-
product
Surge Voltage Generator
SSG 500
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 500. The SSG 500 surge voltage generator is arranged in a 19'' housing. Maximum safety is achieved with the electrical safety control unit, the automatic discharge unit, the fully enclosed design and separate protection and system earth.* 6 output voltages up to max. 16 kV available* Electromagnetically actuated surge switch* Preselectable surge energy: 288 / 512 Ws (in all voltage ranges)* Automatic discharge unit
-
product
Lightning Surge Generator
CDN-5810
Shanghai Sanki Electronic Industries Co., Ltd.
CDN-5810 signal line/data line coupling decoupling network, unshielded symmetrical communication line suitable for surge pulses and ringing wave pulses, designed according to Figure 10 of the new standard IEC61000-4-5.Ed3. It also satisfies ringing Figure 10 requirements of wave standard IEC61000-4-12.Ed2. According to the characteristics of the line, the pulse coupling can be realized by gas discharge tube, capacitor, diode and other different methods.
-
product
Intelligent Battery Charger Know Capacity,Alkaline Batteries
SE-1004B+
●For AA, AAA size Alkaline ,Ni-MH ,Lithium batteries●Three mode: Charge , Discharge & Internal Resistance●Capacity Range: 4Ah●Prevent over heat while charging●Auto alarm at the end of charge or discharge ●Display charge voltage, capacity(Ah) , Intenal Resistance(mΩ) ●Used for mobile phone or camera battery ●Accessories: battery clamp, power adapter
-
product
Basic Fuel Pressure Tester Kit
FIT450
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose.
-
product
Fuel Pressure Tester Kit
FIT500
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose and protective rubber boot.
-
product
PMS Leak Test System
The system (Pressure Measuring System) is a portable, complete system for leak tests. This consist of the pressure test kit PMS3000 for performing leak tests with an integrated graphic-capable 4.3” color touch display and a pressure relief kit DAK2000 for discharge test according to W400-2, Part 16 pressure loss methods as well as DIN EN 805. The system is complemented by a variety of connection accessories like the rugged accessory case (individually equipped), the test standpipe PSR and accessories for building gas connection as well as the electronically controlled test pumps EPP and the compact air compressor KLK1030.
-
product
Battery on-line Monitoring Tester
HD Power Test Equipment Co.ltd
Battery on-line monitoring system tester is a on-line battery monitoring and auto maintain system for USP,EPS, DC power supply, communication power supply . The tester has the function of monitoring and alerting for a series of parameters such as battery pack voltage, battery pack current, cell battery voltage, cell battery internal resistance, battery environment temperature, Cell Battery negative temperature and battery voltage balance, residual capacity and discharge. It can automatically maintain balance voltage, which used for on-line monitoring 2V and 12V battery.
-
product
Charge Plate Monitor
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the char...show more -
product
Battery Charge and Discharge Tester
HTCFD / 790
Wuhan Huatian Electric Power Automation Co., Ltd.
The voltage monitoring information of single battery is simple, safe and accurate with wireless relay access.
-
product
Electrostatic Discharge Generator
STT-ESD-2005
Beijing KeHuan Century EMC Technology Co,.LTD
Is a tester that meets the requirements of IEC61000-4-2 and GB/T17626.2. Its maximum electrostatic discharge voltage can reach 30kV, covering the electrostatic voltage requirements in the standard (the electrostatic voltage requirement for the fourth level of air gap discharge is 15kV), and it is suitable for more application fields and the requirements of future new standards. Therefore, the ESD-2005 electrostatic discharge generator can be used for most electrical and electronic equipment electrostatic discharge tests, and can ensure the comparability and reproducibility of the test.
-
product
Electrostatic Discharge Simulator
ESD61000-2
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD61000-2/ESD61000-2A has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
product
Telecomunication & Electrical Insolation- Continuity-Voltage-MOV Tester(LCD Display)
1165IN
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) , AC and DC voltage● Six insulation test voltages (DCV): 50V, 100V, 125V, 250V, 500V, 1000V● 68x34 mm (2.677x1.338 inch) large LCD● Function rotary switch design for easier operation● Intuitive operation for users● User friendly interface● Auto ACV/DCV detection● Audible voltage warning● DAR/PI indication● Backlight function● Automatic circuit discharge● Test insulation at rated voltage into a 1mA load● Auto ranging● Fuse protection● EnerSave function● MOV test function
-
product
Digital (1kV below) Insulation Tester
1161 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm (2.677” × 1.338” ) large LCD display.● Waterproof design, protection class : IP54.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● Auto ranging.● Fuse protection.● Data hold function● BS 16 edition.
-
product
PD-Free High Voltage Testing Transformer
YDQW
Wuhan Sangao Electrical Test Installations Limit Co.
Gas-filled HV Testing Transformer is a high-end testing transformer which firstly marketed in China by our company. The high-light characteristic of the equipment reflects the smallness in size, lighter in weight clean, oil-free, unnecessary static of field investigation, longer working life without maintenance and slightness in non-partial-discharge. It is used for the insulators' voltage-resistance testing.
