-
product
Drivetrain Tester
G5.DT
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
product
PXI 20 x SPST 10 Amp Power Relay Module
40-160-003
The 40-160 module has a choice of 10 x SPST, 20 x SPST or 10 x DPST Power Relays, suitable for switching inductive/capacitive loads up to 10A at 250Vac.Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.It is suitable for applications requiring switching of either mains voltage or DC current.
-
product
Vibration / Shock / Noise & Thermal Control
We specialise in vibration damping and shock isolation solutions for electronics and other light load applications.Our soft gel vibration damping materials are designed for isolating very light componets and extreme temperature environments.Most of our products are held in stock to support engineers with urgent vibration damping, noise control, shock isolation and cushioning impact problems.Our shock and vibration solutions are currently in use in aerospace, rail, truck, bus and handheld applications.
-
product
PXIe-4051 - PXIe, 1-Channel, 60 V, 40 A PXI Electronic Load Module
788179-01
The PXIe-4051 provides programmable load capable of sinking DC power for characterization, design validation, and manufacturing test. This module helps you sink current and absorb power out of a power source up to 300 W with programmable constant voltage, current, resistance, and power levels. You can use the PXIe-4051 to streamline the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and semiconductor component test—by eliminating the need to mix multiple instrumentation form factors in a given test system and simplifying synchronization.
-
product
Personal Workstations for Load Ranges up to 440 lbs.
9200 Series
The 9200 Series Vibration Isolation Workstation is a smaller, more compact design providing affordable personal convenience. The 9200 is ideal for applications such as Balances, Optical Microscopes, Cell Injection, Roundness Checkers, and Surface Profilometers.
-
product
DC Electronic Load
3310G Series（800W）
Has its own control and display panel, CC / CR / CV / CP / Dynamic modes, with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface
-
product
PoE Tester
PE-100
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotat...show more -
product
Meter Test Bench
Meter Test Banch is available with high-technology to ensure high testing accuracy as well as maximum functionality. It is designed to provide precise results in any simple to complex testing. It comes with modern systems to ensure to provide artificial load that cannot be changed in the power supply. It is provided with high durability and efficacy to ensure long lasting life with no maintenance. In addition to this, it ensures high accuracy in testing without any wear.
-
product
Signal Conditioning With SLSC
Switch Load and Signal Conditioning standardizes the "last mile" between the measuring device and the device under test (DUT) in hardware and software. SLSC is a modular extension for data acquisition products such as PXI and CompactRIO.
-
product
LED Power Driver ATS
8491
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optio...show more -
product
Load/Force/Torque Sensor
Load cells and force sensors engineered and manufactured by Stellar Technology can be found in industrial applications all over the world. These include market sectors such as aerospace, oil & gas, automotive,
-
product
High-Speed Impact Testing Machines
HITS-X Series
With the increasing demand for safety and reliability, evaluation of the dynamic strength (impact properties) of materials and parts is becoming more and more important. This machine can obtain data, such as the maximum test force, energy, and displacement, up to a maximum velocity of 72 km/h (20 m/s). A tensile load type (HITS-TX) and a punching type (HITS-PX) are available.
-
product
PXI General Purpose 2A Relay Module 16xSPDT, 78 D-sub
40-131-101
Low cost, general purpose electromechanical relay cards suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include switching of medium power AC and DC loads or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 or 78 pin D-Type connector plug.
-
product
300W to 504W - Single Output
iQG Series
*Standard Quarter Brick Footprint*36-76 Vdc Inputs*9.6, 12 Vdc Outputs*1500 Vdc Isolation*Baseplate Cooled*94.5% Typical Efficiency*Droop Load Share Option
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Battery Extra Load Units
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with an...show more -
product
Through Hole/ Donut Load Cell Compression Only
THC SERIES
Our THC Series through hole donut load cells offer an outside diameter of 2.00 inches and up to six different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Auto Elmendorf Tear Tester
TF140C
TESTEX Testing Equipment Systems Ltd.
It enables rapid determination of the dynamic resistance of materials designed to be subjected to strong shearing loads (e.g. fabrics) or liable to be damaged by sharp or heavy objects (e.g. paper bags). Subsequently, the test was naturally adopted for all materials in the form of sheet or films, cardboards, cloth, knitted fabrics, plastic films, aluminium foil, non-woven fabrics, complex flexible packaging etc.
-
product
PXI 5A MUX, 1-Bank, 48-Chan, Ind. Isolation
40-651-101
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
Software Packages
GLUON
The software uses notched specimens (CT specimens) to evaluate the material elasto-plastic fracture toughness value (JIC). The test is conducted at constant loading rate under test-force control or CTOD control and the load is removed to calculate the crack length. The software plots graphs of the crack length increase (Δa) and crack growth resistance (J value) from the acquired data, calculates the JIC value, and evaluates its validity.
-
product
Electronic Loads
Flexible electronic DC loads for general purpose applications. Voltage up to 80V, current up to 80A and power up to 600 watts. CI, CR, CG, CV and CP modes, built-in transient generators. Models with USB, RS232, GPIB and LXI compliant LAN interfaces.
-
product
ISSRs for Mounting on Printed Circuit Boards
Series LS10
Series LS10 DC solid-state relays are designed for mounting on printed circuit boards. They facilitate heat-sinking by providing an interface surface. They can switch loads with high starting currents. The nominal switched currents depend on the size of the heat sink These relays use a direct-bonded copper substrate for thermal efficiency and long life.Available options include:LS60DC10C-21 10A, 7-36 Vdc Load; 3-10 Vdc ControlLS60DC10F-21 10A, 7-36 Vdc Load; 7-30 Vdc Control
-
product
STM32 Arm Cortex MPUs
As Industrial, Consumer, Smart Home, Health and Wellness systems are growing more connected, certain embedded designs are now required to manage high processing loads and complex applications with rich Human Machine Interfaces (HMI). Under these conditions, the ability to harness open-source software stacks while maintaining low power and real-time performance are key requirements.
-
product
Compact Three-Phase Ppower Capacitor
MFB
Lifasa - International Capacitors, SA
These capacitors are especially suitable for the compensation of inductive loads and for the construction of automatic batteries.
-
product
Portable Power Amplifier
PAV120Bip
PAV120Bip（6*120V） is the portable type power amplifier which is specially designed for R&D of power system simulation. It is with linear type amplifier design so that it could be adapted to simulation experiment which may include various capacitive and inductive load.
-
product
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KG
FM-204M50KG
Guangzhou Landtek Instruments Co. Ltd.
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KGApplications:Making job task analysis and ergonomic analysis simple and accurate, it is ideal for workplace design, strength assessment and ergonomic research.Details:Force Rang:±50kgf,±490N,±110LbfResolution:0.01kgf,0.1N,0.1LbfAccuracy:±0.5%FS ± 1DigitUnit:kgf, gf, N, LbfMeasurement State:Peak Value Measurement, Real Time MeasurementDisplay:2 Reversed 4 Digit LCDPower Off:10 Minutes Auto Power Off, Manual Power OffBacklight:Ba...show more -
product
Online UPS
BOXER SERIES 10 - 120 kVA
Equipped with its new IGBT rectifier Boxer series keeps your critical loads protected while its space-saving compact design and front access for maintenance successfully reduce mean time to repair (MTTR).
-
product
Miniature Instantaneous Relays
CU-W Series
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads.
-
-
product
110V / 100 Amp Load
BD12-110P-48/24
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
