Filter Results By:





read precision values.

See Also: Instrument Cables, Instrumentation Amplifiers

Showing recent results 3736 - 3750 of 4238 products found.

  • Analog & Mixed Signal Tester - AMIDA 3000 Series

    AMIDA-3001XP - Amida Technology, Inc.

    AMIDA recently introduced two new analog / mixed signal and logic options for AMIDA – 3000 series – the AMIDA – 3001 XP and AMIDA – 3050 test systems. Both enhance the ability of the AMIDA-3000 Series to provide cost- optimized test solutions for the full range of power consumer and mobility devices. AMIDA – 3000 Series offers double the analog and digital pin count per instrument as current analog subsystems, resulting in lower cost per pin and twice the pin count per system. This enables higher levels of multi-site for cost – effective testing across a board range of applications. It provides a powerful combination of hardware and software features targeted at the test requirements of high speed IOs. The real time protocol detect feature built into the AMIDA – 3000 Series simplifies test development and can be used to reduce test time of high speed IOs by up to 60% ~ 100%.

  • Laser Distance Meter

    KM 973 - KUSAM-MECO

    • Measuring Range : 0.05 to 40M (KM 973) , 0.05 to 70M (KM 975), 0.05 to 100M (KM 976) • Measuring Accuracy : ± 2 mm• Display Accuracy : 1 mm• Laser Classification : Class 2M II• Laser Type : 620-690nm, <1mW• Protection against splashes and dust : IP 54• Temperature range for Operation : 0°C to +40°C• Temperature range for Storage : -20°C to +70°C• Laser Switch-OFF Automatically : After 30 Seconds• Instrument Switch-OFF Automatically : After 3 Minutes• Area, Volume Measuring.• Indirect (Pythagoras) Measurement.• Plus-Minus Method.• Continuous Measurement.• Minimum / Maximum Measurement.• Display illumination.• Show beep.• Battery Life : 5000 to 8000 Measurements• Battery Selection : Lr6 (AA) 2 x 1.5V• Dimensions : 121(L) x 56(W) x 28(H) mm• Weight : 150g

  • Luminance Colorimeter

    XYL-VI - Lisun Electronics Inc.

    The XYL-VI Luminance Photoelectric Colorimeter changes the traditional structure thoroughly, employs the digital X(λ), Y(λ), Z(λ) sensors to replace the traditional analogue sensors, employs the digital signal measurement system to replace the traditional analogue measurement system. The instrument has no analogue unit, thus it is very simple to overcome the zero drift that is impossible to be avoided in traditional colorimeter. The digital sensor has a large dynamic range. Moreover, it possesses strong anti-interference ability and it has high accuracy. The XYL-VI Luminance Colorimeter contains internal RS232 computer interface. The calibration is done by software. It is suitable for monitoring and remote applications. The XYL-VI Luminance Colorimeter can be calibrated by XYL-VI Luminance Colorimeter software to sample the data and print out the results. It can also be corrected by other standard light sources to obtain very high measuring accuracy of x, y color coordinates and color temperature. It is a real-time measuring system and run under Windows2000/XP.

  • Modular SMU Series

    Keysight Technologies

    The wide range of available models and advanced measurement features provides a variety of price-performance points for parametric measurement and analysis. Modular product family members enable customization now and provide for future expansion as requirements change, while 2-channel units provide cost-effective solutions for simple test needs. The E5270B is targeted at precision semiconductor device characterization, and the E5260 Series (E5260A, E5262A, and E5263A) is targeted at high-speed production test. For all members of this product family, a number of innovative design elements -- such as expanded program memory -- help to improve the efficiency of complex testing. Cost-of-test is also lowered through superior measurement throughput, often several times faster than earlier instruments (such as the 4142B). The new 4.0 version of Keysight Desktop EasyEXPERT software can control the product family by using sample application tests on Desktop EasyEXPERT. The product family also gives you the option of using your own software.

  • pH & ORP Sensors

    Barben Analytical

    The Barben Analytical Performance Series products are 3rd generation combination pH/ORP electrodes targeted at harsh, industrial measurement applications. High pressures, strong chemicals, and elevated temperatures typically shorten the lifespan of conventional double-junction pH probes. In these applications the Performance Series sensor offers extended sensor lifespan, as well as decreased drift, and longer calibration intervals. Each sensor is manufactured with our patented Axial Ion Path® reference technology, proprietary Low-Noise & High-Temp Signal Cable along with proprietary ruggedized, high temp and coat resistant glass formulations. A wide selection of sensor body styles and process fittings in a variety of corrosion resistant materials allow direct replacement of short-lived OEM pH/ORP sensors. Barben Performance Series sensors are compatible with all major manufacturers of pH analyzers and transmitters. Upgrade your analytical measurement without the hassle and expense of replacing costly field instruments.

