Showing results: 1501 - 1515 of 2818 items found.
-
OS405 -
Advanced Fiber Solutions
The OS405 (635nm) visible laser cable fault locator allows the operator to find faults in fiber optic cables, even in the OTDR dead zone, optimizing splices and tracing fibers. By injecting a bright red visible light in the fiber, locations of losses such as breaks, bends, or bad connectors can be detected visually, even through the typical yellow or orange jacket used on most single fiber cables.
-
Electro Mechanical Enterprises
Partial discharge instruments have two modes of Wide Band and Low Frequency. You can use it for Partial Discharge tests of High-Voltage Equipment, Insulation Materials, High-Frequency Equipment, and Power Semiconductor devices. Partial discharge Measuring Equipment can easily realize the test of Partial discharge on print-circuit boards, connectors, semiconductors, small motors and other insulation materials, to make a judgment on good / bad of them
-
Q7B300 -
Axiomtek Co., Ltd.
*Qseven module evaluation purpose*1 Gigabit Ethernet port*2 SATA connectors*2 RS-232/422/485 & 1 RS-232*3 PCIe x1 slots*3 USB 3.0, 1 micro USB 2.0 port (optional)*1 PCI Express Mini Card slot (PCIe+USB+SMBus)*1 SD card slot*1 LVDS (or eDP)/DP connector
-
RSC -
Rohde & Schwarz GmbH & Co. KG
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
ICS Electronics
*One, two and three slot-wide kits for VXI Modules with 150-pin connectors. Shroudless design fits rev 4.0 chassis. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber Interferometer is an automatic, non contact fiber endface interferometer for single fiber connector developed by SunmaFiber. It is designed to measure the geometry parameters of single fiber connector end-face. Equipped with auto focus and auto centering functions, SUNMA INTERFEROMETER is very accurate and stable, it can also test bare fiber and bare ferrule. It is very helpful in fiber connector manufacturing to increase the quality of the connectors.
-
44-965-068-F -
Pickering Interfaces Ltd.
Suitable for use on the front of PXI BRIC modules this connector block provides a simple method of connecting to high density 68-Pin SCSI Style Micro-D connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
SFF-ATR-VPX -
ELMA Electronic, Inc.
This ½ ATR platform is designed for use in harsh environments. The unit is designed to house three 3U VPX (VITA 48.2) payload cards and one 3U VPX (VITA 62) PSU and protect them from harsh environments. The backplane supports up to 4 slots on a 1” pitch. Up to 120 high speed differential pairs can be routed to the front panel connectors for interconnection with external equipment.
-
SY8-CYCLONE -
ELMA Electronic, Inc.
The SY8-CYCLONE is a CPCI Serial FPGA based peripheral board with up to 10 RJ45 Ethernet ports. Via the PCI Express© x4 interface, FPGA can be used as Ethernet NIC, switch, router, or gateway. Single width offers up to 5 RJ45 connectors, or 8HP width with up to 10 ports. Can be paired with a second FPGA for redundancy, or additional logic elements for custom solutions.
-
DP-VME-4059 -
Data Patterns Pvt. Ltd.
DP-VME-4059 is a rugged module with 48 channel relay output, constructed using 2 Form 'C' Double Pole Double Throw (DPDT) relays. The relay channel operation is controlled through the VME bus. Internal read-back is provided to confirm the selected commands. The pole, Normally Closed (NC) and Normally Opened (NO) contacts are terminated at a pair of front panel 96-pin EURO male connectors.
-
XCVR-AS5653 -
Avionics Interface Technologies
AS5653 SFP transceiver that can be inserted into any standard SFP slot - 1.0625 GBPS communication signals interface using TNC connectors - Bulkhead mountable female TNC connector at the end of a 1 meter length of RG179B/U - 100 feet of RG179 operates to better than 10E‐13 Bit Error Rate - Available for 75 Ohm single ended copper or 150 Ohm Differential
-
Lightel Technologies, Inc.
Lightel's benchtop scopes use a USB connection to Windows®-based PCs and tablets to view and save clear detailed images of connector endfaces. Our benchtops provide cost effective innovative solutions for inspecting connectors where standard Fields of View may not be adequate. Each benchtop scope comes with easy to use software designed to take best advantage of that scope's capabilities.
-
EM-7021 | 2 GHz – 5 GHz -
Electro-Metrics Corp.
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
EM-7020 | 1 GHz – 2.5 GHz -
Electro-Metrics Corp.
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
ATHENA IV -
Diamond Systems Corp
Each generation of Athena maintained the same physical shape and most of the I/O connectors and features of the previous generations, while updating key features to stay current with the state of the art. In this way the Athena platform has maintained a low-impact migration path for customers with extended product lifecycles that outstrip the lifetimes of the CPU. Many customers have been able to maintain their products for up to 16 years as a result.