Filter Results By:

Products

Applications

Manufacturers

Control

Known value


Showing results: 6856 - 6870 of 6967 items found.

  • *High Current Switches

    B-1002 - Ruetz Technologies GmbH

    Ross High Current Switches are available up to 36,000 amps continuous and over 1,700,000 amps 20µsec RC pulse, with voltage ratings of 6 volts to 400kV peak test. Standard Ross high current switches are built with 80 to 120psi air cylinder actuators. Air cylinder or motor operated for high contact force.  Arcing contacts optional for closing current. G-10 epoxy glass laminate is standard insulation on most models. G-7 silicone glass is used on models available for RF applications above 100kHz.  Most Ross high current switches are available with additional lengths of insulation, where the high voltage contacts need to be spaced at a greater distance from the actuator and control circuit.  Voltage withstand value is at least doubled and the interrupt capability is much greater when high current switches are immersed in insulating oil, fluid or SF6 gas.  For gas atmosphere, no modifications are necessary; however, oil or fluid immersion requires modification at a slight extra cost.

  • High Current Switches

    B-1002 - ROSS ENGINEERING CORPORATION

    Ross High Current Switches are available up to 36,000 amps continuous and over 1,700,000 amps 20µsec RC pulse, with voltage ratings of 6 volts to 400kV peak test. Standard Ross high current switches are built with 80 to 120psi air cylinder actuators. Air cylinder or motor operated for high contact force.  Arcing contacts optional for closing current. G-10 epoxy glass laminate is standard insulation on most models. G-7 silicone glass is used on models available for RF applications above 100kHz.  Most Ross high current switches are available with additional lengths of insulation, where the high voltage contacts need to be spaced at a greater distance from the actuator and control circuit.  Voltage withstand value is at least doubled and the interrupt capability is much greater when high current switches are immersed in insulating oil, fluid or SF6 gas.  For gas atmosphere, no modifications are necessary; however, oil or fluid immersion requires modification at a slight extra cost.

  • 5G Active Antenna Innovator’s Kit

    AWMF-0129 - Anokiwave Inc.

    The AWMF-0129 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0108 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0108, the antenna provides +50dBmi output power while consuming just 12W DC power in the RF circuits and has achieved Gb/s data rates in OTA trials. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWMF-0129 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.

  • Display Color Analyzer

    Model 7123 - Chroma ATE Inc.

    Luminance and chromaticity measurement of Color Display0.005 cd/m2low luminance measurement (A712301)Wide luminance range: 0.0001 to 25,000 cd/m2 (A712301) 0.01 to 200,000 cd/m2 (A712302)High accuracy measurementMaximum 9 display modes: xyY, TΔuvY, u’ v’ Y, RGB, XYZ, Contrast, ProgramAble to control Video Pattern Generator and UUT (Unit Under Test)Built-in contrast measurement function to calculate the contrast ratio directlyEquipped with programmable test items that can complete the planned tests with one single buttonSupport USB flash disk that can copy the test procedures to other station for useJudgment function embedded to judge the test result automatically with one single buttonCalibration period setting and reminding functionMemory for storing 100 channels of standard color data and calibration dataBuilt-in flat display calibration data LCD-D65 & LED-D65* to be applied for chromaticity measurement instantlyOptional display white balance alignment system can be used to integrate all optical test stations to one single station

  • Optical CMM Systems

    RedLux Ltd

    Our OmniLux metrology system is highly versatile and provides unparalleled levels of 3D CMM capture for component measurement in seconds. This high precision non contact, metrology system is extremely versatile because it measures components of any geometry and of any material. Geometries possible include: spheres, asphere, cylinder, internal bore, cone/taper, step height or freeform in any material such as polished or rough metals or ceramics and polymers. The Omnilux is fast and accurate because, unlike direct contact sensors, the use of optical sensors means that the whole surface can be analysed while the object is suspended in space, ensuring that no damage comes to delicate surfaces. Our easy-to-use software interface, developed from years of experience enables the operator to effortlessly control the system. Rich data analysis, automation and export of results for the immediate generation of reports as well as a compact footprint means OmniLux is the leading solution for production or R&D environments where reducing cycle times is critical to sustainable success.

