Showing recent results 376 - 390 of 594 products found.
-
12-550 Mark III - Infrared Systems Development Corp.
The Spectral Master 12-550 Mark III Radiometer system provides versatility for almost any IR measurement task. The system allows simple field installation of various types of detectors, filters and optics, including Spectral CVF Filters for spectral measurements.
-
323 - Ballentine Laboratories, Inc.
The Ballantine 323 True RMS analog ac voltmeter uses advanced true rms circuitry to achieve square law response from rugged, fast responding silicon diode detectors with no thermal lag and overload vulnerability inherent in thermocouple devices.
-
Accumetrics Associates, Inc.
The Earth Fault Resistance Monitor (EFREM) and the Rotor Health Monitor (RHM) provide wireless rotor ground fault and temperature monitoring for generators and motors. The systems replace older slip ring contact ground fault detectors on any synchronous generator or motor.
-
Ridgetop Group, Inc.
We specialize in developing electronic prognostic solutions for critical systems. These include sensor array detectors, harnesses for "prognostics-enabling" critical systems, and analysis software to comprise a complete solution. Ridgetop's specialty? Determining the extent of aging and degradation, and rooting out troublesome intermittencies.
-
MS-321LR - EKO Instruments Co., Ltd.
The automatic Sky Scanner MS-321LR is designed only to measure Luminance and Radiance of the sky hemisphere. The sensor has 2 highly sensitive detectors which respond to the low light levels of the diffuse sky and will automatically block direct radiation by the active shutter function.
-
Premier Electrosystems
Premier's gas detectors can be used to detect combustible, flammable and toxic gases, and oxygen depletion. This type of device is used widely in industries and can be found in locations such as on oil rigs, to monitor the presence of toxix gases or any other gases which can harm human life.
-
DCS-120 Macro - Becker & Hickl GmbH
*FLIM of Macroscopic Objects*Scan Field Up to 15 mm Diameter*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Scanning by Fast Galvanometer Mirrors*Channel Seperation by Dichroic or Polarising Beamsplitters*Individually Selectable Pinholes and Filters*One or Two BDL-SMN or BDS-SM ps Diode Lasers*Tuneable Excitation by Super-Continuum Laser with AOTF*Two Fully Parallel Detection Channels*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: Two HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Wideband Version, Compatible with Tuneable Lasers*Electronic Pinhole Alignment*Optional: Spatial Mosaic FLIM via Motorized Sample Stage
-
RWP-700A - Kyowa Instruments
RWP-700A is a portable system to weigh and manage truck loads. It consists of the detectors that detect the truck weight by weighing the load of each wheel on the platform and the indicator that indicates, records and prints out the weighing result.For measurement, place detectors in parallel on a flat pavement surface, put front wheels on the respective detector platforms at the center and press the MEASURE key. Repeat the same for rear wheels. Pressing the PRINT key prints out the weighing result. Different from a stationary truck scale that weighs a truck with the whole truck body put on the detector, the portable system is allowed to be carried anywhere for measurement not only in factories but also in construction fields where the road surface is solid.
-
Menlo Systems Gmbh
Detection of weak light pulses on the few-photon level is crucial for many applications. The Menlo Systems' detector portfolio includes PIN photodiodes with low noise RF amplifiers, ultrafast avalanche photodetectors with integrated high voltage supplies, and detectors based on homo- and heterodyne detection.
-
CL-10GH - Automation Products, Inc.
The Dynatrol® CL-10GH Liquid Level Detector and EC-501A(G) Control Unit is used for high, intermediate or low point level detection of liquids and slurries. A unique vibrating principle permits design and operation features not available with other types of liquid level detectors.
-
V2740 - CAEN S.p.A.
The V2740 Digitizer is a 64-channel digital signal processor for radiation detectors in a VME64 form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others.
-
VX2745 - CAEN S.p.A.
The VX2745 Digitizer is a 64-channel digital signal processor for radiation detectors in a VME64X form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others.
-
V2745 - CAEN S.p.A.
The V2745 Digitizer is a 64-channel digital signal processor for radiation detectors in a VME64X form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others.
-
Konica Minolta Sensing, Inc.
Illuminance meter products are single element detectors that measure photometric brightness falling upon a surface. It is measured in footcandles or in lux. The Konica Minolta illuminance meters measure the amount of light that strikes a surface. These instruments display illuminance in either lux or foot-candles and they are lightweight, compact and portable.
-
Ophir Photonics
Pyroelectric sensors for measuring repetitively pulsed energy at up to 25 kHz. These sensors use a pyroelectric crystal that generates an electric charge proportional to the heat absorbed. The response time of the pyroelectric sensor depends on the time it takes for the heat to enter the crystal and heat it up. For metallic type pyro detectors, this time is tens of μs and thus the metallic type can run at a high repetition rate. For the BF and BB type, the response time is milliseconds with a correspondingly lower repetition rate. Ophir pyroelectric detectors have unique and proprietary circuitry that allow them to measure long pulses as well as short pulses and work at a high duty cycle, i.e. where the pulse width is as much as 30% of the total cycle time.