gradients and component outlines to quickly troubleshoot problems, be it poor electrical connections, phase unbalance or faulty motors and bearings.

  • Advanced Communication Test System

    ACTS - Trilithic Inc.

    As the name suggests this new server performs a variety of tests related to cable system advanced communication services, including VoIP and high speed data. The server enables a VoIP RTP test from any field test point with or without Unsolicited Grant Service (UGS), as well as high speed throughput (UDP up to 40 Mbps max). The VoIP test enables efficient service pre-installation verification with a simple, yet comprehensive set of measurement data including upstream and downstream latency, jitter, packet loss and MOS.

  • Battery Analyzers

    BA6010 Series - B&K Precision Corporation

    The BA6010 Series battery analyzers measure voltage and resistance of modern battery technologies with high accuracy, resolution, and speed. Additionally, these instruments provide auxiliary measurement parameters inductance, capacitance, dissipation factor, impedance, quality factor, reactance, and phase angle in degrees and radians. The BA6010 Series is suitable for characterizing battery chemistries that are responsive to a 1 kHz AC stimulus signal including lead acid, lithium and alkaline type batteries used in consumer products, electric vehicles, power backup, security, and fire alarm systems.

  • ATOS ScanBox

    Series 7 - GOM GmbH

    The ATOS ScanBox Series 7 is mainly used in car manufacturing, in try-out toolmaking and in press shops. The optical 3D measuring system performs complete analysis measurements for comparison in the introductory phase or is used for quality control in production. Large parts such as automobile side panels and attached parts of up to 6 m in size can be measured. The full- field measuring data enable the analysis of hole pattern, trimming and character lines. Even heavy and large parts for other applications can be measured and inspected with the ATOS ScanBox Series 7.

  • 4-Wire Universal Cable/Harness Tester

    LX-850 - Shenzhen Lian Xin Technology Co., Ltd.

    Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V·The system adopts the advanced four-wire measurement, and the minimum measurable range is 1mΩ.·The maximum test spot is 256.·640×480 full Chinese/English large color display .·All varieties of linearity and safety tests are available.·Fully programmable continuous test is available.

  • Diode Power probe

    COMM-connect

    The COMM-connect 3026 Diode based temperature compensated probe is designed for use with the COMM-connect range of Power Monitors. The probe will handle from 50µW to 100mW . Used with external couplers and the our measurement system application from 1W to 1MW, a high dynamic range can be configured. The 3026 Diode based probe gives excellent stable results along with the COMM-connect Power Monitor variants. This gives our customers a number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.

  • DC Meters/Rail Meters:

    Bierer & Associates, Inc

    Digital DC Resistive Voltmeter has a single range of 0 – 2kV. The unit consists of a meter probe, second probe, and connector cable. This unit is designed to measure DC voltage between the negative return rail and overhead positive cantenary conductor used on transit systems. The five position selector switch located on the face, controls OFF, ON, and Test. The OFF positions are for storage and transit. The ON position is for measurements from 0 to 1999 volts with one-volt resolution. The T position tests basic meter functions and the digital display.

  • Production and Laboratory OTDR

    8000 - Photon Kinetics

    The 8000 OTDR is the first of a new generation of OTDRs that has been designed specifically for optical fiber and cable test applications. Its revolutionary "performance first" optical design delivers unsurpassed optical performance, and its MS Windows operating system facilitates integration of the OTDR into manufacturing networks. These features, combined with unique data acquisition capabilities, significantly reduce the time associated with many aspects of the OTDR measurement process, making it possible for fiber and cable manufacturers to increase production output and reduce manufacturing costs.

Get Help