Showing results: 2146 - 2160 of 2290 items found.
-
RP4030 -
Teledyne LeCroy
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
ViTec Co. Ltd
The control system is based on the Sick IVC smart camera, which not only captures, but also processes the image. After training on the font samples, the system practically does not require the operator's attention in addition to setting the current marking for control. The character set can be specified by the operator or transmitted via the interface from the printer or from the enterprise information system.The camera software works autonomously: it loads all settings from the camera's permanent memory, initializes the backlight electronics and waits for a signal from the object presence sensor. When a signal is received from the sensor (an object in the shooting area), the camera captures the frame, searches for markings and analyzes the symbols for their compliance with the exemplary set.
-
Pickering Interfaces Ltd.
The SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC. The module is built on a single width 6U PXI module and the interface is via a standard PXI/CompactPCI backplane. Connection to the switching contacts is via three 50-pin D-type male connectors mounted on the front panel. These are machined contact types with 7.5A current carrying capacity.
-
Vishay Intertechnology, Inc.
A passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. High-power resistors that can dissipate many watts of electrical power as heat may be used as part of motor controls, in power distribution systems, or as test loads for generators. Fixed resistors have resistances that only change slightly with temperature, time or operating voltage. Variable resistors can be used to adjust circuit elements (such as a volume control or a lamp dimmer), or as sensing devices for heat, light, humidity, force, or chemical activity.
-
NH Research, Inc.
Enerchron 2.0 test management software is a software suite ideally suited for test applications that yield extensive data over an extended period of time such as battery cycling and evaluation. It allows the creation of complex, dynamic test sequences without requiring the skills of a programmer. In addition to real-time viewing during execution, measurements are automatically archived for review and analysis after testing has been completed. Enerchron is available with NH Research’s Regenerative Battery Test System (Model 9200) or can be used to control additional Battery Test Systems, NHR air-cooled electronic loads, power supplies, temperature chambers, and data acquisition devices that measure temperature and pressure.
-
ForTest Italia Srl
T8730 was designed for the precise task of measuring flows on parts such as filters (medicinal, diesel or petrol), tubes, nozzles, openings, valves, etc…Other than the classic flow measurement, the tool also has other ways of making it as versatile as possible in its category: ascent and descent ramps, opening tests and burst testing.Another separate function is the "continuous measurement", i.e. a test with infinite times allowing adjustment of the taps and part repairs in real time.The tool also avails of an intelligent pressure adjustment, which uses the automatic pressure regulator to continuously adjust the test pressure based on the variation in load loss, to ensure the reading is as stable and repetitive as possible.
-
BCE13 -
D.Marchiori s.r.l.
D.Marchiori (DMA) manufacture double or triple tachometer testers. They use precision controlled DC motors with coaxial optical encoders controlled by a dedicated microprocessor. A quartz timing circuit provides maximum accuracy and control stability. Speed values (% or RPM), rotation direction, transmission ratio and 100% RPM values can be selected separately for each motor. The test set can apply star or triangle resistive load and read the output voltage for generator checks; by entering RPM and test voltage limit values the full generator check can be automatically carried out. The internal printer provides copy of the test results. Safety limits to protect UUT can be set separately for each motor.
-
PSL-3424 Quick Test for 802.at and 802.3bt PSE's -
Sifos Technologies, Inc.
*Accessible from PSA Interactive or PowerShell PSA*Scans 2 to 8 PSE ports per test cycle*Automatically determines and adapts to PSE maximum assigned class*Tests PSE’s that grant full power via PD Classification or through PoE LLDP*Validates PoE Detection Acceptance and Rejection Range*Measures PSE Port Voltage at both minimum (DC MPS) and maximum (Pclass) load conditions*Reports PSE type (AT vs BT), maximum assigned class capability, and Pclass power capacity*Assesses Disconnect Power Removal response*Assesses Overload Power Removal response*Assesses LLDP Power Protocol and Allocations (PSL-3424L)
-
783362-02 -
NI
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
GX5296 -
Terotest Systems Ltd.
The GX5296 offers the most performance and features of any 3U PXI dynamic digital I/O board on the market today. The 32-channel, GX5296 offers timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability emulate and test complex digital busses for system, board or device test applications. Offering 1 ns edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level).
-
LAB-MOBI -
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
P4330 -
P3 International Corp.
Now you can protect your valuable electronics and find out what they are actually costing you. Simply connect these appliances into the Kill A Watt® PS-10, and it will assess how efficient they are while the built-in surge protection keeps them safe. Advanced features such as over current, over voltage, and no load detection provide clean, safe power to your expensive equipment. Check the quality of your power by monitoring Voltage, Line Frequency, Amperage, KWH, Current Leakage and more. Now you’ll know how much power your entire computer or home theater system is using. With the innovative Kill A Watt PS-10 you’ll have peace of mind in more ways than one.
-
SG-PDA -
Jinge Testing Machine Co.,Ltd
It is a state-of-the-art testing equipment to perform high strain pile bearing testing on piles.It will provide prediction on the pile bearing capacity, pile integrity, driving stresses and hammer performance for a given pile penetration. It is a relative low cost type of pile testing compared to static load test (MLT or CRP). The testing technique is quick and accurate.It can also be used to perform high strain pile bearing monitoring to evaluate pile driving information for pile bearing capacity, pile integrity, driving stresses and transferred energy against pile penetration. The results are essential for the actual pile driving process and to obtain valuable data on the hammer, pile & soil system for re-design on the piled foundation (if necessary).
-
PLG Series -
Jinan Testing Equipment IE Corporation
The series of electromagnetic resonance fatigue testing machines are used for fatigue tests of metal materials and components under tension, compression or reversal loads. If relevant grips are provided, three-point bending test, four-point and circle test, gear wheat, bolt, connecting rod, roller chain, crackle expanding test can be available. The series of electromagnetic resonance fatigue testing machines feature an optimized design and a rational structure. The automatic controlled system adopts an advanced and wide-pulse-control system and a new-type of power amplifier to improve the reliability of the electric system. The electromagnetic resonance fatigue testing system is with high efficiency, easy and non-stop shake, low energy consuming, accurate control, and small fluctuation.
-
WEW-D Series -
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard screws), which can satisfy ordinary testing requirements. Digital controller and computer with software can be equipped on this machine to realize the test date/curve collecting and process. The hydraulic UTM of economical type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar etc.
