Filter Results By:

Products

Applications

Manufacturers

Showing product results. 241 - 255 of 412 products found.

  • Radio Equipment Directive

    National Technical Systems

    The RED is the legal document instructing the European Union member states on the regulatory framework for placing radio equipment on the market in the EU. As with other EU directives, it describes “essential requirements” for radio equipment. These essential requirements of RED are to ensure protection of health and safety, adequate electromagnetic compatibility (EMC) and effective and efficient use of the radio spectrum. Directives are not standards.

  • RF Safety Monitoring

    MVG EME Guard XS 40GHz - LBA Group, Inc

    EME Guard XS 40 GHz has been specifically designed to cover the new 5G millimeter wave bands. This RF safety tool is important for keeping those working close to RF emitters safer. It is easy to use, continuously scanning electromagnetic waves, and alerts the user when acceptable pre-selected limits have been exceeded.

  • Stack Probing Sensor

    L722 - Wagner Electronics

    The Model L722 Stack Probing Sensor coupled with the L612 Digital Recording Moisture Meter makes it easy to reach deep into stickered units of lumber and take accurate moisture readings without the danger of broken pins. Wagner''s electromagnetic wave technology makes it possible to take multiple readings throughout an entire stack in just minutes.

  • Near-Field Probes 100 kHz up to 50 MHz

    LF1 set - Langer EMV-Technik GmbH

    The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.

  • Momentum G2 Element

    W2341EP - Keysight Technologies

    The Momentum G2 Element is the improved 2nd generation of the powerful Momentum 3D planar electromagnetic simulator from Keysight EEs of EDA, the technology and innovation leader in high-frequency mixed-signal electronic design automation (EDA). Momemtum G2 is seamlessly integrated into the Advanced Design System (ADS), the only design simulation platform that enables the co-design of IC, package and board in high-frequency and hi-speed applications. It seamlessly integrates system, circuit, full 3D electromagnetic simulation with Keysight's test instrumentation for you to do single pass successful electronic designs repeatedly.

  • 4051 Series Signal/Spectrum Analyzer (3Hz to max. 67GHz)

    4051 - Saluki Technology Inc.

    4051 series signal / spectrum analyzer has good expansion capacity, and can improve the features by means of flexible configuration options and also can construct testing system or redevelop by means of the output interface of all digital and analogue signals. The analyzer is applicable for signal and equipment test of fields including aviation, aerospace, radar detection, communications, electromagnetic countermeasure, and navigation.

  • Automation

    50 Hz Adaptive Filter - ZETLAB Company

    One of the main causes of the reduction of accuracy in low frequency signal parameters measurements is the influence of artificial and natural electromagnetic interferences on measuring channels of measuring tools (MT). Under laboratory, production and natural conditions, the main interference is 50 Hz network interference. To eliminate this interference, ZETLAB software package uses a program providing a 50 Hz band-stop filter.

  • Cable Harness EM Solver

    MHARNESS - Electro Magnetic Applications, Inc.

    MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.

  • EMPro Core + FDTD + Compliance Bundle

    W2403BP - Keysight Technologies

    The W2403BP Bundle enables you to draw arbitrary 3D objects, import existing 3D CAD objects and run Finite Difference Time Domain (FDTD) simulations, all from the Electromagnetic Professional (EMPro) 3D EM Platform. You can also perform regulatory compliance testing for applications such as hearing aid compatibility (HAC) and specific absorption ratio (SAR).

  • GTEM Cells / TEM Cells

    Teseq AG

    The GTEM cell is a frequency extended variant of the traditional TEM (Transverse Electro-Magnetic) cell. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a combination of discrete resistors and RF absorbers to achieve a broadband match. Designed for EMC applications, calibration of antennas/field probes, test and measuring of mobile phones and screening measuring of material.

  • Keysight EEsof Electronic Design Automation (EDA) Software

    Keysight Technologies

    Keysight EDA is the leading supplier of electronic design automation software for communications product design. RF and Microwave circuit, high-speed, signal integrity, device modeling, power electronics, and signal-processing design engineers accelerate the development of better products using design flows built on our device modeling, electro-thermal, electromagnetic, circuit and system design and simulation tools.

  • Measurement Power Amplifier

    Qam - QSources BVBA

    The amplifier is DSP controlled, with a very straightforward operation. Included is a white/pink noise signal generator. The internal signal module provides low crest noise signals to be able to reach high power levels from sound sources or electromagnetic shaker. External input of signal is equally possible, with spectral linearisation or without. This can be used for music, RASTI or any other signal

  • PDSurveillant

    PD-RD300A - PowerPD Inc.,

    The PD-RD300A is the newest device in the PowerPD line of test equipment, which provides continuous monitoring of your metal clad switchgear (MCSG) assets. This device detects electromagnetic waves when surface tracking occurs on the insulation system. It determines the PD fault frequencies by scanning the 10 -100 MHz range. Data is collected in bursts (Envelop) by the count method.?

  • Spiral Antenna

    Techimp HQ S.r.L

    UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.

  • The Electrosmog Detector

    MW1 - Sensory Perspective Ltd

    This new ?broadband? detector exposes and converts the electromagnetic impulses it encounters into a collection of sounds (buzzing, screeching, pulsing) that is far more varied and illuminating than the ?click? of a geiger counter. You can hear the amount, type, amplitude, and quality of the pulsed electronic pollution created by local transmitters/emitters operating between 50MHz and 3000 MHz, and enjoy the silence when the environment is clear.

Get Help