Showing results: 7741 - 7755 of 8141 items found.
-
Extech TM100 -
Extech Instruments Corporation
The Extech TM100 Type J/K Single Input Thermometer has a wide temperature range of -328 to 2501°F/-200 to 1372°C for type k and -346 to 2012°F / -210 to 1100°C for type j measurements. It has a high 0.1°/1° resolution and a large backlit LCD display with readouts in °F, °C, or Kelvin. The data hold function freezes the reading on the display and the screen displays the Max/Min/Avg. Readings capture a relative time stamp. Also, the offset key is used for zero function to make relative measurements. Auto power off with a disable feature. This thermometer comes complete with the Type K bead wire temperature probe and one 9V battery.
-
DDC Connectivity Power Controls
DDC's radiation-hardened, hybrid, Nuclear Event Detectors (NED) sense ionizing radiation pulses generated by a nuclear event, such as the detonation of a nuclear weapon, and rapidly switches its output from the normal high state to a low state with a propagation delay time of less than 20ns. The active low Nuclear Event Detection signal (NED) is used to initiate a wide variety of circumvention functions, thus preventing upset and burnout of electronic components. The NED output is also used to initiate both hardware and software recovery. This high-speed, 14-pin hybrid detector is used in electronic systems as a general-purpose circumvention device to protect memory, stop data processing, and drive power supply switches as well as signal clamps.
-
E5263A -
Keysight Technologies
Keysight E5262A and E5263A 2ch IV Analyzers are the low cost solution for current-voltage characterization. The E5262A and E5263A support two channels of SMUs (Source/Monitor Units) for voltage/current sourcing and voltage/current measurement with the best in the class current measurement performance as low as 5 pA. The Easy EXPERT group+ GUI based characterization software is furnished and available on your PC to support all the tasks required in the characterization from the measurement setup to the data analysis. Powerful integration of SMU's versatile measurement capabilities and GUI based characterization software makes the E5262A and E5263A the best solutions for characterization and evaluation of two or three terminal devices such as materials and active/passive components with uncompromised measurement reliability and efficiency.
-
M-OTDR-502 -
Fuzhou Metricu Technology Co Ltd
Optical Time Domain Reflectometer Wavelength 1310 / 1550nm, max test range 150KM, Dynamic range 28 / 26dB, SOR standard data saving, create PDF/EXCEL format report, stable laser source, support CW/270/330/1000/2000Hz, Test fiber's length, loss, attenuation parameters and event map, locate connection point/fusion point, Automatic analysis of various linkers/fusion points, easy analyze of various events,Support saving curves number ≥30000pcs, loss test, detect the optical or optical components loss value, etc. Test IP camera, optical power meter, visual fault locator, RJ45 cable TDR test, cable tester, cable tracer, etc.
-
Extech EX365 -
Extech Instruments Corporation
The EX365 is a Compact Industrial True RMS MultiMeter with a Built in Non Contact Voltage Detector. Featuring highly accurate True RMS measurements, LoZ for the prevention of false readings caused by ghost voltages, .5% basic accuracy, a 1000V AC/DC volt range, resistance up to 40MΩ, continuity beeper with visual alert, smart data hold, peak hold, auto power off with disable, relative mode for capacitance zero and offset adjustment. Additionally, the EX365 excels in frequency and capacitance measurements as well as commercial applications which require AC/DC current measurements from 1 mA to 10A. Complete with test leads, 9V battery, holster with tilt stand and built-in magnet.
-
Renesas Electronics Corp.
Renesas is renowned for its product lifetimes, and our memory products are no different. Our wide range of low power SRAM products provide high reliability, stable supply and long lifetime support often not found in these devices, making them ideal for industrial designs. Renesas’ ultra-fast QDR™ (Quad Data Rate) SRAMs are ideal for next-generation high bandwidth communication systems that require memories capable of very high operating frequencies combined with low latencies and full cycle utilization. Our EEPROM realizes high speed, low power consumption and a high level of reliability by employing advanced MONOS memory technology, a CMOS process and low voltage circuitry technology.
-
Atec, Inc.
Atec has made test equipment throughout all of its 65-year history. Test benches for aerospace and energy uses represent a significant segment of our experience. Atec has produced test benches involving hydraulics, mechanicals, electromechanicals, electronics, pneumatics, motors, and digital automation. Atec test benches have performed for challenging measurements, factory production, problem analysis and component overhaul scenarios. Today, complex test benches have capable data acquisition, control and communication systems integral in their electronics. Atec’s ADAQ™ system, based on COTS components and software, is proven and popular in test bench applications. DCUs, ECUs, FADECs and earlier analog or mechanical control units are easily interfaced.
