Showing results: 1711 - 1725 of 2546 items found.
-
Fortress Technology Inc.
The Phantom Pharmaceutical metal detector provides the ideal solution for detection and rejection of the smallest contaminants in tablets and capsules. With its current GMP design and construction suited for FDA compliance, the system meets the stringent QA requirements of the pharmaceutical industry. A free IQ/OQ Validation package is included. Built with a rugged mirrored stainless steel exterior, contact parts are all removable for cleaning without the need for tools. This compact detector can be easily angled and height-adjusted to suit any press configuration. Plus, it’s the only detector that features an electrical powered lift.
-
HTD-4000 -
Qualitest International Inc.
HTD 4000 is used to measure case depth and is capable of verifying case depths ranging from 0.4mm (16 thou) up to a maximum of 2.5 / 2.8mm (100110 thou). Our system utilizes a new and very advanced principle based on the continuous measurement of the electrical resistance in relation to the working load applied. Our design meets the demands of the heat treatment industry. HTD 4000 is equipped with a big stand to enable the testing of large work pieces having overall dimensions up to 550mm (22") in height and 350mm (13.8") depth
-
WIPL-D d.o.o.
WIPL-D kernel is unique in many ways, allowing the most efficient full wave EM simulations. It is based on the Method of Moments (MoM) but applied to quadrilateral mesh elements. In addition, the basis functions are HOBFs (Higher Order Basis Functions) which means up to 2 lambdas large mesh elements. The electrical size of problems is expressed in number of unknowns, rather than in mesh elements. The quad mesh offers two times less unknowns than the traditional triangular one, while using HOBFs reduces number of unknowns several times.
-
40-830-103 -
Pickering Interfaces Ltd.
The 40-830 is a 75 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-830 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
SCR ELEKTRONIKS
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
GWT A2 -
SCR ELEKTRONIKS
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
42-832A-001 -
Pickering Interfaces Ltd.
The 40-832A-001 (PXI) and 42-832A-001 are 75 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-832A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
40-872A-101 -
Pickering Interfaces Ltd.
The 40-872A-101 (PXI) and 42-872A-101 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
40-872A-001 -
Pickering Interfaces Ltd.
The 40-872A-001 (PXI) and 42-872A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
42-832A-101 -
Pickering Interfaces Ltd.
The 40-832A-101 (PXI) and 42-832A-101 are 75 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-832A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
42-832A-002 -
Pickering Interfaces Ltd.
The 40-832A-002 (PXI) and 42-832A-002 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-832A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
42-834A-002 -
Pickering Interfaces Ltd.
The 40-834A-002 (PXI) and 42-834A-002 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-834A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
40-834A-102 -
Pickering Interfaces Ltd.
The 40-834A-102 (PXI) and 42-834A-102 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-834A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
42-834A-102 -
Pickering Interfaces Ltd.
The 40-834A-102 (PXI) and 42-834A-102 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-834A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
F-Squared Laboratories
F2 Labs can provide you with Federal Communications Commission (FCC) Certification in our EMC Testing Lab, Supplier’s Declaration of Conformity (SDoC), formerly Verification and Declaration of Conformity, testing. Manufacturers who sell electrical and/or digital products in the United States must have their products tested by an accredited lab certified by the FCC. F2 Labs is accredited by the FCC as a Conformity Assessment Body (CAB). We partner with a Telecommunication Certification Body (TCB) in order to provide our clients with FCC Part 15 certification and compliance testing & approvals.
