-
product
sbRIO-9219, Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
781027-01
Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The sbRIO‑9219 is designed for multipurpose testing. With the sbRIO‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel. Non-enclosed modules are designed for OEM applications.
-
product
Analog and Digital Front Ends
ACQUA Front Ends
Measurement Front Ends (MFEs) convert the digital test signals of the communication analysis system ACQUA to the analog or digital formats required by terminal equipment, acoustic transducers, networks, network components, or system simulators, thus allowing complete tests in both transmission directions.
-
product
NI-9239, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
779593-01
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
product
Relative Humidity & Temperature Probe
HMP7
Vaisala HUMICAP® Humidity and Temperature Probe HMP7 is designed for applications which involve constant high humidity or rapid changes in humidity such as drying and test chambers, combustion air and other humidifiers and meteorological measurements where measurement performance and chemical tolerance are essential.
-
product
Sensor Cables
PCB® manufactures a wide variety of cable assemblies that will mate to different sensor types, signal conditioners and data acquisition systems. Cables are an important part of every measurement system. PCB carefully selects different raw cable types from trusted suppliers and time is taken to design cable to connector interfaces that will be reliable. All cable assemblies are produced at one of PCB's manufacturing locations to tightly controlled assembly procedures that ensure durability in various applications and environments.
-
product
Magnetic Field And Permeability Measurement
MAGNETOMAT 1.790
Foerster Instruments, Incorporated
The MAGNETOMAT 1.790 is a measuring system for the precision detection of magnetic flux density and relative permeability. The MAGNETOMAT software is used for displaying the measured values and saving and exporting data. The wide range of probes facilitates optimal adjustment to the conditions of the application, such as the measurement of relative permeability within the scope of the quality control of stainless steel and low-permeable (non-magnetic) alloys. Further applications include the lon...show more -
product
Ultrafast Laser Pulse Measurement
Ultrafast Laser Pulse Measurement Products by MesaPhotonics
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
USB-5133 , Oscilloscope 50 MHz Bandwidth, 100 MS/s, 2-Channel, 8-Bit USB Oscilloscope Device
780469-02
50 MHz Bandwidth, 100 MS/s, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5133 low-cost oscilloscope device has two channels that sample up to 100 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
product
PCI Analog IO Board
MS 1803
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
product
Magnet Testing
RMP Rotor Measuring Station
The RMP Rotor Measuring Station is a universal measuring system for the precise measurement and quality control of multi-pole permanent magnet rotors.
-
product
Wafer/Chip/Package Semi-automated ESD Tester
400SW
Tokyo Electronics Trading Co., Ltd.
Semi-automated ESD tester featuring Ecdm 400E, Universal ESD Simulator. Used with a manual wafer probing system or a die manipulator, wafer or die level semi-auto ESD test can be done, as well as packaged device test. Damage is detected by V-I curve or leakage current change detection. Stress level and measurement points are programmed by personal computor via GP-IB. Once test terminals are selected, ESD endurance is automatically measured.
-
product
Saluki SE4002 FET Input Preamplifier
The SE4002 is a low-noise, ultra-high input impedance preamplifier with excellent common-mode rejection. It is designed to work with any Saluki digital lock-in amplifier. The preamplifier minimizes noise and pickup in the connecting lines and reduces measurement time in noise-limited experiments.
-
product
Solid Optical 3D Measurement Instrument
IF-SensorR25
The IF-Sensor25 is a solid optical 3D measurement instrument for automated form and roughness measurement in production. The sensor is integrated into a production line and delivers you high resolution, repeatable and traceable results when measuring surface characteristics in the m or sub-m range. This resolution can hardly be achieved by conventional 2D solutions or tactile techniques.
-
product
Temperature Calibrators
Fluke Temperature Calibrators simulate process sensors for testing temperature instrumentation. Specifically designed for the field, these lightweight compact tools are EMI tolerant, dust and splash resistant and offer an easy to use single push button interface. When paired with a temperature sensor they can take high accuracy temperature measurements to verify process temperatures and ensure the highest product quality and safety. There are a variety of different temperature calibrators designed for your unique calibration and testing requirements.
-
product
Application software
The measurement equipment is controled by connected PC, and make it easy operation to analyze and management of measured data.
