Filter Results By:

Products

Applications

Manufacturers

Detectors

register the presence of a stimuli.

See Also: Metal Detectors, Particle Detectors, Sensors, Charge Sensitive Preamplifiers, Checkers


Showing results: 646 - 660 of 673 items found.

  • Halo Automatic Testing System

    Fortress Technology Inc.

    Our revolutionary Halo system is an automatic metal detector testing device. It is designed to automatically test ferrous, non-ferrous and stainless steel samples on all Fortress metal detectors. Automatic testing saves time, money, labor, along with removing the risk of human error and work place injury at critical control points on a manufacturing line while complying with industry standards. The Halo system is ideal for applications where manual testing of a metal detector is made difficult due to access, position, access to the product flow, environmental conditions, etc.

  • Sound Level Meter & Real-time Analyzer

    824 - Larson Davis, Inc.

    The Larson Davis System 824 combines advanced sound level meter and real-time analyzer capabilities into a rugged, user-friendly, ergonomic package. The base unit is an Integrating Sound Level Meter (ISM) that meets Type 1 Standards and offers simultaneous measurement of sound pressure levels using fast, slow, and impulse detectors, for A, C, and flat frequency weightings. This feature, termed ANY LEVEL™ measures 48 sound pressure parameters at once with a linear, 105 dB range. With firmware enhancements, the base unit expands as needed to accommodate multiple data processing requirements

  • Live-dead_Live Meter Verifier

    LDL-1100 - Allied Edison LLC

    The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 50 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL 1100 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.

  • Pair Tracing

    Tempo Communications, Inc.

    What use is your advanced tester if you cannot identify which wires to connect to? Traditional pair tracers allow you identify wire pairs remotely by applying some form of tone to the wire and using a detector to seek this signal at a remote location. Greenlee produces a wide range of tone generators and detectors from the very simplest, to advanced noise cancelling and highly sensitive types. Please remember that electrostatic wire tracing products cannot detect signals through soil or metallic conduits etc., as such signals are screened and you will need to refer to the "locating" section of this website for suitable products.

  • Live-Dead-Live Meter Verifier

    LDL-1200 - Allied Edison LLC

    The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 150 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL-1200 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.

  • Open Path Combustible Gas Detector

    SafEye (Quasar 900) - Teledyne Gas & Flame Detection

    The Open Path Combustible system detects hydrocarbon gases by analyzing the absorption of radiation caused by gases in the atmosphere and comparing it to background atmospheric absorption. This is accomplished between a pair of units: a Flash Source and a Detector that can monitor a distance of up to 200 meters.Open Path Combustible Gas Detectors are robustly designed and can handle the toughest environments: 316L stainless steel housings that meet IP66/IP68 and NEMA 250 6P egress standards; circuit boards epoxy coated for protection; MIL-C-810C testing for humidity, salt, fog, vibration, mechanical shock and temperature extremes; and SIL-2 approval per IEC61508 is a final statement in reliability.

  • X-Ray Inspection Systems

    Sciencescope International

    Scienscope’s X-Ray inspection systems division offers state of the art X-ray cabinet systems with the highest performance to price ratio in the industry today. Scienscope has over 16 years of experience selling solutions as a leading NDT (non-destructive test) supplier of x-ray inspection equipment into the electronic, medical device, materials, and biological markets. Our advanced x-ray systems feature high power micro-focus x-ray sources up to 130kV, high resolution digital detectors, large inspection stages with 350° degrees rotation, oblique angle inspection, and all of the manual and automated s/w tools you expect in an advanced system are included.

  • Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module

    sbRIO-9218 / 783362-02 - NI

    Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, … load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.

  • Digitizer

    724 Family - CAEN S.p.A.

    The 724 is a family of CAEN Waveform Digitizer able to perform basic waveform recording and run online advanced algorithms (DPP) of pulse height analysis and dynamic acquisition window. Data is read by a Flash ADC, 14-bit resolution and 100 MS/s sampling rate, which is well suited for high resolution detectors as Silicon, HPGe or inorganic scintillators like NaI or CsI coupled with Charge Sensitive Preamplifers. In the waveform recording mode, algorithms of zero suppression are also implemented to reduce the data throughput. The acquisition can be channel independent and it is possible to make coincidence/anticoincidence logic among diferent channels and external veto/gating. Multiple boards can be synchronized to build up complex systems.

