Showing results: 31 - 45 of 979 items found.
-
Pickering Interfaces Ltd.
Our LXI modular chassis are available in 7 and 18-slot and our LXI/USB modular chassis are available in 2, 4 and 6-slot and support over 1,000 of our PXI modules. The PXI modules supported range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of simulation modules such as programmable resistors, digital I/O, power supplies, thermocouple simulators, function generator, battery simulators and attenuators. This gives you enormous flexibility to define a switching or T&M system to exactly match your needs.
-
Pickering Interfaces Ltd.
2-pole 75x4 matrix modules with one, two or three separate 75x4 matrices housed in the same case (model 60-311) . Capable of cold switching 750VDC continuous with a carry current of 2A plus higher pulse conditions e.g. typically 1000VDC for 1s with low duty cycle or 6A for 200us with <1% Duty Cycle. Front panel Loop-Thru connections allow a 75x4 matrix to be easily expanded to an adjacent matrix in the same case. Also, expansion can be carried out between 60-311 matrices in separate cases.
-
ProDAQ 6140 -
Bustec Ltd.
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
L4400 Series -
Keysight Technologies
The Keysight L4400 Series of switches, digital input/output and analog output instruments offer the best tradeoff in size, functionality and test. They are standalone instruments that perform the same function as their companion 34980A-Series plug-in modules. They come with a fully operational programming interface including a web-page for easy control.
-
60-103B-001 -
Pickering Interfaces Ltd.
This 18-slot LXI Chassis is fully compliant with the LXI Standard 1.4 and allows the large number of our 3U PXI modules to be installed and controlled through a standardized Ethernet interface. Each module is supported as though it is an LXI compliant device, complete with a driverless soft front panel that provides control of the module functions.
-
60-983-002 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-983-003 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-983-001 -
Pickering Interfaces Ltd.
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
60-982-001 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
60-985-050 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
-
60-985-005 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
-
60-985-003 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
-
60-985-030 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
-
60-985-200 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
-
60-985-100 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.