Showing results: 61 - 75 of 79 items found.
-
ROM-DB3900 -
Advantech Co. Ltd.
ROM-DB3900 is an evaluation carrier board designed for the Advantech RTX2.0 module. It is compatible with the RTX2.0 module ROM-3420 and has a rich I/O interface for evaluation and development. It supports wide range operating temperature, and also supports two MIPI connectors for a camera module. ROM-DB3900 is an ideal development board for ruggedized applications, such as industrial control, automation control and HDMI systems.
-
E-CAM30_HEXCUTX2 -
e-con Systems Inc.
e-CAM30_HEXCUTX2 (HexCamera) is a multiple camera solution for NVIDIA® Jetson TX1/TX2 developer kit that consists of six 3.4 MP 2-Lane MIPI CSI-2 camera board and an adaptor board (e-CAMHEX_TX2ADAP) to interface with the J22 connector on the Jetson TX1/TX2. Each camera is based on the camera module e-CAM30_CUMI0330_MOD, 1/3" AR0330 color CMOS image sensor from ON Semiconductor® and integrated high performance Image Signal Processor (ISP). All these six cameras are connected to the e-CAMHEX_TX2ADAP adaptor board using 30 cm micro-coaxial cable.
-
Framos Technologies d.o.o.
FRAMOS is the first company in the market to integrate Analog Devices’s new GMSL3 technology into an embedded vision environment. GMSL3 can transmit high frame rates (4K, 90 fps) as far as 14 meters with unprecedented efficiency. This interface is well suited for applications where the MIPI CSI-2 (D-PHY) length restrictions are not sufficient, while at the same time, a highly durable cable with low power consumption and low cost are essential. Camera developers can use the flexible FRAMOS Sensor Module Ecosystem to validate a variety of image sensors in the lab and in the field while taking advantage of the interface’s features.
-
e-CAM21_CUMI290_MOD -
Sensory Analytics
The e-CAM21_CUMI290_MOD is a 2 MP ultra-lowlight RAW MIPI camera module with the S-mount (M12) lens holder. This FHD camera module is based on SONY IMX290, one of the most popular Sony's STARVIS® CMOS sensor. SONY IMX290 is a 1/2.8" rolling shutter CMOS sensor with 2.9µm pixel size. Its effective pixel back-illuminated technology with improved sensitivity in the visible-light and near infrared light enables customers to capture images even in absolute darkness. The e-CAM21_CUMI290_MOD can stream uncompressed FHD @120 fps in 10-bit mode and 60fps in 12-bit mode.
-
e-CAM21_CUMI290_MOD -
e-con Systems Inc.
The e-CAM21_CUMI290_MOD is a 2 MP ultra-lowlight RAW MIPI camera module with the S-mount (M12) lens holder. This FHD camera module is based on SONY IMX290, one of the most popular Sony's STARVIS® CMOS sensor. SONY IMX290 is a 1/2.8" rolling shutter CMOS sensor with 2.9µm pixel size. Its effective pixel back-illuminated technology with improved sensitivity in the visible-light and near infrared light enables customers to capture images even in absolute darkness. The e-CAM21_CUMI290_MOD can stream uncompressed FHD @120 fps in 10-bit mode and 60fps in 12-bit mode.
-
ROM-DB5900 -
Advantech Co. Ltd.
ROM-DB5900 is an evaluation carrier board designed for the Advantech SMARC module. It is compatible with SMARC module ROM-5420 and has a rich I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and also supports two MIPI connectors for the camera module. ROM-DB5900 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems.
-
ROM-DB5901 -
Advantech Co. Ltd.
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
E-CAM130_TRICUTX2 -
e-con Systems Inc.
e-CAM130_TRICUTX2 (TRICamera) is a multiple camera solution for NVIDIA® Jetson TX2 developer kit that consists of three 13 MP 4-Lane MIPI CSI-2 camera board and an base board to interface with the J22 connector on the Jetson TX2. Each camera is based on the camera module e-CAM137_CUMI1335_MOD, 1/3.2" AR1335 color CMOS image sensor from ON Semiconductor® and integrated high performance Image Signal Processor (ISP).
-
ICE40 LP/HX -
Lattice Semiconductor
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
E-CAM31_TX2 -
e-con Systems Inc.
e-CAM31_TX2 is a 3.4 Mega pixel 4-lane MIPI CSI-2 liquid lens Auto focus camera board for NVIDIA® Jetson TX2 developer kit and it is also compatible with NVIDIA® Jetson TX1 developer kit. This camera is based on 1/3 inch AR0330 CMOS Image sensor from ON Semiconductor® with 2.2 µm pixel and A-Pix™ technology and an integrated high performance image signal processor (ISP). This S-Mount (M12) liquid lens camera enables autofocus with no mechanical moving part like VCM (Voice Coil Motors) will increase the lifetime and has an ability to focus and refocus in a matter of milliseconds.
-
PGY-SPMI-EX-PD -
Prodigy Technovations Pvt. Ltd.
SPMI Protocol Analyzer (PGY-SPMI-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. SPMI (System Power Management Interface) is a MIPI (Mobile Industry Processor Interface) standard with 2-wire synchronous serial, bidirectional interface that connects the integrated Power Controller(PC) of a System on- Chip (SoC) processor system with one or more Power Management Integrated Circuits (PMIC) voltage regulation systems.
-
e-con Systems Inc.
e-con Systems Camera Modules come with parallel & MIPI interfaces. Our CMOS camera modules will be effective in any application or environment because of their versatility and wide range of options. Embedded camera module can be interfaced to processors like Tegra K1, i.MX6, DM3730, OMAP. Further to these HD camera modules, e-con offers evaluation boards with these camera modules interfaced to various development boards featuring these processors. We provide Omnivision Camera Module & Aptina Camera Module (ON Semiconductor) with CMOS Sensors.
-
E-CAM21_CUTX2 -
e-con Systems Inc.
e-CAM21_CUTX2 is a 2MP Ultra-Lowlight 4-lane MIPI CSI-2 camera board for NVIDIA® Jetson TX2 developer kit. This camera is based on 1/2.8" SONY IMX290 CMOS Sensor, one of the most popular Sony's STARVIS® sensor. Its effective pixel back-illuminated technology with improved sensitivity in the visible-light and near infrared light enables customers to capture images even in absolute darkness. This Starlight Camera uses NVIDIA® on-board Jetson TX2 Image Signal Processor (ISP) to perform all the Auto functions (Auto White Balance, Auto Exposure control) and significantly, improved image quality. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
Teledyne e2v
Teledyne e2v has developed compact MIPI modules which feature our own high performance CMOS image sensors inside a pre-focused, industrial-grade scanning optic. As a turnkey sensor/optics for imaging systems, these modules offers customers significant reduction in development time and cost savings. Only a few screws are needed to mount the module, with simple connection to the image processing system through an FPC cable connector. Software development efforts can also be reduced by using some limited API-layer Linux software drivers. This enables the module to be seamlessly interfaced to popular ISP platforms.
-
Analog Devices Inc.
HDMI® receivers and DVI receivers remain in high demand for professional, consumer, and automotive video applications, with HDMI nodes constantly increasing. Analog Devices offers a range of HDMI/DVI receivers that enable high quality conversion of digital video data to formats such as HDMI, MIPI, and TTL. Applications include video distribution, gaming, and HDMI/DVI consumer device connectivity for automotive infotainment systems. Our portfolio of HDMI receivers and DVI receivers offers competitive advantages such as automotive qualification, superior HDMI/DVI equalizer performance, comprehensive audio extraction, and small packages (6 mm × 6 mm, 0.5 mm pitch BGA).
