Filter Results By:

Products

Applications

Manufacturers

Showing product results. 226 - 240 of 409 products found.

  • Radiation Resistant Resolver

    Computer Conversions Corporation

    Computer Conversions GT Transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bidirectional, and electronically passive devices (no electronic components to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.

  • LISN

    EMCTEST

    The LISN (Line Impedance Stabilization Network) or AMNs (Artificial Mains Networks) is a device to create a known impedance on power lines of electrical equipment during electromagnetic interference testing. Frequency range: 150kHz a 30MHz

  • Near-Field Probes 100 kHz up to 50 MHz

    LF1 set - Langer EMV-Technik GmbH

    The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.

  • GTEM Cells / TEM Cells

    Teseq AG

    The GTEM cell is a frequency extended variant of the traditional TEM (Transverse Electro-Magnetic) cell. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a combination of discrete resistors and RF absorbers to achieve a broadband match. Designed for EMC applications, calibration of antennas/field probes, test and measuring of mobile phones and screening measuring of material.

  • Keysight EEsof Electronic Design Automation (EDA) Software

    Keysight Technologies

    Keysight EDA is the leading supplier of electronic design automation software for communications product design. RF and Microwave circuit, high-speed, signal integrity, device modeling, power electronics, and signal-processing design engineers accelerate the development of better products using design flows built on our device modeling, electro-thermal, electromagnetic, circuit and system design and simulation tools.

  • Measurement Power Amplifier

    Qam - QSources BVBA

    The amplifier is DSP controlled, with a very straightforward operation. Included is a white/pink noise signal generator. The internal signal module provides low crest noise signals to be able to reach high power levels from sound sources or electromagnetic shaker. External input of signal is equally possible, with spectral linearisation or without. This can be used for music, RASTI or any other signal

  • Spiral Antenna

    Techimp HQ S.r.L

    UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.

  • Thermal Vacuum Data Acquisition and Control Software

    TVAC 7000 - WinSoft Inc.

    Equipment used in space applications needs to go through stringent environmental tests in order to prove that it can survive the extreme conditions experienced during launch and while in space. Some of the key environmental tests include vibration, thermal vacuum, and electromagnetic compatibility.   Thermal vacuum test is crucial to confirm the equipment is able to operate under the space vacuum condition.​

  • Waveguide Twists

    Precision Milimeter Wave

    Waveguide twists and bent types of waveguides are used extensively in electromagnetic devices. Twist waveguides are used to change the polarity of the fields. Waveguide twist VSWR is as low. Both 45° and 90° waveguide twists are available. The 45° versions being available in both right hand and left hand twist configurations.View more Twist Waveguides

  • Automation

    50 Hz Adaptive Filter - ZETLAB Company

    One of the main causes of the reduction of accuracy in low frequency signal parameters measurements is the influence of artificial and natural electromagnetic interferences on measuring channels of measuring tools (MT). Under laboratory, production and natural conditions, the main interference is 50 Hz network interference. To eliminate this interference, ZETLAB software package uses a program providing a 50 Hz band-stop filter.

  • Cable Harness EM Solver

    MHARNESS - Electro Magnetic Applications, Inc.

    MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.

  • EMPro Core + FDTD + Compliance Bundle

    W2403BP - Keysight Technologies

    The W2403BP Bundle enables you to draw arbitrary 3D objects, import existing 3D CAD objects and run Finite Difference Time Domain (FDTD) simulations, all from the Electromagnetic Professional (EMPro) 3D EM Platform. You can also perform regulatory compliance testing for applications such as hearing aid compatibility (HAC) and specific absorption ratio (SAR).

  • Energy Efficiency Testing & Certification

    Eurofins E&E

    In addition to testing equipment for product safety, environmental simulation, and electromagnetic compatibility, MET is a leader in Energy Efficiency Testing. Please choose an energy efficiency testing category: ENERGY STAR Testing & Certification for U.S. Environmental Protection Agency Efficiency Certification for Natural Resources Canada California Energy Commission Appliance Efficiency Program Energy-Efficiency Requirements for Europe

  • EMF Detector

    ElectroSensor™ - Sonic Technology Inc.

    This EMF detector is an unparalleled value that offers fast, reliable, and user-friendly measurements of electromagnetic pollution. Since man-made alternating current (AC) is different from naturally occurring EMF, some sources say that even extended exposure of as low as 2 milliGauss may be harmful. Fortunately, once EMF sources are identified with your ElectroSensor you can moderate your distance and exposure.

  • Inductive Sensors

    Bee Instruments

    Inductive Proximity Switches, self contained, depend on the output of an oscillator for their operation. The oscillator resonant circuit uses an open core coil to produce a concentrated high frequency electromagnetic (RF) field, which emerges from the active surface of the sensor. If a metal target (or other electrically conductive material) enters this field, eddy currents will be induced in it, causing the resonating oscillator to be damped.

Get Help