Showing results: 1666 - 1680 of 5296 items found.
-
TD3202M -
Aplab Limited
- Fully Metallic Construction to Stop Radiated EMI- Compact & Rugged Design- DC Output ON/OFF on each Main Output- Voltage & Current Output Preset Facility for Safety- Constant Voltage / Constant Current Mode- 3 Digit DPM V and A- High Stability & Close Regulation ±0.01% +3mV- Low Ripple <1mV rms- Overload Protection- Convection Cooled – No Fans- Meets International Safety Standards
-
DT2 -
North Atlantic Industries
The DT2 module features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
PWR1-3B -
Schuetz Messtechnik GmbH
The RATIOMETER PWR1-3B is constructed to measure the transformation ratio, phase error and magnetizing current of power- and distribution- transformers for all three-phases simultaneously. Voltage and current transformers are single phase, power transformers normally three-phase. Due to the bad quality on industrial lines (phase jitter and shifting, voltage differences between the three phases) all measurements normally are done single phase, even on three phase ratiometers.
-
4016(800Vp,20Arms/200Ap) -
PRODIGIT Electronics Co, Ltd.
To analyze AC/DC power source, it requires a lot of parameters. Such as voltage(V), current(A), power factor(PF), Total Harmonic Distortion(THD), Crest Factor(CF), Inrush current, etc. To meet power saving regulation, the standby power measurement must be done. In this video I will show you how to operate this Prodigit Power Analyzer 4016. Furthermore, I explain what the parameter's meaning.
-
NEO TELE-TRONIX PVT. LTD
Contemporary Test Sets For Transformer Industries are developed to recognize the potentially disastrous current transformer errors. They prevent the primary current from overpowering insulation and short circuits. They are used for developing a testing and maintenance plan for addressing the errors before any failure to save money and time. With these powerful test sets, they are sure to perform saturation testing to test the knee point of a signal by comparing primary and secondary windings.
-
40-412-101 -
Pickering Interfaces Ltd.
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
MR12SPX -
Schuetz Messtechnik GmbH
The MR12SPX and its measuring probe are used for inspection and quality control of carbon strips of current collectors used by electrical powered trains, electric trams, trolley buses and similar vehicles. Here the current collectors are preferably roof mounted. Due to the often pairwise mounting of the carbon strips, there is little space between the lowered collectors. Therefore the measuring probe itself is very small. The design can be modified for your needs.
-
C&C Instruments Co.
Power Source : Wide Input(90V to 260V~) 50Hz/60Hz Output Current : 0~3A, 1A(Fixed) Rs-232C Interface(Option) Programmable(Option)
-
Brymen Technology Corporation
A digital multimeter (DMM) is a test tool used to measure two or more electrical values—principally voltage (volts), current (amps) and resistance (ohms).
-
SEM1630 -
Labfacility Ltd.
The SEM1630 is a DIN rail mounted trip amplifier which accepts RTD, Thermocouple, mV and passive current signals and provides a dual trip output
-
DL9101 -
Di-Log
Double moulded housing with an oversized high contrast 2000 count LCDdisplay. Manual ranging with current range up to 20A, temperature and frequency test.
-
DL9102 -
Di-Log
Double moulded housing with an oversized high contrast 2000 count LCDdisplay. Manual ranging with current range up to 20A, temperature and frequency test.
-
SH-055UMW / 10127 -
Suresafe Technology Inc.
This new portable Mobile Phone Detector is made for detecting 2G & 3G cellular phones (all current generations and all networks) communication in a place.
-
HG 200 -
Dr. Brockhaus Messtechnik GmbH & Co. KG
This process runs with constant flux alteration d/dt and avoids interference caused by eddy currents and phase displacement between the field strength and polarization measurements.
-
Renesas Electronics Corp.
Renesas' communications product portfolio includes a synchronizing pulse width modulating (PWM) current mode controller for subscriber line interface circuits (SLICs).