-
product
Standard Gain Horn Pyramidal Horn Antenna
Elva’s SGPH series of standard gain horn antennas cover the frequency range of 18 to 220 GHz in ten waveguide bands. They can be issued with rectangular or circular waveguide. Lens technology significantly allows decreasing mechanical sizes of horns and correcting beam for the best performance. These horns are ideal solution for measurement gain of other antennas, short range radars and radiometers.
-
product
RF Proximity Detector
Type RPD-2 AND Type RPD-2A
The Type RPD-2 Radio Frequency (RF) Proximity Detector is designed to detect and locate devices that radiate radio waves in the high frequency to low microwave frequency range. Such devices often include surveillance and “spy” equipment. The Type RPD-2, when used with the different sensors, will detect the emanation of the radio wave within a confined area, and then isolate its location to within approximately a square foot. The type RPD-2A may be used as an RF field strength indicator for antenna field strength measurements. The RPD-2A is identical in function except that the meter scale is calibrated in relative dB units.
-
product
Thermal Anemometers
Thermal Anemometers for the measurement of air velocity. Devices are also known as Hot Wire Anemometers, and the instruments can come with telescopic as well as articulated 90° angled probes.
-
product
Configurable System For Temperature Measurement With CAN Interface
MU thermocouple1 CAN
The thermocouple measuring unit offers connections for 8 thermocouples, which are designed for the temperature measuring ranges J, K or T, depending on the product version.
-
product
ICAP/4Windows
An extensive SPICE toolset for extensive circuit design. Includes everything for analog and mixed-signal circuits, less ICAP/4's Smith chart, Library Manager and model generation tool (SpiceMod). Contains newly enhanced analyses for advanced design verification, design pass/fail measurement capability and automated component stress alarms.
-
product
Handheld Portable Multifunction Data Logger
HD31
Three independent input channels Automatic recognition of the probes - Measurement of Temperature Relative Humidity Atmospheric and differential pressure Air Speed Illuminance (lux) and Irradiance Carbon dioxide (CO2) – Air Quality Direct voltage (VP473 module) and current (IP472 module).
-
product
Industrial Panel Controls
Panels controls are designed for applications that typically require frequent adjustment. Both rotary and slide panel control types are available. A selection of elements includes carbon, cermet, and conductive plastic. These devices are available in various sizes and shaft/bushing combinations. Some models are available with a rotary switch and seal options. Typical applications include audio mixing consoles, test and measurement equipment, consumer electronics, and medical equipment.
-
product
Automatic Test Equipment (ATE) Automatic Electrical Measurement Platform
i7000 Series
Automatic Test Equipment (ATE) Automatic Electrical Measurement Platform by ADSYS
-
product
PCI-5153, 500 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
780318-02
500 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device - The PCI‑5153 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 500 MHz of analog bandwidth and flexible measurement configurations.
-
product
SPA100
Our highly sensitive source picoammeter is designed for measuring and logging very small currents down to the pA range - making it an ideal instrument for scientific and research applications, including physics, materials science and electron microscopy. Full-featured at an affordable price, the SPA100 combines sensitivity, accuracy and stability to allow users to measure low currents with high precision as well as conveniently source bias voltages for experimentation. SPA100 also doubles as an ...show more -
product
Dynamic Signal Analysis
m+p Analyzer is a fully integrated solution for dynamic signal measurement, analysis and advanced reporting of all noise and vibration, acoustics and general dynamic signal applications. Comprehensive time and frequency analysis is available with both online and offline data processing. Complete with advanced application wizards the m+p dynamic signal analyzer makes light work of gathering data, displaying results, performing specialized analysis and generating customer ready reports – all within one user interface. m+p Analyzer is designed for noise and vibration applications in the field and in the lab.
-
product
Laser Distance Measurer
NT-8560
Ideal for measuring factory layout, facilities safety area, trench depth, roof area for solar, building maintenance, ceilings maintenance, road works, water level, sheet rock measurement.
-
product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-02
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR … test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
product
Sound Level Meter, 30 dB, 130 dB, 1.5 dB, 0.1 dB, 0 °C, 40 °C
72-942
Compact Digital Sound Level Meter measures less than 9" in length, including the windscreen, yet provides selectable response time and frequency weighting. It is perfect for sound system testing, speaker system measurement and environmental noise level monitoring.
