Filter Results By:

Products

Applications

Manufacturers

Instruments

read precision values.

See Also: Instrument Cables, Modular Instruments, Instrumentation Amplifiers


Showing results: 3961 - 3975 of 5005 items found.

  • Insulation / Continuity Tester Proving Unit

    PU250 - Di-Log

    The PU250 allows simple and quick check of insulation resistance and continuity for all makes of I/R testers.Regular checks outside of the formal calibration process are required for compliance with BS7671 and Part P.Proving unit to enable compliance to the requirement to maintain records of regular checks on the measurement characteristics and accuracy of test instruments.

  • Water Quality Products

    Cole-Parmer Instrument

    When you need to perform critical water testing, look to us for an extensive selection of electrochemical meters, controllers, probes, electrodes, test kits, buffers, and standards. Our field and laboratory instrumentation include water analysis instruments for dissolved oxygen, temperature, pH, conductivity, salinity, and turbidity.

  • PXI Source Measure Unit

    NI

    PXI Source Measure Units (SMUs) combine high-precision source and measure capability with features designed to reduce test time and increase flexibility. These features include high channel density for building parallel SMU test systems, deterministic hardware sequencing for minimizing software overhead, and high-speed update and sample rates for quickly changing setpoints and acquiring data. Additionally, the flexible sampling rate and streaming capability of PXI SMUs allows you to use the instrument as a digitizer to capture transient behavior, and the digital control loop gives you the ability to adjust the transient response of the instrument. The ability to change the transient behavior of the SMU, called SourceAdapt, reduces SMU settling time and minimizes overshoot and oscillations, even with highly capacitive loads.

  • DC Parametric Test System with Curve Trace

    DC3 - Hilevel Technology, Inc.

    The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.

  • Flying Prober Test

    QTOUCH1202C - Qmax Test Technologies Pvt. Ltd.

    he Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.The V-I signature test shall be in-built in the Prober system with “ Best fit Curve “ algorithm .Provision for adding various external Test & Measurement instruments like GPIB / USB / PXI Instruments is available.

  • Concrete Strength Testers

    Qualitest International Inc.

    This category of products comprises the range of instruments utilized to evaluate construction material strength. The range of instruments is typically considered to be two parts. The first are non-destructive field tests of compressive strength. The second are tensile field tester systems to either determine the tensile strength of an overlay or bond material, or tensile strength of anchors embedded in the concrete. The first group is pure Non-Destructive Testing where the strength of the material is determined by correlation to another parameter more easily available and readily apparent. This is typically the hardness of the concrete or the resistance to penetration by either a pin or probe. The Windsor Probe, Windsor Pin and our line of Rebound Hammers all fall within this category. These are widely used standard tests and as such have seen use throughout the world.

  • Ethernet, GPIB And USB To Serial Interface Board

    ICS Electronics

    ICS's Model 9006 is a multi-interface to serial board that adds Ethernet, GPIB and USB interfaces to serial devices or older instruments. Use with an embedded processor board to create smart instruments with multiple interfaces. The 9006's Ethernet port is VXI-11 compatible for easy control by the following computer systems without special drivers: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. VXI-11 is one of the 9006's Ethernet protocols. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.

  • GAOTek Three-Channel Leakage Current Tester

    GT00YB00ZV - GAO Tek Inc.

    The GAOTek Three-Channel Leakage Current Tester provides online measurement, monitoring, and recording of three channel AC leakage currents simultaneously by adopting the latest CT and magnetic shielding technology. This instrument provides highly accurate and reliable measurements. Additionally, it can locate insulation faults and repair electrical lines. It is composed of a special alloy and consists of a test monitoring software, current clamp, and communication cable. The instrument can store 3900 sets of data and enables online and real time monitoring, historical data inquiry, read, inquire storage, generation, and printing of a fitting curve. It is widely used in 380/220 power systems. It complies with IEC1010-1, IEC1010-2-032, Pollution Class 2, CAT Ⅲ (600 V), and IEC61326 (EMC standard) safety codes.