  • Optical Measurement

    Sylvac

    • Vertical optical measuring machine for static and dynamic measurement of various elements on small cylindrical parts.• The parts can be mounted between two centres or held in place using various accessories.• Attractive design and robust construction with many new features: New touch screen control panel for easy operation directly at the workplace, bi-telecentric optical system, high resolution CMOS camera, precision sliding headstock with integrated and protected daily standard, quick and easy accessory changing system, integrated temperature sensors, dynamic LED indicator of the general status of the measured part (GO/NG) and operator messages. Equipped with an exclusive optics tilting system.• Machines specially designed to measure threads such as, parallel, trapezoidal, conical, round, square, conical, worms, ball screws, bone screws, dental implants, etc.• Reflex SCAN+ concept for measuring parts without prior programming at the touch of a button• Delivered complete with a PC and the Reflex SCAN+ software, which allows a multitude of elements to be measured easily and intuitively.

  • COMPUTERIZED LCRTZ TEST SYSTEM (Automatic Transformer Test System)

    CVCT-S20 - Vasavi Electronics

    Ideal for fast and fool proof testing of COILS AND SMALL TRANSFORMERS like SMPS transformers, Telecom transformers (HYBRID, POT CORE, RM-CORE), Pulse transformers etc. The systems scans at one stroke, all the windings of a transformer and tests as per definition of test procedure. The test procedure can be pre-programmed and stored under User friendly menu driven software . Any semi-skilled and unskilled person can be engaged for actual testing purpose. Can Select test frequency, pin number, parameters, test conditions, limits for each test. Test any pin to any other pin any defined parameter.Test Parameters :-> Inductance-> Capacitance-> AC Resistance, -> DC Resistance, -> Impedance, -> Leakage Inductance,-> Transformation Ratio & Winding PolaritySPECIFICATIONS :Measurement Frequencies : 50 Hz, 100 Hz, 500 Hz, 800 Hz; 1 KHz, 2 KHz, 5 KHz, 10 KHz. Measurement Voltage: 0.1 V – 1.0 V RMS adjustable under program control.

  • Radiator Flow Test Machine

    8601 - Hydraulic Technology, Inc.

    The Radiator Flow Test Machine P/N 8601 meets all requirements of military specification MIL-F-45955A (AL). It is completely self contained and requires only connection to a source of shop electrical power to place in operation. A power cable complete with three prong grounding plug is permanently attached to the machine for this purpose. The unit consists of a water storage tank, a pumping system, a flow measuring system, a support and workstation, and the required hose adapters for connection to different size radiators. The complete unit is mounted on swiveling casters. The flow rate is infinitely adjustable from 0 to 120 gallons per minute by means of a panel mounted control valve. The machine is constructed from heavy 10 gauge steel, is double welded and is coated externally and internally with a water-resistant epoxy coating. Flow measurement is accomplished by a digital panel meter with a calibrated accuracy of plus or minus 3 percent of scale between 5 and 120 gallons per minute. Higher flows available on request.

  • AC/DC - Enclosed SMPS Power Supply

    Mornsun Guangzhou Science & Technology

    MORNSUN AC/DC enclosed switched-mode power supplies (SMPS) feature complete EMC tests and protections, high efficiency, and wide selection. MORNSUN SMPS withstands 300VAC surge input for 5 seconds. 305RAC (305Vin reliable under all conditions) AC to DC SMPS module is included. 305RAC Series is a collection of AC/DC converters that can run from nominal 85 VAC up to 305 VAC and are safety certified to UL/IEC/EN standards, with CB Reports. These AC to DC enclosed switching power supplies in MORNSUN SMPS Power Supplies portfolio meet IEC/EN61000-4, CISPR32/EN55032, IEC/UL/EN62368, EN60335, and GB4943 standards and are widely used in areas of industrial, LED, street light control, electricity, security, telecommunications, smart home, etc. They comply with the latest global energy efficiency standards. The most high-quality AC to DC SMPS ranging from 15W to 1500W witness the continuous innovation of MORNSUN SMPS power supply family.