-
MS111 -
MSG Equipment
The test bench is intended to test AC compressors of wide range of vehicles on R134a refrigerant. The equipment detects failures of a vehicle unit before its mounting in a car, whether it is a remanufactured, repaired unit or a used one. In the process of testing, data is shown on LCD display. It gives an opportunity to follow testing results realtime, save and/or print them due to software special features. Unit fixation mechanism is very flexible: a compressor can be easily fixed, no matter what kind of fittings it has. Units with electromagnetic clutch or electromagnetic valve can be tested both separately and simultaneously. Peculiar features of electric commutation are considered, connection polarity is identified automatically, indicator on the control panel indicates on presence of a diode in a circuit.
-
WAFRC -
Wuhan Sangao Electrical Test Installations Limit Co.
AC and DC voltage divider, Mainly composition by the high stability of passive resistance capacitance voltage divider and high precision digital kV table. The divider is passive resistance capacitance, Connected digit kV meter by coaxial cables. Which can be directly read out the AC, DC data measured from the table. This instrument has high precision, convenient operation, can be used instead of the electrostatic voltmeter. Device and the measuring line, power line, manual loaded box in light aluminum alloy, easy to carry and use. This equipment is mainly used for AC and DC high voltage measurement, and is suitable for power system's field measured and Institutions of higher learning laboratory's AC and DC high voltage measurement.
-
ZSX Primus IV -
Rigaku Corp.
As a tube-above sequential wavelength dispersive X-ray fluorescence spectrometer, the new Rigaku ZSX Primus IV delivers rapid quantitative determination of major and minor atomic elements, from beryllium (Be) through uranium (U), in a wide variety of sample types — with minimal standards. ZSX Guidance supports you in all aspects of measurement and data analysis. Can accurate analysis only be performed by experts ? No — that is in the past. ZSX Guidance software, with the built-in XRF expertise and know-how of skilled experts, takes care of sophisticated settings. Operators simply input basic information about samples, analysis components and standard composition. Measured lines with the least overlap, optimum backgrounds and correction parameters (including line overlaps) are automatically set with aid of qualitative spectra.
-
KLA-Tencor Corp
KLA’s advanced process control and process enabling solutions support integrated circuit manufacturing. Using KLA’s comprehensive portfolio of defect inspection, review, metrology, patterning simulation, in situ process monitoring and data analytics systems, IC manufacturers can manage yield and reliability throughout the chip fabrication process - from research and development to final volume production. SPTS provides deposition process solutions for insulating materials and conducting metals that cover a range of chip manufacturing process steps. IC manufacturers use KLA's array of products and solutions to help accelerate their development and production ramp cycles, to achieve higher semiconductor die yield and improved IC quality, and to improve overall profitability in the IC manufacturing process.
-
40-666-011 -
Pickering Interfaces Ltd.
The 40-666 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive. Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the40-666/667 User Manual.
-
40-667-011 -
Pickering Interfaces Ltd.
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the 40-666/667 User Manual.
-
NI
PXI Source Measure Units (SMUs) combine high-precision source and measure capability with features designed to reduce test time and increase flexibility. These features include high channel density for building parallel SMU test systems, deterministic hardware sequencing for minimizing software overhead, and high-speed update and sample rates for quickly changing setpoints and acquiring data. Additionally, the flexible sampling rate and streaming capability of PXI SMUs allows you to use the instrument as a digitizer to capture transient behavior, and the digital control loop gives you the ability to adjust the transient response of the instrument. The ability to change the transient behavior of the SMU, called SourceAdapt, reduces SMU settling time and minimizes overshoot and oscillations, even with highly capacitive loads.
-
HDGC-3915 -
HD Power Test Equipment Co.ltd
Battery Internal Resistance Tester is designed using the advanced AC discharge measurement method to test accurately voltage and resistance of battery. It is strictly designed to evaluate battery performance, state and life-time, which maintain all stationary power systems including Uninterruptible Power System. Battery Internal Resistance Tester can proceed the measurement in a group and in a single section of battery. With accurate testing of resistance and voltage, it gives an indication of battery capacity and technical status. The measurement data can be read on the instrument display directly. And it can also be uploaded to PC simply by using the USB drive. With the analyzing software, you could not only keep a record of the testing result but also have detailed analyzing for the status of batteries in different testing conditions.