-
product
Insulation Tester (For Telecoms)
1801 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Solid state circuitry.● Battery check feature.● Automatic circuit discharge.● Three insulation test voltages.● Color-coded scale.● AC voltage measurement.● Fuse protected.
-
product
WizardOne Battery Charger-Analyzer for 4 AA / AAA
MH-C9000
It's like having four charger-analyzers for AA and AAA NiMH / NiCD batteries. Refresh & Analyze: Charges the battery, rest for one hour, discharge, rest again, then recharges it. Selectable charging and discharging rate. Break-In: Also known as IEC capacity measurement and "Battery Forming". Charges battery at 0.1C for 16 hours, rest for one hour, discharges battery at 0.2C, then recharges again at 0.1C for 16 hours.
-
product
.13u ESD diode
Impulse TSMC
The Impulse TSMC .13u ESD diode was made to provide ESD discharge paths when integrating third party IP in an integrated circuit design for total ESD protection. The Impulse ESD diode has been successfully used with Dolphin Technologies, Artisan/ARM, TriCN/Synopsis I/O libraries, as well as popular IP blocks from RAMBUS, Chip Idea and other quality IP vendors. A 5.5 volt reverse bias anode to cathode operational specification enables the Impulse TSMC .13u ESD diode to be the device of choice for 5 volt tolerant designs.
-
product
Di Water Recycler
Eco Cycler
The Eco-Cycler Rinse Water Recycler is our third generation rinse water recycling system. The Eco-Cycler is designed to allow low-discharge cleaning systems such as the Trident LDO operate in a zero-discharge configuration. Constructed from the same hand selected materials as our line of defluxing systems, the rinse water recycler receives, re-dionizes and replenishes rinse water, creating a completely zero discharge cleaning solution and alleviating the requirement for a drain. These units care easy to connect and compatible with all generations fo Trident delfuxing systems.
-
product
Dry Arc Resistance Tester
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a...show more -
product
Field Strength Meters
FIM-22 And FIM-41
The Models FIM-22 and FIM-41 are portable field strength meters designed to provide precise, direct measurements of electro-magnetic fields in the 200 kHz to 5.0 MHz spectrum. These units include a receiver, integral shielded loop antenna, precision attenuator, internal calibration source, and battery power supply. With calibration accuracy traceable to the National Institute of Standards and Technology, the FIM-22 and FIM-41 meet the most exacting requirements of government and industry. Their ...show more -
product
Programmable Electrical Rule Checking tool
Calibre PERC
Calibre® PERC™, Mentor Graphics'' newest reliability verification solution is designed to address your advanced circuit verification needs for electrostatic discharge (ESD), electrical overstress (EOS), signals crossing multiple power domains, advanced ERC and other reliability concerns.
-
product
PD-Free High Voltage Transformer
YDQ
Wuhan Sangao Electrical Test Installations Limit Co.
PD-free HV Testing Transformer is a high-end testing transformer which firstly marketed in China by our company. The High-light characteristic of the equipment reflects the smallness in size, lighter in weight clean, oil-free, unnecessary static of field investigation, longer working life without maintenance and slightness in non-partial discharge. It is used for the insulators' voltage-resistance testing.
-
product
Battery Analyzer
KT-99/99A
Measure battery storage capacity with clamp-on sensorTest battery capacity under it’s real working conditionSelect different type of battery with discharge end voltageDisplay current and voltage during testingDisplay battery parameters and timeAuto-alarm when test finish,alternatively data savingAuto backlight on in dark areaMaximal capacity count up to 999.9Ah4-wires mode impedance measurement Up to 0.01mΩ resolutionOperating Environment: 0~40℃ ,<80% R.HStorage Environment : -20~60℃ ,<80% R.HPower supply: Heavy duty 9V Alkaline battery ( IEC-6F22)Accessories: “4 wire” test leads 1 pair “2 wire” test leads 1 pair
-
product
Portable PD Monitoring
ASM-P
The ASM-P can be configured with up to 32 PD sensor channels. If excessive discharge is detected, the ASM-P raises an alarm that can be configured either locally or by email/SMS. This enables the long-term assessment of plant conditions to be carried out quickly and easily, from any remote computer.
-
product
Partial Discharge Measuring Equipment
Electro Mechanical Enterprises
Partial discharge instruments have two modes of Wide Band and Low Frequency. You can use it for Partial Discharge tests of High-Voltage Equipment, Insulation Materials, High-Frequency Equipment, and Power Semiconductor devices. Partial discharge Measuring Equipment can easily realize the test of Partial discharge on print-circuit boards, connectors, semiconductors, small motors and other insulation materials, to make a judgment on good / bad of them
-
product
Partial Discharge Simulation Devices
Hangzhou Xihu Electronic Institute
Simulation device of cable PD faults, simulation device of switchgear PD faults, simulation device of GIS PD faults, simulation device of transformer PD faults.
-
product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of line...show more -
product
110V / 100 Amp Load
BD12-110P
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
product
48V / 300 Amp Load
BD18-48P-24/12
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.