  • Static Locator Micro Kit

    PCS-715 - Prostat Corporation

    The PCS-715 Micro Kit features the PCS-715A Static locator that indicates electrostatic field voltage up to 20,000 volts, as well a polarity of static charged surfaces. The kit includes a fine grain leather case with Prostat's "quick release' belt clip system.The PCS-715A Static Locator is a non-contact meter that indicates electrostatic field voltage and polarity on charged surfaces. This easy to use instrument comes equipped with a Power On/Hold button and a zero button. The meter automatically shuts off after approximately 90 seconds. The unit's grounding path is through its conductive case, so there is often no need to wear a grounded wrist strap during normal operations. The easy to read 3-1/2 digit LCD display automatically updates three times per second. Measurements are dependent on the distance from the object being measured. The unique one inch spacer makes distancing easy and repeatable.

  • Ultrafine Particle Monitor

    Model 651 - Teledyne Advanced Pollution Instrumentation

    Ultrafine particle (those less than 100nm, or 0.1µm in size) are produced through combustion activities and are persistent in all ambient air. Concentrations of these tiny particle can be very high near emissions sources (for example, near busy roads), and both acute and chronic exposure are believed to lead to health problems. As part of the new US EPA near-road ambient monitoring network, ultrafine particles (UFPs) will be monitored to determine concentration levels and further study health effects related to exposure.The Model 651 Ultrafine Particle Monitor provides a simple and reliable solution for the real time monitoring of UFP concentrations in ambient air. The instrument uses a condensation particle counting technique, using water as the condensing fluid followed by laser detection. UFPs down to 7nm in size are detected, with time resolution down to 1-second. Sample collection, preparation, and analysis occur continuously, with a routine maintenance interval of 30 days.

  • ESU Analyzer

    ESU-2050 - BC Group International Inc.

    The BC Biomedical ESU-2050 ESU Analyzer is the first instrument of its kind on the market. Designed through extensive collaboration with several of the world's leading electrosurgery generator manufacturers. It is the only ESU Analyzer on today's market with a 1% reading level of accuracy. Calibration quality analyzer; uses external precision non-inductive test loads and wide band current transformer.

  • Nail Test Probe

    CX-Z12 - Shenzhen Chuangxin Instruments Co., Ltd.

    The Finger Nail Probe is indicated to test IEC 60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the necessary force for using the instrument. This probe is made of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.

  • Test Finger Nail Probe

    CX-75 - Shenzhen Chuangxin Instruments Co., Ltd.

    The Finger Nail Probe is indicated test IEC60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the neccessary force for using the instrument. This probe is make of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.

  • Field Communicator

    HR-HART475 - HighReach Measuring & Controlling System Co.,Ltd

    This communicator is suitable for HART protocol smart transmitter communication operation, compatible with HART275HART375, has excellent compatibility, and communicate with instruments of 1151, 3051, EJA, ABBE+H Fuji and other HART protocols, fully compatible with domestically produced An intelligent pressure transmitter Can format the original 1151. It can be various various HART flow meters, temperature meters, etc.

  • Multi-Wavelength Optical Light Source

    Shanghai Baudcom Communication Device Co.,Ltd.

    BD-POW-D02N Optical laser light source is a self-developed instrument, Which features advanced control technology , high output, ultra low-power operation. It can work at single wavelength, dual wavelength or three wavelength. It can export a variety of modulation frequency (CW, 270HZ, 1KHZ, 2KHZ). It is widely used in optical communication, optical measurement, optical fiber sensing, and so on.

  • Torque Speed Meter

    VTS-01 - Veer Electronics

    VEER make Torque Speed Meter VTS-01 is portable instrument which is very useful to find Output Power, Torque in Kgm, RPM, Corrected RPM, %Slip and Frequency of Motor. It is very simple and easy to use. It measures torque of motor from load cell & RPM from Proximity Sensor which are very useful to find output power of Motor.

  • Automated DC Parametric Curve Tracer

    MegaTrace - Robson Technologies, Inc.

    MegaTrace supports pin counts greater than 625 up to 2160 pins, with 1080 pins being popular. Comprised of a cart that contains the test chassis, PC monitor, drive bus box, and a test interface, MegaTrace is easy to move around and use with other instruments like emission microscopes, probe stations, and other remote testing requirements.

  • Relay

    PXI-2565 / 777754-01 - NI

    16-Channel, 7 A, SPST PXI Relay Module—The PXI‑2565 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It delivers high-current switching of DC power supplies, AC line power, and AC/DC current sources. The PXI‑2565 is fully software programmable and supports multiple instrument synchronization.