  • Chemiluminescence 03 Analyzer

    Model T265 - Teledyne Advanced Pollution Instrumentation

    The Model T265 is the only commercially available US EPA Federal Reference Method for Ambient Ozone Monitoring according to the latest US EPA regulatory rules for O3. The instrument uses Chemilumescence with Nitric Oxide (NO) as a reagent, making is safe, stable, and effective for all applications. The NO-CL method for Ozone has several advantages over the conventional UV absorption technology, including the avoidance of positive and commonly found interferrents such as VOCs, fine particulates, Mercury, turpines, ClO2, and others. If these pollutants are present in the atmosphere, it can cause UV absorption analyzers to give an artificially high Ozone measurement. The innovative T265 combines speed of response, sensitivity and stability of our proven nitrogen oxide analyzer, with a simple user interface, to provide reliable ozone measurements under the harshest conditions.

  • Coupling Decoupling Network for Communication Lines

    CDN61000-5C - Lisun Electronics Inc.

    • Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments

  • Ethernet to GPIB Controller

    Model 8065 - ICS Electronics

    * Controls GPIB Devices anywhere there is a network or internet connection.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* VXI-11 compliant.* Includes ICS's VXI-11 and VISA keyboard control programs.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver lets you change network settings from any browser.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the GPIB instruments.* 8065 is our original Ethernet to GPIB Controller and recommended for replacement purposes with existing programs. Use the Model 9065 for new applications.

  • General Purpose Geiger Counter

    Radalert® 100X - International Medcom

    The Radalert® 100X is a general purpose geiger counter that measures alpha, beta, gamma, and X-radiation. Features of the Radalert® 100X, include a three-second update and a Utility Menu that allows you to change the default settings for several operating parameters. Its digital liquid crystal display (LCD) shows the current radiation level in your choice of SI units (microsieverts per hour) from .000 to 1,100 and counts per minute (CPM) from 0 to 350,000 or counts per second (CPS) from 0 to 3,500. For users of conventional units mR/hr (milliroentgens per hour) from .000 to 110 and CPM are optional in the Utility Menu. This instrument also offers an accumulated total and timer function, up to 9,999,000 counts and 40 hours.

  • Halogen Moisture Analyzer

    HC103 - Mettler-Toledo, LLC

    The HC103 measures moisture content in minutes, enabling fast response times for quality control and in-process control. A large color touchscreen, graphical user guidance and real-time drying curve make the HC103 easy to use, even for untrained operators. Whether you work in a busy laboratory or a harsh production environment, the compact design saves space and the robust construction guarantees a long instrument lifetime. With touchscreen operation and an intuitive user interface, the HC103 is easy to use. Operators can access drying methods directly from the home screen with just ''One Click''. As the measurement is running, a real-time drying curve is displayed on the screen to provide an overview of the progress. Operators can clearly see if the moisture content is on target and are able to intervene quickly in the production process where necessary.

  • Modular SEC system

    SC2000 - Postnova Analytics GmbH

    The new Postnova SC2000 Modular SEC system offers unrivalled flexibility in Advanced SEC/GPC analysis. It is the first truly modular multi-detector SEC system available allowing flexible access to a wide range of applications. The system incorporates state-of-the-art detection technologies including light scattering (MALS > multi-angle light scattering) for absolute molecular weight and Viscosity detection for structural and conformational data. Many other detector and accessory options and combinations are available to build a system uniquely tailored to your application requirements, with the benefit of modularity to allow easy future expansion. In addition, the SC2000 can be further expanded to include FFF modules to widen the application range and allow both SEC and FFF separations to be carried out on the same sample within one instrument platform.

  • Motor Unit

    Adamant Namiki Precision Jewel Co Ltd.

    Today, so many units products such as medical equipment, automobiles, fuel cells, robots, and precision instruments. These performances are supported by the performance of motors, on the other hand, mechanical design, parts processing, and control The maximize the performance of the motor, which is an engine, are indispensable . The functions required for unit products are very diverse, including precision drive , high output, light weight, low heat generation, low vibration, and low power consumption.Actuation technologies such as optimum motors, speed reducer, non-energized locking mechanism "dyNALOX", compact clutch mechanism, torque transmission mechanism, control, and our core technology "cutting" "sharpening" "polishing" precision We combine process parts and precision assembly technology and we propose the optimum solution with a unique idea unique to our company, which is a motor manufacturer.

Get Help