Showing recent results 316 - 330 of 349 products found.
-
Techimp HQ S.r.L
TEM antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset (like MV switchgears or LV and MV induction motors fed by power electronic impulses). It is a broadband antenna with a flat response which makes TEM suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes TEM the optimal sensor for direct installation on medium voltage Switchgears and motors. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces.
-
Guangzhou Jumho Electric Co., Ltd.
Cell phones and other wireless devices radiate powerful electromagnetic fields that can cause interference and noise in microphone signals. The interference and noise is called RF interference, which is an unwanted “signal” that occurs at the same time and frequency as a data signal. The RF interference disrupts the flow of data and degrades quality-of-service. Jumho Electric provides a cost-effective RF interference test system for GSM interference level measurement of wireless microphone.
-
Acces I/O Products, Inc.
Sensors that are used to collect the data from the environment often don’t produce signal of characteristics optimal for an analog to digital converter (ADC) to translate to digital data. Additionally, these signals can be subject to electromagnetic interference (EMI) that introduces noise, having a negative impact on the reliability of the data. To make this analog input readable for the processing unit and dependable enough to give the desired quality of data the signal has to undergo a process of signal conditioning.
-
Ultra Precision Technologies Division of Ametek
Power Systems and Instruments offers control room annunciators and displays, specialized utility communications equipment, power monitoring and metering instruments, uninterruptible power supply systems, programmable power equipment, electromagnetic compatibility test equipment, industrial battery chargers, power conditioning equipment for medical and life sciences devices, and sensors for gas turbine generators. It serves the electric power generation, utility, transmission and distribution industries worldwide.
-
Hybrid - Hilo Test
Surge pulses occur due to direct or indirect lightning strikes in a circuit or by switching transients caused by switching inductive loads or short circuits. This leads to currents or electromagnetic fields causing high voltage or current transients. Surge voltages and currents can reach several thousands of volts and thousands of amperes. Our following Surge generators simulate these disturbances for all the necessary level in accordance with IEC / EN 61000-4-5 and IEC / EN 60060.
-
ZPS - Zygo Corporation
The ZPS™ system provides high-precision non-contact absolute position measurement on up to 64 synchronized channels. ZYGO's new ZPS™ system measures absolute position using ultra-compact optical sensors that are easily integrated into high-precision applications such as deformable mirrors and lens positioning. The optical sensor system provides up to 64 synchronized channels of high-precision, non-contact, absolute position measurement over a range of 1.2 mm. Measurement resolution is 0.01 nm with ≤ 1 nm/day measurement stability.The optical sensors do not generate heat and are insensitive to electromagnetic interference, making the ZPS system ideal for high-precision applications that may be affected by these factors. The ultra-compact sensors connect to the compact centralized enclosure via fiber optic cables.
-
EM Explorer
EM Explorer is a 3D electromagnetic (EM) solver for scattering problems of periodic structures illuminated by arbitrary incident fields including planewaves, Gaussian beams and focused Hi-NA beams. It can simulate both complex dielectric and complex magnetic materials including left-handed materials (LHM) that have a negative refractive index. EM Explorer is largely based on the same method of Finite Difference Time Domain (FDTD). Therefore it inherits most of FDTD's advantages and disadvantages. The advantages include simple & robust numerical algorithm, versatility for nearly any geometries, and good scalability of computing resources as a function of simulation volume size. The disadvantages are numerical dispersion and stability constraint due to the finite difference (FD) approximation to Maxwell's equations and explicit time marching algorithm.
-
L-Band - QuestTel
QuestTel''s Satellite L-Band optical fiber Transmitter/Receiver set offers high pefromance and cost effective alternative to conventional coaxial systems. The L-Band Transmitter and Receiver pair is used for transporting L-Band RF over fiber from the antenna to the satellite receiver. Additionally transmitter provides optional 13/18V LNB power as well as Automatic Gain Control (AGC) to manage RF input level. By transporting the L-Band RF over fiber this range can be extended from several hundred feet to over 80 miles. Since optical signal is not affected by electromagnetic field, the quality of your signal will always stay at the high level. Also this fiber solution is more cost effective than coaxial system, as well as more reliable and flexible.
-
SNAPTrack® - Rycom Instruments, Inc.
Built on a proven design, and with Pathfinder SAF Technology™ at its core, the SnapTRACK® offers RYCOM’s most advanced signal acquisition and filtering technology. The SnapTRACK® cable & pipe locator offers utility locators FrequencyFlex™ allowing users to adapt the system to their specific needs. Multiple active frequencies allow the user to accurately locate with a minimum of interference while maintaining the ability continue locating past faults and around conduit bends. Passive frequencies identify "live" and charged lines by their naturally occurring electromagnetic fields. The SnapTRACK® offers multiple passive frequencies -- 50Hz, 60Hz, Radio Frequency, Cathodic Protection Rectifier & CATV -- allowing line locating without the use of a transmitter.
-
W2372EP - Keysight Technologies
The RF Architect, Synthesis, Modulated RF Element provides the industry's most powerful communication system architecture, frequency planning and circuit/system synthesis capabilities from Genesysto the Advanced Design System (ADS), the flagship product from Keysight EEsof EDA.Analyzes RF systems withdigitally modulated RF signals. It offers breakthrough budget analysis of EVM, BER, and ACPR on level diagrams which determine their contribution from each system component stage. You can then verify the system against LTE-3GPP and WLAN 802.11ac wireless standards. ADS is the only design simulation platform that enables the co-design of IC, package and board in high-frequency and hi-speed applications. It seamlessly integrates system, circuit, full 3D electromagnetic simulation with Keysight's test instrumentation for you to do single pass successful electronic designs.
-
W2401BP - Keysight Technologies
The W2401BP Electromagnetic Professional (EMPro) Core Environment provides a modern 3D solid modeling environment for creating arbitrary 3D objects and importing existing models from other CAD environments. From EMPro, both time domain and frequency domain simulations can be launched and results viewed. EMPro is integrated with Keysight's Advanced Design System (ADS) circuit design flow through import of ADS layout objects, and export of parameterized 3D components that can be added to an ADS layout.
-
KH23101 - Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
MKS Instruments
MKS offers compact industrial microwave generators and systems in 915MHz and 2450MHz that are adaptable to a wide range of applications including include Food and Beverage Packaging, Environmental and Advanced Industrial processes like coating, material growth, and automotive. With a robust, modular power system chassis design and advanced filament and electromagnetic management, MKS microwave generators are engineered to last. The microwave generators are equipped with switch mode topology for all power ranges and support a variety of fieldbus communication protocols.
-
W2324EP - Keysight Technologies
The High Capacity Layout Pre-processor Element is an ODB++ file format import and pre-processing tool that enables you select the environment immediately around critical nets in preparation for electromagnetic (EM) modeling. This type of pre-processing is useful in high-speed digital design where the printed circuit board (PCB) is very complex and whose total geometry exceeds the capacity of an EM-based field solver. The solution is to focus in on a handful of critical nets; for example, a differential pair connecting two Serializer/Deserializer (SERDES) integrated circuits (ICs) that is a victim of crosstalk from one or more aggressor traces. An example of such a trace is shown highlighted below in Figure 1. Note that the board has been "cookie cut" meaning a convex hull with a user-defined margin has been defined, leaving a portion of the board whose complexity is within the capacity constraints of full-accuracy, full-wave EM field solvers such as Momentum and FEM Element.
-
RF2 set - Langer EMV-Technik GmbH
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
