Showing results: 3616 - 3630 of 4979 items found.
-
TM510 -
T&M Tools Limited Co
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
-
NEBULA -
Intellitech Corp.
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital multimeter TH1941 4 1/2-digit is voltage/ current /resistance tester with multi functions and low cost. The instrument can stably perform measurement at high speed as several times as other instruments at the same level. It provides excellent performance, such as maximum reading of 12,000 counts, maximum DC voltage accuracy of 0.02%, and low cost to give you a best choice. Having VFD dual-display with high brightness. TH1941can synchronously display measurement parameters, such as AC/DC voltage or current, AC voltage/current and frequency to improve measurement efficiency and display results clearly.
-
TideM8 -
Ohmex Instruments
The TideM8 is a black box instrument designed around the same 'winstrument' specification as used in the popular SonarMite portable echo sounder, this design criteria specifies that all display and interactive communications with the instrument use Bluetooth radio technology to communicate with a PC or PDA device. Through extensive experience of tide gauge installation and manufacture the TideM8 design is modular with separate radios, gauge, display and power supply units. This modular design enables the user to configure every combination from a simple gauge and PDA to a gauge and remote display using radio telemetry communications.
-
KT-200SG -
Kast Eng Co. LTD.
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
M9122A -
Keysight Technologies
The M9122A is an 8x32 full crosspoint switch matrix offering high-voltage switching in a high-density PXI module. This module allows for higher voltage switching of multiple channels in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This module is configured with a common ground. The durable armature switches are capable of switching up to 100Vrms, with up to 60W of power. The 8-wide bus can be used to route signals between your instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
Megger Group Ltd.
Megger Baker Instruments designs and manufactures electric motor test systems for original equipment manufacturers (OEMs) that help ensure their motors, generators and coils meet or exceed the quality expectations OEMs set with their customers. Baker motor quality control (QC) systems include the Baker WinAST automated stator tester, the Baker HV WinAST and the Baker WinTATS traction armature test system. Each incorporates the most effective electric motor test processes into a single automated instrument and can be customized to meet the specific testing needs of a given manufacturer.
-
GEA 3 -
PASI srl
Gea3 is a 24-bit real data acquisition seismograph in a waterproof container.This small, extremely lightweight instrument is equipped with 3 channels+one displayable trigger channel and is the perfect solution for a variety of applications: *DOWN-HOLE seismic measurements with the use of a 3D well geophone (such as PASI Mod.GFA or Mod.DHTG)*CROSS-HOLE seismic measurements combined with a 3D well geophone (such as PASI Mod.GFA or Mod.DHTG) and a P/S hole energizersmall-scale seismic refraction with surface geophones and 3-channel seismic cable*MASW and Vs30 profiles with a special triaxial geophone (like PASI Mod.3DLG - 2Hz)
-
FAXE -
Elmika
Fixed Attenuators are waveguide components for introduction of some particular attenuation value in to the waveguide network for signal leveling or reflection compensation. The attenuators have two types of design: with resistive plate in the waveguide diagonal plane or using coupling technology. The FAXE 3, 6, 10, 15, 20, 30 dB attenuators are available in waveguide bands from 18 through 225 GHz. The FAXE Fixed Attenuators can be used as laboratory Standards against which other instruments or devices are calibrated in case the parameters of these Fixed Attenuators are stable enough and were measured with appropriate accuracy.
-
DLF 2800 -
TA Instruments
The Discovery Laser Flash DLF 2800 is an advanced freestanding instrument for the measurement of thermal diffusivity and specific heat capacity of materials from room temperature to 2800°C. The distinctive design incorporates a proprietary laser, laser optics, detector, and furnace technologies, and along with the unique six-position sample carousel, ensures unprecedented measurement accuracy and sample throughput. With the ability to operate in a variety of atmospheric conditions, including inert gas or under vacuum, the DLF 2800 can characterize a wide variety of materials, including polymers, ceramics, carbons, graphite, composites, glasses, metals, and alloys.
-
IMADA, Incorporated
Imada mechanical force gauges are highly accurate instruments used to test the quality, strength or functionality of component parts or products. Imada mechanical force gauges check both compression and tension (push or pull). Peak force can be captured using the peak indicator needle and the tare ring compensates for the weight of attachments. Imada force gauges are constructed with a heavy-duty metal case and all metal components to enable them to retain their calibration for years with proper care. These mechanical force gauges never need charging or batteries and are intrinsically safe in hazardous environments.
-
MCA3000 -
Tektronix, Inc.
Offering up to 40 GHz measurements, the Tektronix MCA3000 Microwave Analyzer Series packs many different functions into one feature-rich instrument. The integrated power meter and two additional timer/counter channels offer you even more test functionality than other microwave analyzers on the market. With unprecedented resolution, you can capture very small frequency and time changes. And with the industry's most comprehensive analysis modes, including measurement statistics, histograms, and trend plots, you have the tools you need to quickly and accurately analyze your signal.
-
4865B -
ICS Electronics
* Embed the GPIB-to-Ethernet Interface in your instrument.* Available in three different connector configurations.* To have the GPIB Connector protruding thru the rear panel. Order P/N 115907* To mount the board anywhere inside the chassis and use an inexpensive flat-ribbon cable to a GPIB connector on the rear panel. Order P/N 115895. Order the 114439 Cable separately.* Mount inside the chassis and use a GPIB extension cable to a GPIB connector on the rear panel. Order P/N 115897.* Runs on instrument's DC power.* Same specifications and performance as the 4865B Minibox™ version.
-
4ABAC -
Elcontrol Energy Net S.r.l.
The high technological content, the great attention to the choice of materials, full compliance with industry regulations, make this instrument a reference (the “North Star”) to orient themselves with efficiency and simplicity in the control of electricity consumption and the main parameters power quality.Polar Star was conceived, designed, built and tested entirely in Italy, and therefore manufactured with quality assurance that distinguishes European products, in the real environment and ethics.His communication skills allow its use in Elcontrol monitoring networks of any size and geographical location. Two available versions 8Base and Top) allow to fit best any application requirement.
-
E1 & T1, Data, DSL, Protocols, BER Analyzers -
GAO Tek Inc.
With 20 years of experience in the development and production of test instruments, GAOTek is proud to provide a large selection of PSTN analyzers that meet the requirements of technicians working in the telecom industry for sale to the United States, Canada and Globally. Public Switched Telephone Network (PSTN) was designed to ease the two-way communication between two points or two users. In the beginning, a direct connection between two points was very simple, however the cost was too high depending on the distance and geography. The network engineers revolutionized voice communications by creating PSTN which is still in use today.