  • Scanning Acoustic Microscopy (CSAM)

    National Technical Systems

    Scanning Acoustic Microscopy, also known as C-SAM or Acoustic Micro Imaging or AMI, outstanding benefit is its ability to find hidden defects within assemblies and materials that can occur during manufacturing or environmental testing. Defects such as delaminations, voids and cracks can be identified and analyzed more effectively using Acoustic Microscopy than with any other inspection method.Unlike other non-destructive techniques such as X-Ray and Infrared Imaging, Acoustic Microscopy is highly sensitive to the elastic properties of the materials it travels through. Because of this, the ability of Acoustic Microscopy to find and characterize these physical defects is clearly superior. Typical applications include production control, failure analysis, and product development.Through the use of ultra-high frequency ultrasound, C-SAM non-destructively finds and characterizes physical defects—such as cracks, voids, delaminations and porosity— that occur during manufacturing, environmental testing or even under normal component operation. Because of the unique aspects of the technology, AMI can locate these defects better than any other inspection method.

  • ASA240

    Electron Plus

    The ASA240 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA240 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.The built switching matrix (40 x 2) is easily configured from the software and maybe used with adaptors (such as DIP or SO) to speed up testing of boards, or maybe connected to a ‘bed-of-nails’ to facilitate rapid testing of boards in production.With the ASA240 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.

  • Electronic Tire Tester

    Model BTT-5700 - Branick Industries, Inc.

    The Branick BTT-5700 was created from the ground up to be the most efficient, durable and reliable electronic tire tester available. The electronic detector accurately locates flaws that may be missed using conventional methods. A visible spark occurs at the site of a flaw and the rotation stops to allow the flaw to be marked. The adjustable height platform reduces physical strain that can often lead to workers compensation claims. The BTT-5700 also features a bi-directional variable speed electric rotation motor that is whisper quiet. The auto extend/retract ramp makes tire loading easy. Hand controls are located on a locking swing arm that can be adjusted in seconds. Four air tool ports and two electric outlets are also provided so any needed tools can be kept close for improved efficiency. A high power LED light and Medium Truck Probe are also included. All probe heads require only the push of a button to change and are available to fit all common tire sizes. And, like everything from Branick, it's made in the USA.

  • UV Fluorescence Hydrogen Sulfide Analyzer

    Model T101 - Teledyne Monitor Labs

    The Model T101 H2S analyzer uses the proven UV fluorescence principle to measure hydrogen sulfide at levels commonly required for ambient air monitoring.The Model T101 is equipped with an internally mounted catalytic converter set at 315°C to convert H2S to SO2. A switching mode alternately measures H2S and SO2 while showing both readings concurrently on the front display.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T101 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ S​oftware. ​​

  • Video Pattern Signal Generator

    Model A223800/01/02/03/04 - Chroma ATE Inc.

    Support 8K Super Hi-Vision (7680x4320/8192x4320)Independent graphics core for 8K Super Hi-Vision pattern with less than 200 msec. switch timeUp to 4 signal modules per unitUp to 4 resolution and pattern outputs.7 inch 1024x 600 high-resolution touch panel, GUI interfaceBMP file format supportUSB 3.0 data accessGigabit Ethernet high-speed network interfaceHDMI 2.0a signal module (Optional) - 8K x 4K 60 Hz (4 HDMI port) - 4K x 2K 60 Hz (1 HDMI port) - Pixel rate up to 600MHz (6Gbps TMDS rate) - RGB 4:4:4 / YCbCr 4:4:4 or 4:2:2 or 4:2:0 - HDCP 2.2 / 1.4 - Wide color gamut (ITU-R BT.2020/DCI-P3) - HDR (High Dynamic Range) Testing (HDR infoframe & metadata / EOTF) - SCDC (status & control data channel) Reader

  • cRIO-9032, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, WiFi, 4-Slot CompactRIO Controller

    784548-01 - NI

    1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, WiFi, 4-Slot CompactRIO Controller - The cRIO-9032 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9032 also features dual-band, 802.11 a/b/g/n WiFi communication to help you connect to HMIs, the cloud, and other devices. Additionally, the cRIO-9032 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.

Get Help