-
product
PXI Dual Microwave SPDT Relay 50GHz 50 SMA-2.4
40-780A-552
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
Rubidium Generator
SRO-100
Rubidium generators SRO-100 are designed to generate and output to the consumer highly stable, high-frequency, spectrally pure sinusoidal signals with a frequency of 5 or 10 or 15 MHz.
-
product
Noise Figure And Gain Test Extenders
SA full noise figure and gain test extender that extends the noise and gain measurement capabilities of common and low frequency signal synthesizers and noise figure meters to the frequency range of 110 to 170 GHz. This extender is designed to interface with industry standard noise and gain test systems.
-
product
Power Inverters
A power inverter, inverter or invertor is a power electronic device or circuitry that changes direct current to alternating current. The resulting AC frequency obtained depends on the particular device employed.
-
product
Cable Assembly, Type-N (m) to Type-N (m), DC to 18 GHz
11500D
The Keysight 11500D is a 152 cm (60 in) type-N male to type-N male cable assembly with a frequency range of dc to 18 GHz.
-
product
2-Port Optical Tunable Filter
Optoplex's Tunable Optical Filter, also known as Optical Tunable Filter or Tunable Bandpass Filter, is an integrated module, consisting of micro optics and electronics. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), the 2-port tunable optical filter directs a selected channel to the Output-Port (OUT). The selected channel can be varied (tuned) within the operating wavelength (frequency) range by a remote command sent through the built-in control PCB and firmware.
-
product
RF Amplifier Modules
Analog Devices RF amplifier modules offer high linearity, low noise figures, and low phase noise, as well as low power consumption. These devices are all fully specified over frequency and temperature for use in a variety of applications.
-
product
Comb Generator
CG118
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
product
PXIe-6614, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module
782353-01
PXIe, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module—The PXIe‑6614 is a high-precision counter/timer module that performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS‑compatible digital I/O. The PXIe‑6614 offers industrially rugged features for a wide array of applications such as automotive/ae...show more -
product
Limiter
Chengdu KeyLink Microwave Technology Co., Ltd.
The series of products‘ limiting ability can be achieved by the diode conduction and cut-off characteristics.The frequency range covered by 0.5GHz~40GHz.The products have the characteristics of low insertion loss, small size and high reliability. The products can be applied to receiving channel low noise amplifier protection in radar system. KeyLink's limiters can be categorized as follows.
-
product
Microphone Calibration Workstation
9350C
The Precision Acoustic Calibration Workstation Model 9350C is an accurate, turnkey, automated PC-based system that features cost-effective calibration of ¼", ½" and 1" microphone cartridges (open-circuit sensitivity), microphone cartridges with preamplifiers (closed-circuit sensitivity) and microphone Frequency Response Function.
-
product
Function Generators
Waveform : Sine, Triangle, Square, Pulse, Sawtooth, Ramp 0.2Hz-150MHz EXT Frequency Counter(Option : 1:6 GHz or 2.7GHz) Self made insert ASIC Function : Total, RPM, Period, LPF, COUPL(AC/DC), ATT(X10) Fast,High-Resolution, 8Digits LED display Internal or External AM,FM Modulation Internal or External Burst and Linear Sweep Countrol from 1 : 1 to 100:1 TTL/CMOS Leveled Square Wave Output Maximum Attenuation of 20 dB cna be obtained Output impedance : 50 INPUT SENSITMTYKHz Range : 100mVms, MHz Range : 300mVms SWEEP WIDTH : Variable from 1:1 -100:1 RATE : 0.5Hz - 50Hz(20ms-2s) INTERNAL : Linear Bilt-in 5digits Green LED display
-
product
Receivers
Macom Technology Solutions Holdings Inc.
MACOM's receivers are widely used in point-to-point radio, aerospace and defense, and other broadband communications applications. Operating between the 4.5 - 45 GHz frequency range, our receivers feature an integrated LNA, mixer and LO buffer amplifier onto a single chip. Available in lead-free QFN or SMD packages, our receivers boast excellent noise figure and conversion gain performance.
-
product
SensiSUB
Delivering Sensor Reading Overcome any Obstacles. Better Range and Reliable Frequency Band Penetrate walls and Reduce collisions.
-
product
Single Frequency Lasers: 355 nm – 1064 nm up to 3 W
Cobolt 05-01 Series
High power, single frequency CW diode pumped lasers: 355 nm – 1064 nm up to 3 W. Perfect for holography, interferometry, Raman, optical tweezers, super resolution microscopy, laser doppler velocimetry
-
product
Planar-Doped Barrier Diode Detector, 100 kHz to 2 GHz
8471D
The Keysight 8471D is a low-cost, planar-doped barrier detector offering excellent performance to 2 GHz. A negative polarity output is standard, and a positive polarity is available as Option 103. A load option (Option 102) extends the square-law region to at least -10 dBm. The Keysight 8471D has a BNC (m) input connector and a frequency range of 100 kHz to 2 GHz, making it ideal for use in RF and low microwave applications.
