Showing results: 1426 - 1440 of 2822 items found.
-
EA4-COUNTRY -
ELMA Electronic, Inc.
The EA4-COUNTRY is a 3U CPCI Express peripheral slot carrier card with up to x8 low-profile PCI Express connectors. Suitable for use in PXI Express systems.
-
AD-902 -
ADEX Urzadzenia Pomiarowe
The instrument is designed for the direct measurement of insulation resistance of cables and electrical equipment especially in the telecommunications and communications. It can also serve as a tester for example go. Circuits or connectors.
-
T1000-37 -
Tesuto Systems
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
40-747-731 -
Pickering Interfaces Ltd.
The 40-747 is a single 16 to 1 RF MUX available in 50 Ohmhm or 75 Ohmhm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohmhm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions.Applications for the 40-747 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Coaxial Dynamics
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
4000 Series -
Coaxial Dynamics
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
SpecVision -
KrellTech
SpecVision is a video probe that engages directly with Krell polishing machines. This permits the viewing of polished optical surfaces while connectors or bare fibers are still loaded in the polisher. This in-line video inspection technique minimizes material handling and potential damage/contamination that may occur when transferring components from the polisher to a traditional microscope. SpecVision can interface with Scepter, SpecPro and Rev Polishers.
-
410104272 -
Virginia Panel Corporation
The G10 ITA is equipped with a removable EMI-shielded cover. The cover slides up to provide access to wires and connectors and is secured by two screws. The removable and adjustable U-shaped cable clamps are attached by screws to the ITA frame and allows ITA modules to be pre-wired before assembly. The clamps can hold cable bundles with an oblong bushing effective diameter of 1.55". ITA strain relief plates are not needed.
-
410120110 -
Virginia Panel Corporation
The G2 ITA is equipped with a removable EMI-shielded cover. The cover slides up to provide access to wires and connectors and is secured by two screws. The removable and adjustable U-shaped cable clamp is attached by screws to the ITA frame and allows ITA modules to be pre-wired before assembly. The clamp can hold cable bundles with an oblong bushing effective diameter of 1.55". ITA strain relief plates are not needed.
-
Cimetrics Inc.
Cimetrics offers several modules that can enable you to add BACnet capability to your products. Our modules, based on the Lantronix XPort, are elongated Ethernet RJ45 connectors that can be built into your product. Each module contains a microprocessor, memory, Ethernet MAC/PHY, serial (UART) interface, and firmware written by Cimetrics. The serial interface is typically used to communicate with another microprocessor in your product.
-
510150148 -
Virginia Panel Corporation
This PCB Adapter was designed specifically for the NI PXI-2529, which uses 160 signals at 2 amps. This PCB Adapter will accommodate one or two NI TB-2634 terminal blocks. If 192 signals or 3 amps are needed for a different application; use # 510 150 155 which has 6 32-pin ribbon cable connectors capable of up to 3 amps each.
-
4624-3 -
VECTOR Electronics and Technology, Inc.
120 contacts (60 each side) on 0.050" centers. Overall GND plane, Pad-Per-Hole, Peripheral Buses. Isolated pads around each hole. 32-bit ISA format. Universal tab fits both 3.3V and 5V tab notch patterns. Mounting bracket included.Peripheral buses for voltage and ground distribution.I/O mounting area for D-sub and ribbon cable connectors.
-
Euresys Inc.
4x BNC connectors on the bracket, expandable to 16 with three [1203] VEB modules (sold separately)PCIe x1 busSixteen shared video decoders, 100/120 images per second (200/240 fields per second)Real-time acquisition from 4 cameras, fast switching between up to 16 camerasIndependently-programmable frame rate and acquisition parameters for each video input
-
BEI Industrial Encoders
Rotary potentiometers are available in wirewound, conductive plastic and hybrid configurations. Single or multi-turn configurations are available up to 3600 (10-turns) of motion. These rugged, reliable contact sensors can meet IP66/67 sealing requirements and provide operational life exceeding 10 million cycles. A variety of terminations are available, including integral connectors and flying leads. Adapted and custom solutions for are also available.
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
The wide product range means that a variety of semiconductor test applications and high-speed digital applications are possible. To meet the ever-challenging technological requirements and increasing demands of the semiconductor test equipment industry, Rosenberger has developed and produces multiport mini-coax connectors and cable assemblies – for applications up to 40 GHz – , and spring-loaded coax products. Probes and customer-specific cable assemblies are also available.