Showing results: 256 - 270 of 1386 items found.
-
15435A -
Keysight Technologies
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters.Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications.The converters are fitted with SMA connectors, one male, one female.
-
Renesas Electronics Corp.
Renesas has many options for DC/DC converters, controllers and regulators with buck, boost and buck-boost topologies.
-
VME-3125A -
Abaco Systems Inc
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
20IMX4-2 -
ELMA Electronic, Inc.
Rugged BMP Melcher™ DC/DC converter | power 4.1 W | input 8.4 - 36 VDC
-
Model 285 -
Telebyte, Inc.
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; Intelligent Control Of RS-485 Transmitter And Receiver; TD & RD LED's; DTE/DCE Compatible; Data Rates Up to 64 KBPs. The Model 285 RS-232 to RS-422/RS-485 Converter is a unique interface converter that can be configured to operate in compliance with RS-485 or RS-422 equipment, and RS-232.
-
Model 263 -
Telebyte, Inc.
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
DTE-3120 -
DekTec Digital Video B.V.
DekTec's standalone power-over-ethernet enabled ASI to IP Converter, allowing zero-jitter transmission of Transport Streams to IP networks.
-
S96082B -
Keysight Technologies
The S96082B scalar mixer / converter measurements enables the highest accuracy for scalar conversion-loss / -gain measurements with a simple setup and calibration
-
Carl E. Holmes Company
CEHCO can supply DC to DC Power Converters. We offer customized solutions. The DC to DC Power Converters are from 1 KW to 200 KW.We need additional information from the customer as shown below:DC input voltage rangeDC output voltage rangeMaximum output current requirement and rangeOther requirements (ex: response time, ripple, remote control… etc)
-
iWave Systems Technologies
The ARINC 818 to HDMI converter is a rugged standalone module available in half-length PCIe form factor used for ARINC 818 to HDMI conversion, HDMI to ARINC 818 conversion, 2x ARINC 818 Switch as well as ARINC 818 Duplicator/Splitter. It is a video Converter module designed with Kintex-7 FPGA, using an Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
Advantech Co. Ltd.
Review an extensive range of multi mode or single mode, Commercial and Industrial, Ethernet to fiber media converters that are designed for every conversion requirement.
-
DTE-3100 -
DekTec Digital Video B.V.
DekTec's standalone power-over-ethernet enabled IP to ASI Converter, allowing zero-jitter transmission of Transport Streams coming from IP networks.
-
Analog Devices Inc.
Analog Devices’ current source D/A converters (DACs) portfolio is ideal for photonics control applications where low current noise density, low dropout voltage, and high power efficiency, in addition to high channel density, is critical to system performance. The flexibility of the configurable current source D/A converter outputs, and 300 mA current delivery, make them suitable for resistive heaters and proportional solenoid drive.
-
ST-DRL ST-DSL ST Prefix -
Computer Conversions Corporation
Terminations subject to converter module features where applicable.Plastic backplane mount track included, or may be mounted using spacers at mounting hole locations.
-
Ironwood Electronics
Package converters provide an electrical and mechanical conversion from one package type to another. We use gold plated interconnects for our pin and through hole converters. Ironwood Electronics offers solder column adapters as a solution for leaded SMT packages such as QFP, PLCC, SOIC, SSOP, and TSOP. This is an excellent choice when you have a PC board in production that needs an upgrade or you need to replace an obsolete part.