Showing results: 1861 - 1875 of 2551 items found.
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Techimp HQ S.r.L
TEM antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset (like MV switchgears or LV and MV induction motors fed by power electronic impulses). It is a broadband antenna with a flat response which makes TEM suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes TEM the optimal sensor for direct installation on medium voltage Switchgears and motors. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces.
-
KT3202 -
Ketai instrument (kunshan) Ltd.
It has AC and DC voltage, DC current, resistance, capacitance, continuity, and diode measurement functions.Comply with safety standard CAT III 600V Fuse Φ6x31mm 600VKT3202 is a specially designed AC and DC voltmeter.KT32034 specially designed AC and DC ammeter.KT3204 is a specially designed DC low-current, low-voltage meter. The voltage can be measured from 0 to 100mV, and the current can be measured from 0 to 50uA.The pointer "0" is at the median value, and the voltage and current are divided into two sides.This set of four tables has certain practical significance for students' knowledge and understanding of Ohm's law in electrical engineering.This set of meters complies with the CAT III 600V standard.
-
KT3204 -
Ketai instrument (kunshan) Ltd.
It has AC and DC voltage, DC current, resistance, capacitance, continuity, and diode measurement functions.Comply with safety standard CAT III 600V Fuse Φ6x31mm 600VKT3202 is a specially designed AC and DC voltmeter.KT32034 specially designed AC and DC ammeter.KT3204 is a specially designed DC low-current, low-voltage meter. The voltage can be measured from 0 to 100mV, and the current can be measured from 0 to 50uA.The pointer "0" is at the median value, and the voltage and current are divided into two sides.This set of four tables has certain practical significance for students' knowledge and understanding of Ohm's law in electrical engineering.This set of meters complies with the CAT III 600V standard.
-
Ajinkya Electronic Systems
Real Time Switch is a real time timer which can be used to switch electrical appliances like street lamps, garden lights, corridor lights, neon signs etc as per time of the day. The timer has built in almanac timings fixed in nonvolatile ram so that the user does not have to programme the unit from time to time. This has added advantage over daily dial or weekly timers. Timer provides two outputs to drive contractors of different ratings. These outputs can be used with different combinations to achieve desired output. Timer is provided with manual override facility. Optional detachable external keyboard unit provided to avoid unauthorized access.
-
Ironwood Electronics
*Package-size PCB footprint: Since the PCB footprint of G80 is identical to the package, only one PCB design is required, enabling a seamless transition from test and validation through production and reducing overall cost of test*Low insertion force: Unique contact design reduces the insertion force required to insert and retain higher-ball-count packages safely and securely within the test socket*No lid required: The package snaps directly without a lid, enabling easy probing, scoping and troubleshooting the topside of the device*Excellent signal performance: A short signal path achieves low inductance and low insertion loss, providing a nearly invisible electrical connection
-
ODP3032 -
KILTER ELECTRONIC CO.,LTD
3.9 inch high resolution ( 480 x 320 pixels) TFT large LCD display,can clear visual display state and a plurality of relevant parametersTwo separate controllable output 0V ～ 30V / 3A,A fixed output 5V / 3A, total output of high power 195WThree channel output and electrical isolation,greatly reduce circuit interference Low ripple and noise of pure power:（<300 uVrms / 2 mVpp）Output resolution :1mV/1mAInternal implementation independent, parallel, series , positive-negative four kinds of work modes and automatic trackingOvercurrent and overvoltage protection function,Can easily set up the overvoltage and overcurrent protection parameters,effectively protect the load
-
Pontis EMC
Most of our cameras can operated remotely. The controllers allow to control the functions of the cameras:– Zoom– Focus– Audio– Pant/Tilt– optionally iris– LANThe controllers convert the optical signal to electrical signalsFor most controllers there is the option to integrate an Ethernet interfaceMost of the controllers can be equipped with an option for shielded intercom. The microphone is either integrated in the housing or a separate microphone can be used.If more than one camera is in use (e.g. one fixed and one mobile camera) multi controllers allow to control several cameras with one device.Up to 4 cameras can be connected to one multi controller. Each camera can be connected to a separate monitor each one monitor can show the selected camera.
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Universal Impact Hammer is designed to perform impact tests for product durability. The CX-T03 meets the testing needs of industry standards such as IEC 60065, 60335, 60598, 60601, 61010 and others. The hammer simulates mechanical impact to electronic products and electrical appliances. This impact hammer is versatile -- it can be dialed to a whole range of energy values to perform tests to many different standards. A compressed spring accelerates a hammer head to hit the sample undergoing test. The spring is released from a lock mechanism by pressing the cone-shaped top of the impact hammer against the product under test. The CX-T03 is adjustable from 0.2 Nm to 1 Nm by turning a ring on the hammer.
-
Osborne Transformer Corp.
The Institute of Electrical and Electronic Engineers defines a current transformer (IEEE Std C57.13) as “a transformer intended to reproduce in its secondary circuit, in a definite and known proportion, the current of its primary circuit with the phase relations substantially preserved”. Its primary winding is connected in series with the conductor carrying the current to be measured or to be controlled and its secondary winding is connected to the measuring, protection or control devices. Osborne designs and manufactures current transformers which are used for instrumentation applications, others which are used for power system synchronizing applications and others which are used in protection circuit application. They have been designed to meet specified current ratios, burden impedance and transformation errors.
-
Rapidox 1100Z-OEM-RSB & 1100ZR3-OEM-RSB -
Cambridge Sensotec Ltd
The new Rapidox 1100Z-OEM-RSB is the World’s first miniature zirconia oxygen analyser with pump designed to be DIN rail mounted into customer’s equipment as a true OEM. The Rapidox 1100-OEM-RSB is a cost-effective 24Vdc OEM version of our sampling 1100 zirconia analyser range. The package has been shrunk down and simplified to fit onto a DIN rail in an electrical cabinet, and comprises a compact control unit (with or without OLED display and menu keypad), a zirconia sensor with sample connection points, a particle filter and a powerful miniature sample pump capable of drawing a gas sample at up to 1.5 litres per minute through 6mm OD/4mm ID flexible tubing.
-
EPM 2200 -
GE Digital Energy
The EPM 2200 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. EPM 2200 can easily be mounted in a panel for generator monitoring, substation automation and more. The meter can also provide data to RTUs, PLCs and other control devices.
-
6420 -
Peaceful Thriving Enterprise Co Ltd
This is a device to test the 12 volt lead-acid battery of any vehicle. The tester will focus on health condition analysis of vehicle battery; it will estimate the cold cranking ampere (CCA) of the vehicle, and predict the lifetime of the battery. This will be helpful for the technician to inspect and maintain the electrical system of the vehicle. Base on the inspection, user can predict the time to replace the battery.
-
Extech DV23 -
Extech Instruments Corporation
Use DV23 to quickly check for the presence of live wires before performing any electrical testing. Suitable for outlets or against wire insulation testing, this AC Voltage Detector for non-contact detection of AC Voltage from 50 to 600V (50/60Hz). Red LED indicates the presence of voltage. Comes with two AAA batteries.
-
MD257 -
Matco Tools
*Provides readings for volts, amps and ohms required for automotive electrical system tests as well as diode and continuity tests*Lo-Z ghost voltage buster drains ghost voltages leaving only hard signals on meter readings*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
