Showing results: 646 - 660 of 706 items found.
-
rBOX510-6COM (ATEX/C1D2) -
Axiomtek Co., Ltd.
The rBOX510-6COM(ATEX/C1D2) robust din-rail fanless embedded system is certified with ATEX and C1D2 for use in hazardous environments where ignitable concentrations of flammable gases, vapors or liquids might exist. The embedded system supports the dual-core Intel® Atom™ processor E3827 1.75GHz SoC with the onboard 4GB DDR3L system memory. The din-rail heavy-duty embedded PC adopts an IP30-rated aluminum and steel enclosure, and can perform in wide temperatures ranging from -40°C to +70°C. To prevent ESD and over-voltage, the compact embedded box PC is equipped with four isolated RS-232/422/485 ports, two isolated 10/100/1000Mbps Ethernet ports, and one isolated DIO (8-IN/8-OUT) port. One 2.5" SATA SSD, one mSATA and one CompactFlash™ socket are available for storage. More I/O features include one USB 3.0 port, one USB 2.0 port, two COM ports, and one VGA output. In addition, box PC comes equipped with a wide range 12 - 48VDC power input with a terminal block and has overvoltage and reverse protection. The box PC provides two watchdog timers and RTC battery function. Pre-installed with Linux, Windows® 8 Embedded and Windows® 7 Embedded, the embedded system provides programmers with a friendly environment for developing application software at a lower cost. For secure mounting, the rBOX510-6COM(ATEX/C1D2) can be easily installed on a DIN-rail mount or in an enclosure box.
-
Cuming-Lehman Chambers
Cuming-Lehman Chambers MIL-STD 461E/F test chamber is specially designed for testing in accordance with the military standard.MIL-STD 461 SHIELDING SYSTEMOur MIL-STD 461F/DO-160 enclosure is modular panel construction; the panels are a laminate of 26 gauge, electrolytically deposited zinc sheet steel laminated to both surfaces of ¾” thick solid, (structural) core material. These panels have a flame spread of 20 minutes or less as rated by Underwriters Laboratories, Inc. The panels are joined by specifically designed framing members that clamp the edges of the panels and provide constant, low impedance joints with the shielding elements of the chamber. Weld nuts are on 3” centers and our corners are welded; no screws are used and nothing penetrates our chamber.
-
RAD242 -
Acces I/O Products, Inc.
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
Carl E. Holmes Company
- Active Switching Power Supply Using MOSFET, 125 KW, P/N 5940C2- Input: 480 VAC, 150 Amps, 3 PH, 60 Hz- Output: 0 to 50 VDC, 2500 Amps max- Ten modules in parallel, each module is rated for 0 to 50 VDC, 300 Amps- PLC Control provides Positive Polarity, Negative Polarity and Shuts OFF- Start / Stop capability and EPO- Output voltage and current are displayed on the voltmeter and ammeter- PLC supplied by the customer. We provide a PLC interface only- Indoor enclosure dimensions: 65″W x 50″H x 36″D or (TBD)- Estimated weight: 2000 lbs. or (TBD)
-
Rapidox 2100-OEM-RSB-WALL -
Cambridge Sensotec Ltd
The Rapidox 2100 OEM-RSB-WALL is a wall mount version of our miniaturised 24V OEM oxygen (O2) analyser. The compact (4.5″ x 3.0″) circuit is integrated into a neat IP65 wall mount polycarbonate box, with a clear smoked hinged lid. Behind this is a clear OLED display and menu keypad. The box is completely electrically isolated and meets all UL and IEC standards for these types of enclosures. There are cable entry glands on the base for power cables and analogue / digital / alarm leads The analyser comes with a robust cabled zirconia sensor, which is ideal for providing fast and accurate remote in-situ gas analysis over the the full oxygen range 10-20ppm to 30% O2. An optional external pressure sensor socket is included as standard.
-
Type NVF-2 -
National RF, Inc
The Type NVF-2 series of handheld directional antennas are used to locate interfering signals or noise in either the 420 – 470 MHz (Type NVF-2A) or the 900 MHz ISM band or cellular telephone bands (Type NVF-2B). Both models incorporate a solid reflector positioned behind a resonated half wave driven element, both elements being mounted on a fiberglass rod with an integral pistol grip. The configuration of the reflector and driven element are such that a deep null in the signal being received will occur when the antenna is pointed in the direction of the signal being radiated. A T-pad resistive attenuator is also incorporated in the antenna mounting enclosure to aid in the direction finding process on very strong signals or when excessive reflections present multiple returns.
-
PCE Instruments
Originally designed for the medical sector, endoscopes are the ideal tool for inspection and maintenance today. Endoscopes offer new perspectives to viewing the insides of machines. Thanks to their flexible fibre optic cables and light weight enclosure, these extraordinary endoscopes are the ideal tool for inspection and maintenance. Endoscopes can locate problems and conflicts of the system very easily and quickly, allowing for preventative measures to be taken without the need to dismantle the machinery first. Complex dismantling of machines is usually very time and cost intensive. With the help of endoscopes, inspections in an industrial sector can therefore be organized considerably faster, more aimed and more cost-efficiently Endoscopes are used mainly by electricians, security personnel, specialists in the professional sector, and mechanics of all types. All of our endoscopes are ***Not for medical use***
-
PI-2500 -
ETI Precision
The PI-2500 is a versatile and technologically advanced primary injection tester capable of testing circuit breakers up to 2000 amperes frame size. It incorporates a low-impedance output transformer with dual secondaries to provide optimal impedance matching to a wide range of breaker sizes. High-capacity internal fan cooling allows maximum utilization of the output transformer and faster recovery after overload conditions. It is housed in a rugged aluminum frame enclosure with removable sides allowing easy access to all internal components to facilitate ease of service and maintenance. The output of the test set is controlled by means of a proven SCR controller. This provides precise initial phase angle control to reduce DC offset for inductive loads and more consistent pulse currents.
