Showing results: 1486 - 1500 of 8174 items found.
-
Speed Test Pro -
Absolute Futurity
What is Speed Testing? Answer: Downloading data from the Internet and measuring the largest amount of data that can pass through your connection within a specified time period. Speed Test allows you to do this, completely autonomously without your intervention.
-
Model 9268 -
Telebyte, Inc.
Ensure clean data transmission and reception between two devices by installing Telebyte Model 9268 Opto Isolation Module with DB9 Connectors. For applications ranging from testing laboratories to factory floors, isolation is a critical component in data communications environments.
-
Mountains® -
Digital Surf
Analyze multiple types of surface data. Turn your surface data into accurate, visual surface analysis reports. See every feature with high quality real-time 3D imaging of surface topography. Characterize surfaces in accordance with the latest metrology standards.
-
USF-2000A -
Shimadzu Corp.
The USF-2000A implements materials fatigue testing at 20 kHz. Consequently, it is possible to evaluate 109 to 1010 order fatigue strength, where it had been difficult to obtain data before. Also, data for 107 cycles can be obtained in about ten minutes.
-
LL-230 -
Ametek Power Instruments
AMETEK LoadLoggers* and LoadProfilers are non-invasive digital recording loggers for gathering data on distribution loads and power quality. Whether the data is from a load site or direct from the distribution system, the AMETEK Load Management products are easy to install, operate and analyze.
-
S93010B -
Keysight Technologies
The S93010B time domain capability allows you to measure the time domain response of a device. The analyzer can transform frequency domain data to time domain or time domain data to the frequency domain and runs on PNA/PNA-L/PNA-X Series B models.
-
EVS -
Framos Technologies d.o.o.
Event-based Vision Sensors (EVS) help alleviate this issue by only sending data from pixels who have detected a change in intensity. This allows them to minimize the volume of data that is transmitted over the sensor’s data bus while minimizing the processing resources need to analyze the image. On top of this, individual pixel autonomously responds to illuminance changes allowing the sensor to detect small and/or high frequency changes with lower bandwidth requirements.
-
FLL222 -
Fifo Electronics
The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.
-
ME’scope -
Vibrant Technology, Inc.
Multi-channel time or frequency data can be imported from disk files, or directly from a machine or structure. The industry-leading photo-realistic interactive 3D shape animation allows you to observe order-related operating deflection shapes from running machinery, resonant vibration and mode shapes from real structures, vibro-acoustic shapes, and engineering data of any kind derived directly from experimental data. ME’scope contains state of the art tools for performing:
-
BAC600 -
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
-
BAC300 -
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
-
DS1610 -
Deviser Instruments
The Kingstone monitoring system offers real-time simultaneous signal monitoring and analysis on multiple return and forward paths of HFC networks. The DS1610 system is capable of capturing any transient noise and ingress noise and includes alarm setting, data storage, data analysis, data comparison in 3D and video recording, simplifying the installation, maintenance and troubleshooting of HFC networks. The user is also able to log in through any PC, enabling remote monitoring of the plant.
-
ADLINK Technology Inc.
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
-
webCS -
Astronics Corporation
The Ballard webCS® is the first highly integrated smart AID/server/router that securely bridges avionics data with wired and wireless networks in a single compact box. This wireless aircraft communications server platform is simple to install and configure, safe to interface with aircraft domains, and provides highly secure data transfer. The compact, versatile webCS enables aircraft operators to easily gather and process aircraft data, and then route it to where it is needed—whether on or off the aircraft.
-
NEST i4.0 -
ACOEM
Integrate your condition monitoring hardware and data with NEST i4.0 software.