Filter Results By:
Products
Applications
Manufacturers
MUX
Combine multiple signals into one signal.
-
product
PXI Dual 4 to 1 RF MUX MCX 75 Ohm
40-832-102
The 40-832-102 is a 75 Ohm 4 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-832 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
Switch Modules - 16 Single or Two Pole Relays Arranged as Four Separate 4x1 Multiplexers
JX16/4(4x1)-1 and -2
This module has 16 single or two pole relays arranged as four separate4x1 multiplexers as shown in the figure. The muxes may be operated and wired individually for up to 64 4x1"s per chassis, or jumpered together to form 8x1"s or 16x1"s or jumpered to the backplane to form up to a 256x1 mux or two 128x1 muxes. It is available with Type S, M or LT reed relays.
-
product
RS232/422 Strobe Mux III Card & Panel
9565-32
32 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 14.5" high x 13" wide x 1" deep (645 x 330 x 25 mm).
-
product
PXI Dual 8 to 1 Mux 1GHz 75 Ohm SMB
40-748-751
The 40-748 is a dual 8 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-748 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
product
AS 770
MUX Module is used for combining or separating wavelength in a wide wavelength range.- CATV Wavelength Range : 1540 ~ 1620 nm- Low Insertion Loss- PON Wavelength Range : 1260 ~ 1500 nm- High Isolation
-
product
PXI High Density Multiplexer, 94-Channel, 1-Pole
40-640A-022-94/1
The 40-640A-022-94/1 is a 94-channel, 1-pole MUX and is part of a series of high density multiplexer modules featuring a choice of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI High Density Screened MUX 47-Ch 1-Pole
40-640-021-S/47/1
The multiplexer module is available as a 47-channel 2-pole, 94-channel 1-pole or 47-channel 1-pole with screened relays. Connections are made via a front panel 96-pin connector.
-
product
PXI 3A Power MUX BRIC, 32-Channel, 6-Pole
40-571-404
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PCI Very High Density Multiplexer, 10-Channel, 16-Pole
50-670C-022-10/16
The 50-670C-022-10/16 is a 10-channel, 16-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode
40-850A-314
The 40/42-850A-314 is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
High-Density PXI Multiplexer Switch Modules
This range of High-Density Multiplexer Switch Modules provides a compact array of MUX solutions with differing combinations of channel counts and poles. Most of our high-density solutions include isolation relays that allow the MUX to be disconnected from the single input/output port, enabling the convenient interconnection of other channels.
-
product
Single 2 Channel Fibre Optic Mux SC/PC
40-815-212
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 50Ω, SMB
42-874A-002
The 40-874A-002 (PXI) and 42-874A-002 are 50 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
PXI/PXIe MEMS Optical MUX, Quad 2-Channel, Single-Mode, 9/125 Fiber, LC Connectors
42-855A-442
The 40/42-855A-442 is a PXI/PXIe quad 2-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
PXI 3A Power MUX BRIC, 10-Channel, 24-Pole
40-571-105
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PCI 2 Amp Multiplexer, Dual 4-Channel, 4-Pole
50-635A-107
The 50-635A-107 is a dual 4-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI Solid State MUX, 20 bank, 8 channel
40-680-001
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated, 3GHz, 50Ω, MCX
40-873A-102
The 40-873A-102 (PXI) and 42-873A-102 (PXIe) are 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
PXI Very High Density Multiplexer, 99-Channel 1pole
40-670C-021-99/1
The 40-670C-021-99/1 is a 99-channel, 1-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
PXI Single 18 Channel MUX, BNC Connectors
40-735-902-S3
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
Dual 2 Channel Fibre Optic Mux Multi Mod
40-815-122-M
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
Single 2 Channel Fibre Optic Mux FC/APC
40-815-012
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, MCX
40-835A-101
The 40-835A-101 (PXI) and 42-835A-101 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode
40-852A-018
The 40/42-852A-018 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PCI 2 Amp Multiplexer, Single 32-Channel, 1-Pole
50-635A-101
The 50-635A-101 is a single 32-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI Dual 4 to 1 Terminated RF Multiplexer 3GHz 50 Ohm MCX
40-873-102
The 40-873-102 is a 4 to 1 RF MUX with 2 banks in a single PXI slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
PXI/PXIe RF Multiplexer, Single 6-Channel, Terminated, 8GHz, 50Ω, SMA
40-881B-001
The 40-881B-001 (PXI) and 42-881B-001 (PXIe) are single 6 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. It is available as a single or dual MUX in one and two slots respectively.
-
product
PXI/PXIe RF Multiplexer, Quad 4-Channel, 3GHz, 75Ω, MCX
40-832A-104
The 40-832A-104 (PXI) and 42-832A-104 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
RF R-PHY Video Engines
ATX’s RF R-PHY video engines provide a mux pass-through function that enables cable operators to maintain existing video encryption functionality on in-service edge QAMs, alleviating the need to migrate encryption functionality to the CCAP video core during early stages of DAA transition. ATX RF R-PHY video engines also relieve MSOs of undertaking back-office system integration to reconfigure and manage muxes and broadcast lineups in CCAP video cores. For MSOs considering an accelerated transition to IPTV, the ATX RF R-PHY Video Engine provides a low-cost and low-complexity alternative to implementing a CCAP video core.
-
product
PXI/PXIe RF Multiplexer, Quad 4-Channel, 3GHz, 50Ω, SMB
40-872A-004
The 40-872A-004 (PXI) and 42-872A-004 (PXIe) are 50 Ohm 4 to 1 RF multiplexers available with 4 banks in a single PXI slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