-
Sciencetech, Inc.
The Solar Reference Cell consist of a 20 x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 x 70 x 16 mm metal enclosure with a protective quartz window and a temperature sensor. The temperature sensor is a 100 ohm platinum Resistance Temperature Detector (RTD).The Solar Reference Cells come with a Certificate of Calibration and compatible set of connecting cables. The following parameters of the reference cell are certified: Isc, Imax, Voc, Vmax, Pmax, Area, Fill Factor and Efficiency. The certification is accredited by NIST to the ISO-17025 standard and is traceable both to the National Renewable Energy Laboratory (NREL), and to the International System of Units (SI). A compatible cable set is also supplied with each Solar Reference Cell.
-
DM330 -
AMETEK Drexelbrook
The Drexelbrook DM330 magnetostrictive level transmitter is a two wire loop powered intrinsically safe sensor with a configurable 4 -20 mA span.This level transmitter uses proven machine tool positioning accuracy combined with a process compatible float to offer a liquid level, and interface measurement system for the process industry.It comes in a patented low clearance design with all of the sensor’s electronics integrated in a 5/8” diameter sensing tube eliminating the electronics enclosure at the top of the sensor. Not only does this result in reduced cost it also offers its user greater options for insertion and mounting.The DM330 is available in two models.The rigid 316SS model offers a choice of a mini-connector or an optional housing including terminal connectors with zero and span adjustments.
-
16814 -
Ultra-Tech Enterprises, Inc.,
The MU Locomotive Trainline/Cable Test System (MU Test System) can perform shorts testing, continuity testing, and ground-leakage testing on each of the 27 pin Multi-Unit Trainlines normally found on Freight Locomotives. The MU Test System is comprised of two identical tester units. Each unit is installed in a rugged, water resistant Pelican case. Each unit contains an MU cable receptacle that mates with a 27 pin MU jumper cable. A snap-on vinyl pouch on the outside cover of each unit provides storage for the battery charger/power adapter and the chassis test lead. The enclosure cover hinges separate from the test unit as the cover is opened; this removes the cover completely to allow free access to the MU cable receptacle and the control panel.
-
Model 6353 -
Pentek, Inc.
- Small form factor rugged enclosure- Conduction-cooled- Designed to the IP67 specification for dust and water immersion- Sealed military-grade circular connectors- Incorporates Xilinx® Zynq® UltraScale+" RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- Optional dual 100 GigE UDP optical interface- Optional fan cooling for benchtop use- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
FAB100 -
Axiomtek Co., Ltd.
The FAB100 features one CPU card slot, four ISA slots, four PCI-E x1 slots, one PCI-E x16 slot, and four 32bit/33MHz PCI slots. This PICMG 1.3 backplane also supports a built-in 24-pin ATX power connector. Furthermore, the FAB100 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491 and AX6145, to house the FAB100 and any customer's industrial integrations flexibly.
-
NanoSync IV & NanoSync IV Low Profile -
FEI-Zyfer Inc.
The NanoSync IV is a small form factor GPS Position, Navigation, Time (PNT) and Frequency reference system that provides multiple reference outputs and includes support for NTP & PTPv2 IEEE 1588-2008. The NanoSync IV has a Rubidium oscillator and is available with a civilian C/A GPS receiver or SAASM (Rockwell-Collins MPE-S GB-GRAM or Trimble Force 22E MRU GPS receiver) for military users. The NanoSync IV is packaged in a small, rugged enclosure ideally suited for embedded electronic warfare applications.The NanoSync IV-SA-Rb has been demonstrated to be compliant to the Joint Airborne SIGINT Architecture (JASA) Version 3.0, Annex 1, for Time, Frequency, Navigation and Geodesy (TFNG), making it suitable for Electronic Warfare (EW) COMINT and ELINT applications in fixed site, airborne and shipboard environments.
-
Model UDA -
tecsis LP
Model UDA is a universal signal conditioner and amplifier designed for use with all full bridge, strain gage-based transducers. Model UDA turns the analog signal into a user-selectable output of ±5Vdc, ±10Vdc, or 4-20mA. This versatile unit features selectable excitation of 2.5 or 5.0Vdc bridge voltage and has a wide DC power input range from 11 to 28Vdc to adapt to a variety of installations. Model UDA includes a wide zero and span adjustment range and a symmetry adjustment for applications requiring precision in both tension and compression. The configurable low pass filter actively removes unwanted high frequency signal components. The unit is housed in a rugged DIN-mountable enclosure with screw terminals to provide connection for power, analog output, shunt calibration, and sensor signals.