  • Radiometer

    X1-1-RCH-116-4 - Gigahertz-Optik GmbH

    The X1-1 radiometer from Gigahertz-Optik features an RCH-116-4 detector and is ideal for measurement of the irradiance of high power LEDs in the UV-A and blue light range. The device can accurately measure irradiance levels of up to 40,000 mW/cm². One of the outstanding features of the RCH-116-4 detector is its proven concept of a passive radiation absorber coupled to a UV sensor. This provides stability even in high temperature and intense UV radiation environments. In addition to the passive radiation absorber, the device also has a cosine-corrected field of view. The sensor’s housing also serves as a handle. The battery-powered X1-1 optometer supports a usable dynamic range from less than 1 mW/cm² to 40,000 mW/cm² thanks to its high-end signal amplifier. It can be used to perform precise measurements of up to 5 standard LED wavelengths for which the detector was calibrated for active irradiance. In addition to the CW measurement function, the device also has a dose measurement function. The radiometer can be used with other detectors from the RCH series. e.g. for gas discharge lamps. Remote control of the device is possible via its user software and a software development kit is offered for integration of the device in the user’s own software.

  • Digitizer

    740 Family - CAEN S.p.A.

    The 740 is a high channel density CAEN Waveform Digitizer family able to perform basic waveform recording and run online advanced algorithms (DPP) of charge integration. Both the elevate number of channels per board (32 for Desktop and NIM form factor, 64 for VME) and the DPP algorithm make the board a digital replacement of a traditional QDC. Data is read by a Flash ADC, 12-bit resolution and 62.5 MS/s sampling rate, which is well suited for mid-slow signals as the ones coming from inorganic scintillators coupled to PMTs, gaseous detectors and others. Sampling rate can be further reduced using the decimation feature. The acquisition can be channel independent and externally vetoed/gated. Multiple boards can be synchronized to build up complex systems.

  • Longwave Infrared Thermal Camera

    FLIR A6780 SLS - Teledyne FLIR

    The FLIR A6780 SLS LWIR camera system makes it easy to measure temperatures of rapid thermal events and high-speed targets, making it an ideal choice for industrial, military, and manufacturing R&D applications. Thanks to its cooled, longwave Strained Layer Superlattice (SLS) detector, the A6780 provides faster snapshot speeds than other detectors for crisp images without motion blurring. Manual and remote-focus lens options provide flexibility to maximize the number of measurement pixels on the object of interest. Simple, single cable connectivity using Gigabit Ethernet provides complete camera control, plus data capturing in FLIR Research Studio software – so users can analyze and understand data faster than ever before.

  • USB Controlled RF Signal Generators

    Windfreak Technologies, llc

    Windfreak Technologies provides high value radio frequency devices such as RF Signal Generators, RF Synthesizers, RF Network Analyzers, RF Power Detectors, RF Mixers, and RF Frequency Converters. These devices can be used as RF Test and Measurement Equipment and controlled by Labview in an Automated Test Equipment (ATE) setup, or used as bolt-in RF modules in RF communications equipment. All products have innovative, powerful feature sets controlled by internal microprocessors so any settings can be memorized and used with or without a PC. Windfreak hardware also comes with the Labview GUI source code saving the end user hundreds of hours programming custom software.  Use one of our RF Signal Generators or other products risk free.  Return it if you dont like it.

  • Burner Control Flame Sensors

    SPECTRA BC11 IR and BC11 UV - Ametek Power Instruments

    The SPECTRA™ BC (burner control) sensors are extremely robust, compact, solid-state optical flame sensors that offer a host of features and provide maximum performance and reliability. SPECTRA flame sensors feature IR or UV detectors making them suitable for a wide variety of fuels, including coal, oil and gas. These units are 100% solid-state which enable the SPECTRA BC11 to be among the most compact industrial flame sensors available. There are no tubes or shutters to fail. Installation is simplified as the loop powered design only requires a single twisted pair cable for wiring connections. The 4-20 mA analog output provides direct connection to burner management systems eliminating the need for separate signal conditioners. High-temperature electronics enables the sensor to function at elevated operating temperatures.

  • Universal Multichannel System up to 8 kV

    CAEN S.p.A.

    - From 12 to 24 independently controllable High Voltage channels- 8 kV maximum output voltage- Maximum Current 1 mA- Either Radiall Multipin or SHV connectors- Available with either positive or negative polarity- Up to 500 pA/50 pA current set / monitor resolution- Up to 100 mV/10 mV voltage set / monitor resolution- Very Low ripple, down to < 5 mV- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Individual Floating (A1534 only)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down (1 ÷ 500 V/sec) - TRIP parameter- Current generator operation in overcurrent condition- Specific design for Germanium detectors (A15x0H only)

Get Help