Filter Results By:

Products

Applications

Manufacturers

Component

Testing of individual hardware or software components or groups of related components.


Showing results: 1726 - 1740 of 2783 items found.

  • Clock and Trigger Distribution Card

    Spectrum Instrumentation

    The clock and trigger distribution card is a simple and passive component that allows to synchronize several systems externally. No programming is necessary. A clock can be fed in from an external device or as an option an internal clock oscillator can be equipped by the factory. This clock is then also used to synchronize an external trigger signal into the clock domain. Both, clock and synchronized trigger, are then fed into a maximum of 17 different systems. Each system can be a single card or a synchronized set of cards that run with an internal star-hub.

  • Accessory Kit, Type-N to BNC, 50 Ohms

    11854A - Keysight Technologies

    The Keysight 11854A accessory kit furnishes the RF components required for measurement of devices with 50 ohm, BNC connectors and when using a network analyzer with a type-N configuration. The BNC accessory kit contains two type-N male to BNC female adapters, two type-N male to BNC male adapters, two type-N female to BNC female adapters, two type-N female to BNC male adapters, a BNC male short, and a storage case.

  • Vector Network Analyzers Handheld

    Anritsu Corporation

    Wireless VNA Master + Spectrum Analyzer, the industry's broadest frequency handheld solution to address cable, antenna, component and signal analysis needs in the field: with frequency coverage from 5 kHz to 6/20 GHz.

  • Solar simulation systems

    Iwasaki Electric Co., Ltd.

    Whatever your application, from an environmental chamber for small components to an extensive array for a complete automobile or aircraft test, EYE / Iwasaki has the experience to provide a solar lighting system customized for your requirements.

  • Magnetic-Field Test System

    MTS-800 - FRANKONIA GmbH

    The MTS-800 is a compact test system for broadband generation and measurement of magnetic fields. Its internal components allow automatic EMC tests according to automotivestandards where high field strength need to be generatedor measured.

  • Laser Test Systems

    Santa Barbara Infrared, Inc.

    Santa Barbara Infrared, Inc. offers an extensive family of test systems and components that test and characterize the performance of laser range finders, designators, illuminators and spot trackers. In this section, detailed information is provided for the following:

  • Pneumatic Bump Test Machine

    KRD20 series - CME Technology Co., Ltd.

    The KRD20 series pneumatic bump test machine replaces the traditional mechanical cam-type crash bench and is suitable for repeated impacts on electronic components, equipment and other electrical and electronic products during transportation or working.

  • Electric Fatigue Testing Machine

    EFT Series - Jinan Testing Equipment IE Corporation

    EFT series electric fatigue testing machine is an ideal platform to test a variety of materials and components for the following high demanding tests: Quasi-static test; Reverse-stress mechanical low cycle fatigue loading tests (LCF); High temperature creep, stress-rupture, relaxation tests in load/strain control mode for medium-term or long term period. Mechanical fracture tests like crack growth & toughness tensile/compression test for ceramics in both room- or vacuum-, high- temperatures up to 1200 C conditions etc. Compression test on plate springs or clutch springs etc. It is also widely used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastrometric materials, etc. It adopts electric actuator structure with all-elastic, backlash free, central ball-lead screw driving to achieve direct force transmission to the specimen, it is especially a perfect choice for R&D institutes, universities, nuclear power, automotive and aviation, & aerospace sectors from metals, composites, ceramics, springs and component parts.

  • Crawler Control Unit

    CCU186 - Teledyne ICM

    The CCU186 control unit for crawlers possesses a distinct advantage compared to existing products. In fact, all of the performances that are usually achieved with standard control units are now available in the crawler configura­tion. Automatic slow preheating, the progressive rise in voltage with each exposure, as well as a selection of set values are all included in the CCU186.As the CCU186 has been entirely fitted with industrial electronic components, it is perfectly suited to the often extreme conditions of automatic intra-tube control campaigns.

  • Hydrogen Fluoride Gas Monitor

    GASERA ONE HF - Gasera Ltd.

    Hydrogen fluoride, chemical formula HF, is a colorless, highly irritating already at very low ppm levels, corrosive gas and can exist as a fuming liquid. Reaction with water is rapid, producing heat and hydrofluoric acid. Hydrogen fluoride (HF) is used in manufacturing of refrigerants, herbicides, pharmaceuticals, high-octane gasoline, aluminum, plastics, electrical components, and fluorescent light bulbs, among others. Hydrogen fluoride (HF) is very soluble in water and is readily absorbed in the upper respiratory tract.

  • i-PULSE

    M-Series - Amistar Automation, Inc

    The M-series machines from i-PULSE are built on a ‘foundation of bedrock.’ That foundation is in the form of a one-piece cast frame, from the gantry components to the floor, which give the machines tremendous strength and rigidity. This eliminates any vibration and allows for high-speed operation without loss of accuracy, and a long lifespan without loss of accuracy. The critical surfaces are finished by hand, down to micron order, to achieve an unsurpassed level of machine accuracy without the need for shims or other ‘extra pieces.’

  • ISL911xx Family Of Buck-Boost/Boost Regulators

    Renesas Electronics Corp.

    The ISL911xx buck-boost regulator family is capable of working with the ultra-small inductors and capacitors to fit within less than 14mm2 board footprint, making them the ideal 2A switching converter solution for space-constrained mobile devices. The advanced wafer-level CSP package requires only a single inductor and very few external components, which minimizes overall space requirements. The ISL911xx regulators’ 2.5MHz switching frequency further reduces the power supply solution size.

  • Partial Discharge Test Set

    NEO TELE-TRONIX PVT. LTD

    We are an unparalleled name in the industry, engaged in manufacturing and exporting Partial Discharge Test Set that is broadly used for instrument transformers to test the discharge of voltage. This test set is manufactured in compliance with set international quality standards using optimum quality components under the observations of our experienced professionals. Further, it is made available in several specifications to meet the exact requirements of the clients. Our offered Partial Discharge Test Set can be owned from us at nominal prices.

  • Single Fiber Aligner

    1100 - Photon Kinetics

    The 1100 Single Fiber Aligner uses patented fiber alignment concepts to produce virtually instantaneous temporary couplings for OTDR, dispersion, or any other optical fiber or component test that requires a fiber-to-fiber connection. It delivers low loss, low reflectance couplings on the first try virtually every time, without the need for test instrument feedback. As a result, temporary coupling times are minimized and manufacturing costs are reduced without compromising product quality.

  • Compact Multi-sensor Gyro-stabilized Surveillance System

    UltraFORCE® 275-HD - Teledyne FLIR

    Extremely low SWaP makes the UltraFORCE 275-HD the optimal choice for weight, power and footprint-constrained platforms. The system delivers multi-spectral HD imaging performance for airborne homeland security, combat, patrol, surveillance, reconnaissance, and search and rescue programs. Durable and built to endure long missions, it’s designed for lightweight manned and unmanned airborne platforms. Built in Europe with no U.S.-sourced components, the UltraFORCE 275-HD is ITAR-free, increasing exportability and freedom of movement within Europe.

Get Help