-
product
Field meters
Small, lightweight and low priced non frequency selective Efield meter. It can be used for relatively high field strengths e.g. to observe the field in a TEM cell or a strip line.
-
product
FM Tokenless Transmitter & Receiver
MS 1522
Transmitter and Receiver units are designed to work at 24V DC voltage (nominal) with variation between 19.2 V to 28.8V. The system is designed to work with carrier frequency 1800/2700 Hz and modulated frequency 65Hz/85Hz. For 1800Hz Carrier Frequency RED border is used in Front Panel and for 2700Hz Carrier Frequency BLUE border is used in Front Panel. Maximum power consumed by transmitter and receiver are 1.2W and 8W, respectively. Sense level for receiver is less than –19 dBm and No sense level...show more -
product
Absorbing Clamps
The Absorbing Clamp was designed to measure the disturbance power according to CISPR 16-2-2 in the frequency range 30-1000 MHz, it complies to the technical requirements of CISPR 16-1-3.
-
product
Generators
Signal Generator
Signal Generator is used for forming signals of various shapes, amplitude, and frequency at the output channels of ADC and DAC modules and FFT spectrum analyzers. Functionally, the Signal Generator software replaces stationary generators used in laboratories.
-
product
Linear Accelerometer Switch
Columbia Research Laboratories
Columbia Research Labs Accelerometer Switch is designed to interface with electrical or mechanical systems to control, safeguard against, or warn of undesirable variations in DC and low frequency acceleration. This sensor is available with a selectable switch point, a single or Bi-polar switch, and a choice of input power.
-
product
USB-6351, 16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
781440-01
16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6351 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6351 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Low-Mid Frequency Analyzer
LMFA-21
Amfax introduce the latest PXI based High Performance Low and Mid Frequency Analysis System operating from 100Hz TO 2MHz with an extremely low noise floor. This high accuracy measurement instrument utilizes the National Instruments Function Generator and Flex Digitizer to optimize your frequency related product performance. Using the industry standard PXI platform enables us to offer the system a fraction of the cost of other typical two box solutions.
-
product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 4 Prescaler
HMMC-3024
The HMMC-3024 is a DC - 12 GHz divide by four pre scaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
Waveguide Harmonic Mixers (smart mixer), 75 to 110 GHz
M1970W
The Keysight M1970W 75 to 110 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of N9030A PXA, N9020A MXA,and N9010A EXAsignal analyzers up to 110 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
product
Broadband Amplifier
BBA150
The R&S®BBA150 broadband amplifier family generates power in the frequency range from 4 kHz to 6 GHz. The compact amplifiers are rugged and feature high availability.
-
product
Audio Oscillator & Sweep Generator
SweepGen
SweepGen turns a PC into an Audio Oscillator and Sweep Generator which can be used for testing audio or educational purposes. In conjunction with audio test instruments, you can make frequency response plots. SweepGen uses the sound card in your PC to produce sine waves that are mathematically correct almost to CD quality, indeed it's more likely that the quality of your PC sound card will be the limiting factor rather than the code in SweepGen.
-
product
Automated Test Interface
ATI-100
Matrix Test Equipment Incorporated
Now, with our ?New? Model ATI-100 you can turn your existing Matrix Signal Generator and Switchable Filter Bank into a full-blown DTS (Distortion Test System). Plug and play is the word, just plug in your Multiple Frequency Signal Generator, Switchable Filter Bank, Spectrum Analyzer, Oscilloscope, Power Meter, Frequency Counter, etc. to allow the following automatic testing with a single insertion of DUT (device under test
-
product
Ferrite Devices
Ducommun's products include very broad ferrite device selections to cover 100 MHz to 110 GHz operation frequency range. These devices include narrow band drop-in (FID and FCD), connectorized (FIC and FCC), junction (FIW and FCW) isolators and circulators and iso-adapters (FII and FCI). The broad bandwidth versions are offered as full band junction isolators and circulators (FIF and FCF) and Faraday isolators (FFF). These devices feature low insertion loss, high isolation and wide operating temperature range. Low cost and volume production versions of these ferrite devices are available per customers’ request.
-
product
Portable Calibration Shaker Table
AT-2030
The AT-2030 portable calibration shaker table is designed for simple accelerometer and vibration transducer calibration without the need for advanced features. AT-2030 shaker table and vibration calibrator is a variable frequency, variable amplitude, battery operated portable shaker capable of calibrating accelerometers, transducers, and proximity probes. Applications are producing a known vibration signal in g’s, mils, or ips for sensor, wiring, instrumentation, and system checkout in vibration condition monitoring applications.